Planar Pr3010 Projector User Manual

							User’s Manual 
– 4 – 
7.  VOL+/ 
Right cursor Increases volume 
Navigates and changes settings in the OSD 19 
8.  Auto  Optimizes image size, position, and resolution 
Navigates and changes settings in the OSD 
9.  Menu  Opens and exits the OSD 
10.  Source  Detects the input device 
11.  Power  Turns the projector on or off 
13  
						

							DLP® Projector – User’s Manual 
– 5 – 
Rear view 
 
ITEM LABEL DESCRIPTION SEE 
PAGE:
1.  Rear IR receiver  Receiver for IR signal from remote control 7 
2.  DVI-D 
(For PR5020 only) Connect a DVI-D cable (not supplied) from a computer 
3.  VGA IN  Connect a VGA cable (supplied)  from a computer 
4.  VGA OUT  Connect to a monitor (not supplied) 
5.  S-video  Connect the S-video cable (not supplied) from a video device 
6.  Video  Connect a composite video cable (supplied) from a video 
device. 
7.  Audio in-R  Connect the audio cable (supplied) from an audio input device. 
8.  Audio in-L  Connect the audio cable (supplied) from an audio input device. 
9.  Audio-in  Connect an audio cable(supplied) from the computer’s audio-out 
connector. 
10.  Audio-out Audio loop-thru 
11.  USB  Connect the USB cable (supplied) from a computer 
12.  RS-232 
(For PR5020 only) Installation control  
11 
13.  Power  Connect the power cord (supplied) 13  
						

							User’s Manual 
– 6 – 
14.  Security Lock  Secure to permanent object with a Kensington® Lock  
system 37 
 
Note: 
If your video equipment has both S-video and RCA jacks (composite video) connect to the S-video 
connector.  
S-video provides a better quality signal. 
Bottom view 
 
 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  Ceiling support holes  Contact your dealer for information on mounting 
the projector on a ceiling.  
2.  Height adjuster button  Push to release height adjuster 
3.  Height adjuster  Adjuster drops down when adjuster button is 
pushed 
4.  Tilt adjuster  Adjust angle of the picture 
16 
  
						

							DLP® Projector – User’s Manual 
– 7 – 
Remote Control Parts 
 
Important: 
1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency 
fluorescent lights can disrupt remote control operation. 
 
2. Be sure nothing obstructs the path between the remote control and the projector. If the path 
between the remote control and the projector is obstructed, you can bounce the signal off certain 
reflective surfaces such as projector screens. 
 
3. The buttons and keys on the projector have the same functions as the corresponding buttons on 
the remote control. This user’s manual describes the functions based on the remote control.  
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  IR transmitter  Transmits signals to projector 
2.  Status LED  Lights when the remote control is used 
3.  Laser  Press to operate the on-screen pointer 
4.  Up  Up arrow when connected through USB to a PC 
5.  Right  Right arrow when connected through USB to a PC 
6.  Down  Down arrow when connected through USB to a PC  
						

							User’s Manual 
– 8 – 
ITEM LABEL DESCRIPTION SEE PAGE: 
7.  Page Down  Page down when connected through USB to a PC 
8.  Up cursor  
9.  Right cursor  
10.  Down cursor Navigates and changes settings in the OSD
  19 
11.  Volume +/-  Adjusts volume 17 
12.  Mute  Mutes the built-in speaker 
13.  Zoom+  Zoom in  
14.  Zoom- Zoom out 
15.  Freeze   Freeze/unfreezes the on-screen picture 
16.  Blank  Makes the screen blank 
17.  Source  Detects the input device 
18.  Auto  Auto adjustment for phase, tracking, size, position 
19.  Menu  Opens the OSD  19 
20.  Status Opens the OSD Status menu (the menu only opens 
when an input device is detected) 32 
21.  Keystone 
top/bottom Corrects image-trapezoid (wider top/bottom) effect 17 
22.  Left cursor  Navigates and changes settings in the OSD  
23.  Enter  Changes settings in the OSD 
19 
24.  Page Up  Page up when connected through USB to a PC 
25.  Left  Left arrow when connected through USB to a PC 
26.  Enter  Enter key when connected through USB to a PC 
27.  Power   Turns the projector on or off 13 
28.  Laser  Use as on-screen pointer. DO NOT POINT IN EYES. 
Note: 
The remote control can only interface with a computer when connected to the computer through a 
USB cable connection. The computer cable connects a computer to the projector for display 
purposes only.  
						

