Planar Pr2020 Projector User Manual

DLP® Projector – User’s Manual 
Setting an Access Password (Security Lock) 
You can use the four (arrow) buttons to set a password and prevent unauthorized use of the projec-
tor. When enabled, the password must be enter ed after you power on the projector. (See Navigating 
the OSD  on page  18 and Setting the OSD Language  on page 19 for help on using OSD menus.) 
Important: 
Keep the password in a safe place.  Without the password, you will not be able to use the projector. 
If you lose the password,...

DLP® Projector – User’s Manual 
5.  You can use the cursor buttons 
▲▼◄► 
either on keypad or IR remote control 
for password entry. You can use any 
combination including the same arrow 
five times, but not less than five. 
Press the cursor buttons in any order 
to set the password. Push the MENU 
button  to exit the  dialog box. 
 
 
6.  The password confirm menu appears 
when user presses the power-on key 
in case the  Security Lock is enabled. 
Enter the password in the order you 
set it at step 5....

DLP® Projector – User’s Manual 
Adjusting the Projector Level 
Take note of the following when setting up the projector: 
• The projector table or stand should be level and sturdy. 
•  Position the projector so that it is perpendicular to the screen. 
•  Ensure the cables are in a safe location. You could trip over them.  
 
1.  To raise the level of the projector, lift the projector  [A] and press the height-adjuster 
button [B] .  
The height adjuster drops down  [C].  
2.  To lower the level of the...

DLP® Projector – User’s Manual 
Adjusting the Focus and Keystone 
1.  Use the Image-focus  
control (on the projector 
only) to sharpen the 
projected image. 
 
2.  Use the KEYSTONE 
buttons (on the projec-
tor or the remote 
control) to correct im-
age-trapezoid (wider 
top or bottom)  
effect. 
 
Remote control and OSD panel 
 
3.  The keystone control  
appears on the display. 
 
 
– 16 –  

DLP® Projector – User’s Manual 
Adjusting the Volume 
1.  Press the Volume +/-   
buttons on the remote 
control.  
The volume control  
appears on the display. 
2.  Press the  Left or Right 
Cursor  buttons on the 
keypad to adjust  Volume 
+/-.  
 
 
 
 
 
3.  Press the  MUTE button to 
turn off the volume (This 
feature is available only 
on the remote). 
 
 
–  17  –  

DLP® Projector – User’s Manual 
– 18 – 
On-Screen Display (OSD) Menu Settings 
OSD Menu Controls 
The projector has an OSD that lets you make image adjustments and change various settings.  
Navigating the OSD 
You can use the remote control cursor buttons or the buttons on the top of the projector to navigate 
and make changes to the OSD. The following illust ration shows the corresponding buttons on the re-
mote control and on the projector. 
 
 
 
1.  To enter the OSD, press the  MENU button.  
2....

DLP® Projector – User’s Manual 
Setting the OSD Language 
Set the OSD language to your preference before continuing. 
1. Press the MENU button. Press the cursor  ◄► button to navigate to Installation I. 
 
2. Press the cursor ▲▼  button until Language is highlighted.  
 
3. Press the cursor ◄►  button until the language you want is highlighted.  
4. Press the MENU button twice to close the OSD.   
– 19  –  

DLP® Projector – User’s Manual 
OSD Menu Overview 
Use the following illustration to quickly find a setting or determine the range for a setting. 
 
 
 
– 20 –  

DLP® Projector – User’s Manual 
OSD Sub-Menu Overview 
 
– 21  –  

DLP® Projector – User’s Manual 
Image Menu  
Press the MENU button to open the OSD menu. Press the cursor  ◄► button to move to the  Image 
Menu. Press the cursor  ▲▼ button to move up and down in the  Image menu. Press  ◄► to change 
values for settings. 
 
Item Description 
Display Mode  Press the cursor ◄► button to set the Display Mode.  
Brilliant Color  Press the cursor ◄► button to adjust the Brilliant Color value. 
Brightness Press the cursor ◄► button to adjust the display brightness. 
Contrast...