Plus He 3100 Projector User Manual

							E – 41
3
Install the new lamp cartridge.
qInstall the new lamp cartridge in the direction as shown
in the drawing.
Plug
4
Reinstall the lamp cover.
qInsert the lamp cover until the catches fit in the grooves.
wTighten the lamp cover screw. wTighten the lamp cartridge screw.
(Put down the handle of the lamp cartridge.)
Groove
5
Reset the lamp usage hours to zero.
From the menu, select [Info.] → [Lamp Timer Reset] and then reset the lamp usage hours.
See Resetting the Lamp Timer on page E-37.
NOTE: When the projector lamp has exceeded 1100 hours of operation, the projector will not turn on. This means you cannot reset the lamp usage on the
menu. Should this happen, press SOURCE and ASPECT on the projector cabinet for at least of 5 seconds at the same time when the projector is in standby
mode. When the lamp usage is reset, the STATUS indicator goes off.
 [This completes the lamp replacement.] 
						

							E – 42
Cleaning a Soiled Projector Main Unit
* Wipe with a lint-free, soft, dry cloth.
When very dirty, wipe with a cloth that has been moistened with a diluted neutral detergent, then finish with a dry cloth. If a
chemically-treated cloth is going to be used, please follow any written warnings.
* Do not wipe with thinner, benzene, or other solvents. Doing so could cause them to undergo qualitative changes or the coatings
may peel, etc.
* When removing the dust of the outflow and intake holes, use the brush attachment on a vacuum cleaner to clean out the dust.
Avoid using the vacuum directly without attaching the adapter as well as the use of a nozzle adapter.
* Do not scratch or otherwise hit the projector body with your nails or other hard object, since this will cause scratches.
Dirty Lens
The lens surface has been treated with a special coating. Consult your PLUS dealer for cleaning.
Dust of the Intake and Outflow Holes
Dust that collects in the intake and outflow holes will obstruct the ventilation and cause the internal temperature to rise which could
cause damage. Clean this area carefully. As a guideline, clean at least every 100 hours.
Cleaning
Attention!
* Be certain to disconnect the power plug from the power outlet before cleaning.
* Do not spray or otherwise expose the projector, lens, or screen to volatile substances such as insecticides. Doing so
could cause them to undergo qualitative changes or the coatings may peel, etc.
POWER
ON OFF
* Switch off the power with the ON/STANDBY
button and check that the POWER/ 
 indica-
tor has changed to a steadily lit orange, then
switch off the main power with the POWER
switch of the main unit. Finally, disconnect the
power cord.
* Clean out the holes from the outside using a
vacuum cleaner. Use the brush adapter of the
vacuum cleaner to do this. Avoid using the
vacuum directly without attaching the adapter
as well as the use of a nozzle adapter.
Cleaning the Inside of the Projector
Cleaning of the inside of the projector is required about once a year. Failure to clean over a long period while dust has collected
inside the projector could cause a fire or breakdown. Do not clean the inside of the projector by yourself. Be sure to consult your
PLUS dealer.
Brush adapter 
						

							E – 43
Specifications
Model Name HE-3100
Display Method Single Chip Digital Micromirror Device (DMD
TM)
DMD Panel 0.7
508,800 pixels (848 x 600)
Lens Manual focus
F=3.0 f=23mm
Lamp 130W High Performance Compact Lamp
Image Size Min. 36 (Throw distance 1.2m / 3.9 feet)  Max. 200 (Throw distance 6.9m / 22.6 feet)
Color Reproduction Full color, 16.7 million colors simultaneously
Light Output 450 ANSI lumens (normally white)
Contrast Ratio 700:1 (Full on/off)
Scanning Frequency Horizontal :15 - 85 kHz
Vertical :50 - 85 Hz
Functions Focus(Manual), Projection angle, Source select (Video/S-Video/YcbCr/DVI), Aspect,
Standby On/Off, Projection orientation, Digital keystone correction, Brightness, Contrast, Color,
Tint*
1, Sharpness, Color temperature, Gamma correction
Digital RGB Input T.M.D.S-compliant (single link only)
Input Terminal DVI-D 24 pin x 1
RGB Signal VGA (640 x 480) enlarged/ SVGA (800 x 600) full, XGA (1024 x 768) compressed
Component Input Component
Y (luminance signal) : 1.0Vp-p/75Ω, Cb, Cr : 0.7Vp-p/75Ω
RCA x 3
Video Input NTSC 3.58, NTSC 4.43, PAL, PAL N, PAL M, PAL60, SECAM
Composite : 1.0Vp-p/75Ω
S-Video : Y (1.0Vp-p/75Ω), C (0.286Vp-p/75Ω)
RCA x 1,  4-pin mini DIN x 1
Horizontal Resolution NTSC: 400 lines or more
Environment Operating temperature: 5 - 35˚C / 41 - 95˚F, 30 - 85% humidity (no-condensing)
Storage temperature: -10 - 60˚C / 14 - 140˚F, 10 - 85% humidity (no-condensing)
Power Requirement 100 - 240V AC, 50 / 60Hz
Power Consumption 200 W (STANDBY 18W)
Dimensions 235 (W) x 91 (H) x 198 (D) mm (not including protrusion)
9.3 (W) x 3.6 (H) x 7.8 (D) inch (not including protrusion)
Weight 2.0kg / 4.4 lbs
Regulations UL Approved (UL 6500, CSA-E60065)
Meets FCC Class B requirements
Meets EMC Directive (EN55022, EN55024)
Meets Low Voltage Directive (EN60065)
*1: Not available on SECAM signal
The specifications are subject to change without notice.
Digital Micromirror Device
TM (DMDTM) by Texas Instruments 
						

							E – 44
Main Unit External View
DVI-D COMPONENT
CTRL
S-VIDEOVIDEOY             Cb            Cr
91 mm / 3.6 inch
235 mm / 9.3 inch
174 mm / 6.9 inch
198 mm / 7.8 inch