Planar Pr5021 Projector User Manual

DLP® Projector – User’s Manual 
Top view—On-screen Display (OSD) buttons and LEDs 
 
Item Label Description See page:
1.   (POWER) Turns the projector On or Off  12
2.  SOURCE Detects the input device 11
3.  AUTO Optimizes image size, position, and resolution 
4.  ▲ (Up cursor) / 
KEYSTONE Navigates and changes settings in the OSD 
Quick Menu – For Keystone 
5.  ►  (Right cursor) / VOL. Navigates and changes settings in the OSD 
Quick Menu – For Volume 19
On System over temperature 
6.  OVER TEMP LED...

DLP® Projector – User’s Manual 
Rear view 
123456789
 
 
Item Label Description See page: 
1.  12AC IN Connect the power cable 
Connect the USB cable from a computer  
(service only) 2.   (USB) 
3.  S-video Connect the S-Video cable from a video device 
4.  Video Connect the video cable from a video device  
5.  Audio-in Connect the audio cable from the input device  
– 4 – 
6.  RGB IN Connect the RGB cable from a computer and 
components 
11
7.  RGB OUT Connect the RGB cable to a display 
Connect...

DLP® Projector – User’s Manual 
Bottom view 
 
Item Label Description See page: 
Contact your dealer for information on mounting the projector on a 
ceiling 1.  Ceiling support holes 
2.  16Tilt adjustor  Rotate adjuster lever to adjust angle position.  
343.  Lamp cover Remove when changing the lamp. 
Adjuster drops down when adjuster button is 
pushed. 4.  Height adjustor 
16
5.  Height adjustor button Push to release adjustor. 
 
Note: 
When installing, ensure that you use only UL Listed ceiling...

DLP® Projector – User’s Manual 
Remote Control Parts 
 
Important: 
1. Avoid using the projector with  bright fluorescent lighting turned  on. Certain high-frequency fluores-
cent lights can disrupt remote control operation. 
 
2. Be sure nothing obstructs the path between the remo te control and the projector. If the path between 
the remote control and the projecto r is obstructed, you can bounce the signal off certain reflective sur-
faces such as projector screens. 
 
3. The buttons and keys on the...

DLP® Projector – User’s Manual 
— 7 — 
 
Item Label Description See page:
1.  IR transmitter Transmits signals to projector  
2.  Status LED Lights when the remote control is used 
3.  Laser Press to operate the on-screen pointer 
4.  Up Up arrow when connected through USB to a PC   
5.  Right Right arrow when connected through USB to a PC 
6.  Down Down arrow when connected through USB to a PC 
7.  Page Down Page down when connected through USB to a PC 
8.  Up cursor 
9.  Right cursor 
10.  Down cursor...

DLP® Projector – User’s Manual 
– 8 – 
Item Label Description See page:
25.  Left Left arrow when connected through USB to a PC 
26.  Enter Enter key when connected through USB to a PC 
19
27.  Power Turns the projector on or off 12
28.  Laser Use as on-screen pointer. DO NOT POINT IN EYES. 
  

DLP® Projector – User’s Manual 
Remote Control Operating Range 
The remote control uses infrared transmission to control the projector. It is not necessary to point the 
remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or 
the rear of the projector, the re mote will function well within a radi us of about 7 meters (23 feet) and 
15 degrees above or below the projector level. If the pr ojector does not respond to the remote control, 
move a little...

 – 10  –
 
Setup and Operation 
Inserting the Remote  Control Batteries 
1.  Remove the battery compartment 
cover by sliding the cover in the di-
rection of the arrow. 
 
2.  Insert the battery with the positive 
side facing up. 
 
3.  Replace the cover. 
 
 
Caution: 
1. Only use AAA battery (Alkali ne batteries are recommended). 
 
2. Dispose of used batteries accordi ng to local ordinance regulations.  
 
3. Remove the battery when not using  the projector for prolonged periods. 
 
 
  

DLP® Projector – User’s Manual 
 
Connecting Input Devices 
A PC or notebook computer and video devices can be connected to the projector at the same time. Video 
devices include DVD, VCD, and VHS players, as well as movie camcorders and digital still cameras. 
Check the user manual of the connecting device to  confirm it has the appropriate output connector.  
A
BC D E G
F
 
Item Label Description 
A
–  11  – 
 
 (USB) Connect the USB cable from a computer (service only). 
B 
S-video Connect the...

DLP® Projector – User’s Manual 
Starting and Shutting down the Projector 
1.  Connect the power cord to the pro-
jector. Connect the other end to a 
wall outlet. 
The 
 POWER  and READY  LEDs 
on the projector light. 
2.  
 Turn on the connected devices. 
3.  Ensure the READY LED displays a 
solid orange and not a flashing or-
ange. Then press the 
  POWER  
button to turn on the projector.  
 
The projector splash screen displays 
and connected devices are de-
tected. 
 
See 
Setting an Access Password...