Plus Projector U5 232 User Manual

E-20
VIDEOS-VIDEO
Connecting Personal Computers and Video Equipment
Connections with Composite Signals
Video Equipment with VIDEO Connectors
•The input setting of the VIDEO connector has been set to “Auto” at the factory; however, if the projector does not project, please
change the input setting to “Your Country’s Television Broadcast System” using the menu sequence of [Setup] → [Input Format]
→ [Video].
See “Input Format” on Page E-56.
Video Equipment with S-VIDEO Connectors
•Make the connection to the...

E-21
CrCbY
Pr Pb YCOMPONENT
COMPONENT
Connecting Personal Computers and Video Equipment
Connections with Component Signals
When the Video Equipment Has a YCbCr Connector or YPbPr Connector
•The projector has been set to “Auto” at the factory; however, if it does not project, please change the input setting to “Compo-
nent” using the menu sequence of [Setup] → [Input Format] → [RGB].
See “Input Format” on Page E-56.
•When projecting the YCbCr signal or YPbPr signal, if the color of the overall image...

E-22
Connecting Personal Computers and Video Equipment
Connections with the AUDIO Jack
* Make the connection to the projector’s AUDIO jack using the supplied audio cable. When the audio jack of the equipment that
is to be connected is of the RCA phono type, make connection via the supplied audio conversion cable.
* The built-in speaker of the projector provides monaural audio. To enjoy convincing audio reproduction, please connect the
audio output of the video equipment to your audio system.
* The...

E-23
Power Cable Connections and Switching the Power On/Off
STAN
D
BY S
TAT
U
SSTANDBY
AUTO
SOURCE
RGB
S VIDEO
VIDEO
AUDIO
MOUSE
PC CONTROL
There is an order in which the power cable is connected and the power is switched on/off.
Operating
1Connect the AC IN connector of the projector and the power outlet using the supplied power cable.The STANDBY indicator will light in amber, and the unit will enter the standby mode.
Firmly plug in all the way.
To wall outlet
2Switch on the projector powerPress the...

E-24
When [Menu Language Select] is Displayed Upon Switching On the Power
The first time the power is switched on after purchase, [Menu Lan-
guage Select] will be displayed. Follow the procedure described be-
low and select the display language of the projector.
If the image is blurred, turn the focus ring counterclockwise or clock-
wise to focus it. See Page E-27.
1Press the SELECT 
 buttons of the Remote con-
trol and align the deep blue cursor with [English].
Cursor
2Press the ENTER button to set....

E-25
Power Cable Connections and Switching the Power On/Off
Finishing
1Switch off the power of the connected equip-
ment
2Switch off the power of the projector
Press the STANDBY button.
The [Power Off] display appears.
When the level gauge reaches maximum, the projection screen
will go off (in about 5 seconds) and the projector will enter the
power-off operation.
Note
* The operation can be cancelled by pressing a button other than
the STANDBY button.
* One more press of the STANDBY button will switch...

E-26
Adjustment of the Projection Screen
Switch on the power of the connected equipment and make the adjustments with the video signal being input to the
projector.
Adjustment of the Projection Screen
2
(2)
(1)(3)
(4)
(5)(3)(4)
Turn the zoom ring to adjust the screen size of the projection image.Adjust the image to match the desired screen size. When outside of the adjustment range, move the projector to the rear or
forward.1
Applicable Projector: U5-232/U5-132/U5-112
Zoom ring
Adjust the projection...

E-27
Adjustment of the Projection Screen
(
1)
ST
ANDBY STATUSS
TA
N
D
B
Y
A
U
T
O
S
O
U
R
C
E
(
1)
(
2)
3Turn the focus ring and adjust the focus of the screen
Focus ring
Making Adjustments with the Adjusters
While viewing the projection image, (1) press and hold
the adjuster buttons located at the left and right and, (2)
raise the projector to align the image with the screen, then
release your fingers.
Turn the left and right adjusters for fine adjustment.
Adjust so that there is no shaking of the...

E-28
General Operation
This section describes the use of direct operation with the main unit or remote control buttons.
For information about operation using the menu, see “Menu Operation Method” on Page E-40 and the various items on
Pages E-47 to E-60.
Input Selection
This operation selects the input signal to be projected.
Main unit operation: Press the SOURCE button.
(It will not function while the menu or the quick menu is displayed.)
When Auto Source is On
Whenever the SOURCE button is pressed, the...

E-29
General Operation
Selection of Aspect Ratio
This function selects horizontal and vertical picture proportions of the input
signal.
Press the ASPECT button while viewing the projected image and select the
aspect ratio.
Personal Computer Signal
Each press of the ASPECT button advances the selection one step in the se-
quence of Auto → Direct → Real, and then repeats.
Auto ............ Automatically enlarges or reduces the image to project a full screen in a ratio
of 4:3
Direct .......... Maintains the...