Plus Projector V 339 User Manual

E-10
Names of the Remote Control Parts
RGB
VIDEO
FREEZE
MUTEECO AUTO
ASPECT
TIMER VOL KSTN ZOOMCANCEL QUICKMENU
ENTER
Q
STANDBY
1234
Infrared transmitter [E-11]
VOL button [E-27]
(Volume adjustment) STANDBY button [E-19, 21]
This button is used to switch ON
the power and set the unit to the
STANDBY mode.
AUTO button [E-24]
(Automatic adjustment of the RGB
moving image) Buttons used for menu operations
[E-33]
The 
, ,  and  buttons are
the select (
, ,  and ) buttons.
FREEZE button [E-26]
(Freezes...

E-11
Using the remote control for the first time
The battery compartment is fitted with a transportation insulation sheet at the time of shipping. Pull
out the sheet and remove it. The remote control is now ready for use.
Replacement Method
1(A) With the knob pressed to
the right side, (B) draw out the
battery case.2Remove the old battery and in-
stall a new button battery with (+)
side facing upward in the battery
holder.3Insert the battery holder into the re-
mote control and push in until the
battery...

E-12
The Procedure Up to Projecting to the Screen
Perform setup adjustments in the following order.
1Position the projectorDetermine the locations to set up the screen and the projector.
See “Placement Guide” on Page E-13.
2Connect the video equipment and personal computer
Connect your equipment to the projector.
When making connections with the personal computer’s RGB connector, see “Connections with
Personal Computer” on Page E-14.
When making connections with the video equipment’s video connector or...

E-13
Placement Guide
•Use this information as a guide to find out about the screen size when the projector is placed at a certain location, or
to find out the approximate size of a screen that will be required.
•The projection distance over which focussing is adjustable is 1.20 m (3.9 feet) to 14.17 m (46.50 feet). The projector
should be placed within this range.
* There is a tolerance of ±5% due to design values.
* This table uses the lens apex and lens center as references and requires that the...

E-14
Connecting Personal Computers and Video Equipment
Connecting this unit with a personal computer permits presentation data to be projected as a large screen display at
conferences, lectures, and on other occasions. Furthermore, connecting this unit to a DVD player or other video equip-
ment source in combination with an audio/video amplifier and speaker system will allow you to enjoy convincing home
theater.
MONITOR OUT
Personal
computer
RGB signal cable (Supplied item)
Note:
* Before making...

E-15
Connecting Personal Computers and Video Equipment
To Output the External Output Signal of a Notebook Computer
When projection will be with a notebook computer connected, knowledge will be required for the cable connection and notebook
computer startup procedure as well as the operation that follows notebook startup. Please consult the instruction manual of your
notebook computer or the on-line help while performing the following procedure.
1Check whether a signal is being sent from the notebook...

E-16
VIDEOS-VIDEO
Connecting Personal Computers and Video Equipment
Connections with Composite Signals
Video Equipment with VIDEO Connectors
•Connect to the projector’s VIDEO connector using a commercially available video cable. Please attach the supplied ferrite core
to the video cable as described below.
•The input setting of the VIDEO connector has been set to “Auto” at the factory; however, if the projector does not project, please
change the input setting to “Your Country’s Television Broadcast...

E-17
CrCbY
Pr Pb YCOMPONENT
COMPONENT
Connecting Personal Computers and Video Equipment
Connections with Component Signals
When the Video Equipment Has a YCbCr Connector or YPbPr Connector
•The projector has been set to “Auto” at the factory; however, if it does not project, please change the input setting to “Compo-
nent” using the menu sequence of [Setup] → [Input Format] → [RGB].
See “Input Format” on Page E-49.
•When projecting the YCbCr signal or YPbPr signal, if the color of the overall image...

E-18
R L
AUDIO OUT
Connecting Personal Computers and Video Equipment
Connections with the AUDIO Jack
* Connect to the projector’s AUDIO jack using a commercially available audio cable. If the other device has an RCA phono type
audio jack, connect via a commercially available audio converter cable. Please attach the supplied ferrite core to the audio
cable as described below.
* The built-in speaker of the projector provides monaural audio. To enjoy convincing audio reproduction, please connect the
audio...

E-19
Power Cable Connections and Switching the Power On/Off
There is an order in which the power cable is connected and the power is switched on/off.
Note:
•When the power plug will be unplugged from the power outlet, please place the projector near the power outlet so that it may be reached
easily.
•Press the STANDBY button after the STANDBY indicator is lit in amber.
STANDBY
STATUS
MENU
AUDIO MOUSERGBS-VIDEOVIDEO
SOURCEAUTO
DCMFirmly plug in all the
way.
To wall outlet
Operating
3Switch on the...