Planar Pd7060 Projector User Manual

							11
Bottom View
ITEMLABELDESCRIPTION
1Ceiling support 
holesContact your dealer for information on mounting the projector on a
ceiling
2 Tilt adjuster Adjust angle of the picture
3Height adjuster 
buttonPush to release height adjuster
4 Height adjuster Adjuster drops down when adjuster button is pushed
2
1
3
4 
						

							12
Remote Control Functions
ITEMLABELDESCRIPTION
1 Power on Turns projector power on
ON─ POWER─ OFF
1
23
45
SOURCE
2 Power off Turns projector power off
3 Source 1 User confi gurable (Default: HDMI)
4 Source 2User confi gurable 
(Default: Component)
5 Source 3 User confi gurable (Default: DVI-D)
6 Source 4 User confi gurable (Default: PC)
7 Source 5User confi gurable 
(Default: Video/S-Video)
8 Up cursor
Navigates and changes settings in the 
OSD
9 Left cursor
10 Enter Changes settings in the OSD
11 Right cursor
Navigates and changes settings in the 
OSD
12 Down cursor
13Menu Opens the OSD
14ExitExits OSD menus or menu selection 
fi elds
15 Hot key 1 User memory setting 1
16 Hot key 2 User memory setting 2
17 Hot key 3 User memory setting 3
18 Contrast Adjusts screen contrast
19 Brightness Adjusts screen brightness
20 Aspect ratioToggles aspect ratio: 
16:9 → Letterbox → 4:3 → Native
21 GammaToggles gamma: Film → Video → Cin-
ema → PC → Photo
22 OverscanToggles overscan: 
Off → Crop → Zoom
23 Keystone Adjusts keystone 
24 AutoAutomatically synchronizes display 
settings in RGB mode
25 Blank Makes the screen blank
26 LED Turns back LED light on and off 
						

							13
Remote Control Operating Range
The remote control uses infrared transmission to control the projector. It is not necessary to point 
the remote directly at the projector. Provided you are not holding the remote control perpendicular 
to the sides, the remote control functions within a radius of about 10 meters (33 feet) and 30 
degrees above or below the projector level. If the projector does not respond to the remote control, 
move a little closer.  
Important!
Avoid using the remote control with bright fl uorescent lighting turned on. 
Certain high-frequency fl uorescent lights can disrupt remote control operation.
Be sure nothing obstructs the path between the remote control and the projec-
tor. If the path between the remote control and the projector is obstructed, you 
can bounce the signal off certain refl ective surfaces such as projector screens.
The buttons and keys on the projector have the same functions as the cor-
responding buttons on the remote control. This user’s manual describes the 
functions based on the remote control.  1.
2.
3.
Projector and Remote Control Buttons
The projector can be operated using the remote control or the buttons on the top of the projector. 
All operations can be carried out with the remote control; however the buttons on the projector are 
limited in use. The following illustration shows the corresponding buttons on the remote control 
and on the projector.
ON─ POWER─ OFF
1
23
45
SOURCE 
						

							14
SETUP AND OPERATION
Inserting the Remote Control Batteries
1. Remove the battery compart-
ment cover by sliding the cover 
in the direction of the arrow.
2. Insert the supplied batteries tak-
ing note of the polarity (+/-) as 
shown here.
3. Replace the cover.
CAUTIONCAUTION
Only use AAA alkaline batteries.
Dispose used batteries according to local ordinance regulations. 
Remove the batteries when not using the projector for prolonged periods. 1.
2.
3. 
						

							15
Connecting Input Devices
A PC or notebook computer as well as video devices can be connected to the projector at the 
same time. Video devices include DVD, VCD, and VHS players, as well as movie camcorders , 
digital still cameras and high defi nition sources. Check the user manual of the connecting device 
to confi rm it has the appropriate output connector.
  
As a safety precaution, disconnect all power to the projector and connecting 
devices before making connections.  
						

							16
Starting and Shutting down the Projector
1. Remove the lens cover.
2. Connect the power cord to the projector. 
Connect the other end to a wall outlet.
3. Press the Power button. The Power LED 
on the projector turns on. Turn on the con-
nected devices.
4. The language selection screen appears 
(Initial setup only). Select the desired lan-
guage. 
1.  Press the cursor ▲▼ button until 
Language is highlighted. 
2.  Press the cursor ◄ ► or Menu button 
to confi rm the language, and close the 
OSD.
 
5. If more than one input device is connected, 
press the source button to search. 
6. Press the Power button to turn off the pro-
jector.  The Powering Down screen appears.
Note: Pressing the Power button again 
within fi ve (5) seconds cancels powering 
down the projector.
7. When the Power LED stops fl ashing, the 
projector goes on standby mode.
                
Do not unplug the power cord until the Power LED stops fl ashing, indicating 
the projector has cooled down. 
						

							17
Adjusting the Projector Level
Take note of the following when setting up the projector:
• The projector table or stand should be level and sturdy.
• Position the projector so that it is perpendicular to the screen.
• Be sure cables are not in the way or can cause the projector to be knocked over.
1. To raise the level of the projector, lift the 
projector and press the height-adjuster 
button [A]. 
The height adjuster drops down [B]. 
2. To lower the level of the projector, press 
the height-adjuster button and push 
down on the top of the projector.
3. To adjust the angle of the picture, turn 
the tilt adjuster right or left until the de-
sired angle has been achieved.
A
B 
						

							18
Adjusting the Focus and Zoom
1. Locate the image zoom and focus 
adjustment rings on the projector. Zoom   Focus
2. Use the image zoom control to resize the 
projected image and screen size.
3. Rotate the image focus control to sharpen 
the projected image. 
						

							19
ON-SCREEN DISPLAY (OSD) MENU SETTINGS
OSD Menu Controls
The projector has an OSD that lets you make image adjustments and change various settings. 
When the projector is turned on, any connected devices are detected. If the connected device is 
a PC, press the appropriate keys on the computer keyboard to switch the display output to the 
projector. (Check the user manual of the PC to determine the appropriate Fn key combination to 
change display output.)
Navigating the OSD
You can use the remote control cursor buttons or the buttons on the top of the projector to navigate 
and make changes to the OSD. The following illustration shows the corresponding buttons on the 
remote control and on the projector.
To open the OSD, press the 
Menu button. 
There are six menus. Press 
the cursor 
◄ ► button to move 
through the menus. 
Press the cursor 
▲▼ button to 
move up and down in a menu. 
Press 
◄ ► to change values for 
settings, and then press Enter
 
to confi rm the new setting.
Press Menu to close the OSD 
or leave a submenu. 1.
2.
3.
4.
5.
Depending on the video source not all items in the OSD are available. For ex-
ample, the Horizontal/Vertical Position items in the Setup menu can only be 
modifi ed when connected to a PC. Items that are not available cannot be ac-
cessed and are grayed out.  
						

							20
Setting the OSD Language
You may want to reference the OSD on your projector while reading this section. Set the OSD 
language to your preference before continuing. (The default language is English.) 
Press the Menu button. The Image menu appears.
Press the cursor ◄ ► button until Language is highlighted. 
Press the cursor ▲▼ button until the desired Language is highlighted. 
Press the Menu button to confi rm the language, and close the OSD. 1.
2.
3.
4.