Plus Projector U7 132 User Manual

							E-61
Replacing the Lamp Cartridge
•The lamp that is used as a light source in the projector has a limited service life. The rated service life of the lamp is
about 2000 hours (when used in normal mode only). This could be shortened depending on conditions of use and
other factors.
Note that lamp life will be extended when the projector is often used in Eco mode. (The rated service life of the lamp
means the average value of lamp life for lamps that have been manufactured over a long period, and it is derived from
test conditions at this company.)
•When the life of the lamp is exceeded, the STATUS indicator lights a steady red and the message [Replace the Lamp
Cartridge] is displayed on the screen. When this occurs, it is time to replace the lamp cartridge. Please make the
replacement following the procedure below.
•If the projector is used another 100 hours after the lamp’s service life is reached, the power is set to the standby mode
and no longer turns on.
•Contact a store that sells the U7-132/U7-137 for a replacement lamp. Indicate you need a U7-300 replacement lamp for
the U7-132/U7-137 (order code 28-057).
CAUTION
• Replacement of the lamp cartridge is performed after switching off the power, waiting for the cooling fan to stop,
disconnecting the power plug from the power outlet, and then leaving the projector for about 60 minutes before
replacement is started. Replacement of the lamp cartridge during operation or immediately after operation stops will
cause burns because of the high temperature.
• Do not remove any screws other than those specified.
• Do not touch the lamp with bare hands. Doing so could shorten the life of the lamp.
• If lamp has reached the end of its usable life, the lamp bulb may shatter. When this happens, an explosive sound can
be heard and pieces of glass may be scattered in the lamp cartridge. Do not touch them as the pieces of glass may
cause injury. If this happens, contact your dealer or the store the projector was purchased. 
						

							E-62
Replacing the Lamp Cartridge
1Unplug the power cord.
2Turn the projector upside-down.
3Remove the lamp cover.
(1) Turn the lamp cover’s set screw counterclockwise and
loosen until the screw turns freely. (The screw does
not come off.)(2) Open the lamp cover a little, then pull it in the direc-
tion of the arrow and remove it.
4Remove the lamp cartridge.
(1) Turn the lamp cartridge’s two set screws counter-
clockwise and loosen them until the screws turn freely.
(The screws do not come off.)(2) Grasp the lamp cartridge’s handle and pull upward
to remove the lamp cartridge. 
						

							E-63
Replacing the Lamp Cartridge
5Mount the new lamp cartridge.
(1) Place the lamp cartridge with its socket facing to the
left and push it in slowly.
(Line it up with the screw holes in the projector.)
Note:
After reaching the lamp service life, if the lamp is used for more than another 100 hours, it will not be possible to switch on the power. Should
this happen, while the projector is in the standby mode, simultaneously holding down the projector’s SOURCE button and AUTO button for
more than 5 seconds will clear the lamp timer. Checking that the STATUS indicator is out will show that the lamp timer has been cleared.
Contact a store that sells the U7-132/U7-137 for a replacement lamp. Indicate you need a U7-300 replacement lamp for the U7-132/U7-137
(order code 28-057).
(2) Turn the two lamp cartridge screws clockwise to
tighten them.
6Mount the lamp cover.
(1) Set the tip of the lamp cover in place, then close the
lamp cover.(2) Turn the lamp cover’s screw clockwise to tighten it.
7Reset the Lamp Timer.
Connect the power cable, switch on the power, and then reset.
Select [Info.] → [Lamp Timer Reset] on the menu and press the ENTER button. There is a change to the initialization
verification display. Press the ENTER button again. See “Lamp Timer Reset” on Page E-56. 
						

							E-64
Specifications
ModelU7-132/U7-137
Optical
Method of projection : DLP™ (single chip DMD)
DMD 0.7 inches 1024768 dots
Lamp 300 W high pressure mercury lamp
Projection lens : Manual zoom (1.2), Manual focus F = 2.4 – 2.6, f = 26.5 – 31.8 mm
Image size Minimum 27 inch (at projection distance of 1.20 m / 3.9 feet  telephoto)
Maximum 300 inch (at projection distance of 11.5 m / 37.7 feet wide)
Light Output 3000 lumens (in the “Dynamic” mode)
Contrast Ratio 2000:1 (Full on/off)
Electrical
Inputs Video (NTSC3.58/NTSC4.43/PAL/PAL-N/PAL-M/PAL60/SECAM)
RGB (Horizontal :15 to 80 kHz, Vertical  50 to 85 Hz)
Projector control U7-132 :
RS-232C
U7-137 :
RS-232C or Telnet via a LAN (using PLUS projector control commands)
Color Reproduction Full color (16,770,000 colors)
Resolution VGA (640480) expansion/true, S-VGA (800600) expansion/true
XGA (1024768) true, S-XGA (12801024) compression
Input Current 4.3 A
Power Requirement 100 - 240 V AC, 50/60 Hz
Power Consumption 430 watts (380 watts in eco mode)
Mechanical
Dimensions Excluding Stand 258 mm (W)83 mm (H)320 mm (D)
10.2 in. (W)2.9 in. (H)3.3 in. (D)
Weight U7-132 :
3.0 kg / 6.6 lbs
U7-137 :
3.1 kg / 6.8 lbs
Operational Temperatures Data projector: 5° to 35°C (41° to 95°F), 30 to 85% humidity
• Specifications and design are subject to change without notice. 
						

							E-65
Table of Supported Frequencies
The projector automatically identifies the signal input from the computer and selects the optimum resolution as shown on the table
below.
Manual adjustments may be required for some input signals. See “Picture Adj. / Fine Picture / H Position / V Position” on page E-
44, 45.
: Supported frequency
: Not supported frequency * The projector does not support the ADC connector on Apple Macintosh.
The display resolution is 1024768 dots. When displaying a signal with resolutions other than 1024768 dots such as 12801024,
sizes of characters or lines may be uneven.
VIDEO(NTSC)
VIDEO(PAL/SECAM)
PC/AT
VESA
Apple Macintosh
HDTV (1080i)
(720p)
EDTV (576p)
(480p)
SDTV (576i)
(480i)

640350
640400
720350
720400
640350
640400
720400
640480
640480
640480
640480
800600
800600
800600
800600
800600
1024768
1024768
1024768
1024768
12801024
640480
823624
1024768
1152870
19201080
19201080
1280720
720576
720480
720576
72048015.734
15.625
31.5
31.5
31.5
31.5
37.9
37.9
37.9
31.5
37.9
37.5
43.3
35.2
37.9
46.9
48.1
53.7
48.4
56.5
60.0
68.7
64.0
35.0
49.7
60.2
68.7
33.8
28.1
45.0
31.3
31.5
31.3
31.560.0
50.0
70.1
70.1
70.0
70.0
85.1
85.1
85.0
60.0
72.8
75.0
85.0
56.3
60.3
75.0
72.2
85.1
60.0
70.1
75.0
85.0
60.0
66.7
74.5
74.9
75.1
60.0
50.0
60.0
50.0
60.0
50.0
60.0





































































































































SignalResolution VideoFrequencyHorizonral (kHz)Vertical (Hz)ComponentDigital Analog 
						

							E-66
MENU
PRESS
TO OPENPRESS
TO OPEN SOURCESTANDBY STATUS
AUTO
QUICK
MENU
Cabinet Dimensions
Unit: mm (inch) 258 (10.2)
83 (3.3)320 (12.6) 
						

							2005