							DLP® Projector – User’s Manual 
– 9 – 
Remote Control Operating Range 
The remote control uses infrared transmission to control the projector. It is not necessary to point the 
remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or 
the rear of the projector, the remote will function well within a radius of about 10 meters (33 feet) and 
30 degrees above or below the projector level. If the projector does not respond to the remote control, 
move a little closer.   
Projector and Remote Control Buttons 
The projector can be operated using the remote control or the buttons on the top of the projector. All 
operations can be carried out with the remote control; however the buttons on the projector are 
limited in use. The following illustration shows the corresponding buttons on the remote control and 
on the projector. 
 
Some buttons on the projector have two functions. For example, item 10/13 on the projector functions 
both keystone button and as the up cursor key in OSD menus. 
 
  
						

							 
– 10 – 
 
SETUP AND OPERATION 
Inserting the Remote Control Batteries 
1.  Remove the battery compartment cover 
by sliding the cover in the direction of 
the arrow. 
 
2.  Insert the supplied batteries taking note 
of the polarity (+/-) as shown here. 
 
3.  Replace the cover. 
 
 
Caution: 
1. Only use AAA alkaline batteries. 
 
2. Dispose of used batteries according to local ordinance regulations.  
 
3. Remove the batteries when not using the projector for prolonged periods. 
  
						

							DLP® Projector – User’s Manual 
– 11 – 
Connecting Input Devices 
A PC or notebook computer as well as video devices can be connected to the projector at the same 
time. Video devices include DVD, VCD, and VHS players, as well as movie camcorders and digital 
still cameras. Check the user manual of the connecting device to confirm it has the appropriate output 
connector.  
 
ITEM LABEL DESCRIPTION 
A 
Rear IR  Receiver for IR signal from remote control. 
B 
DVI-D 
(For PR5020 only)  Connect DVI-D cable (not supplied) from a computer. 
C 
VGA in  Connect a VGA cable (supplied) from a computer. 
D 
VGA out  Connect a VGA cable (not supplied) to a monitor. 
E 
S-video  Connect S-video cable (not supplied) from a video device. 
F 
Video  Connect a composite video cable (supplied) from a video device. 
G 
Audio in-R  Connect the audio cable (supplied) from an audio input device. 
H 
Audio in-L  Connect the audio cable (supplied) from an audio input device. 
I 
Audio-in  Connect an audio cable (supplied) from the computer’s audio-out 
connector. 
 
Audio-out Audio loop-thru 
 
USB  Connect the supplied USB cable (supplied) from a computer for USB 
mouse function and firmware upgrades. 
 
RS-232 
(For PR5020 only) Reserved for installation control.  
						

							User’s Manual 
– 12 – 
 
Warning: 
As a safety precaution, disconnect all power to the projector and connecting devices before making 
connections.  
						

							DLP® Projector – User’s Manual 
– 13 – 
Starting and Shutting down the Projector 
1.  Slide the lens cover. 
2.  Connect the power cord to the projector [A]  
Connect the other end to a wall outlet.  
Switch [B] from on (O) to off (

{

   
3.  The POWER and READY LEDs on the 
projector turn on.                                            
Turn on the connected devices. 
 
4.  Ensure the Ready LED is on a steady (not 
flashing) orange and then press the Power 
button to turn on the projector.  
 
The projector splash screen displays and 
connected devices are detected. 
If the connected device is a PC, press the 
appropriate keys on the computer keyboard to 
switch the display output to the projector. 
(Check the user manual of the PC to 
determine the appropriate Fn key combination 
to change display output.) 
 
See “Setting an Access Password (Security 
Lock)” on page 15 if Security Lock is 
enabled. 
  
5.  If more than one input device is connected, 
press the Source button repeatedly to switch 
among devices. 
(DVD and HDTV are supported through the 
VGA connector.) 
 
6.  To turn off the projector, press the Power 
button. The projector prepares for shutdown 
and a “Wait a moment please…” message 
appears.