Pocket Radio Sangean DT 210 LV Operating Instruction

							DT-210/L/V
Operating instruction
Mode d’emploi
Instruccions de manejo
Gebruiksaanwijzing
BedienungsanleitungGB
F
E
NL
D 
						

							1 
						

							    2   Controls
   Stereo/Mono/Speaker switch
   Memory button
   Tuning Up/Down
   Earphones Jack
   Volume Control
   Power switch
   Display
   Memory Recall
   DBB (Deep Bass Boost) selection
   Band selector
   Belt Clip holder
   Lock switch
   Battery compartment
   Belt Clip
  Display
   Waveband indicator
   DBB on
   Key lock indicator
   Low battery indicator
   Frequency display
   Memory preset
   Stereo indicator
   90 minutes auto shut off indicator1235791113144681012AHEFBDCGGB 
						

							3  Installing batteries
1. Position the radio face down.
2. Press the catch and slide in the direction
    of the mark.
3. Lift up the battery cover and insert
    1xUM-4 (AAA) size on each side of
     battery compartment. Make sure the
     batteries are positioned in accordance
     with the diagram indicated.
4. Replace the battery cover.
Battery replacement
The battery indicator        will appear and
flash in the display when the batteries are in
need of replacement . After removing the
batteries, you have approximately 3 minutes
to replace the batteries after which the
preset memory information will be lost.
  Operating the radio 
						

							GB
    4   Search tuning
1. Switch on the radio by pressing the Power
    button.
Note:
The radio is originally set to be 90 minutes
auto shut off after Power is switched on
(        symbol will appear on the display).
If you don’t need this feature, press Power
button for more than 2 seconds until symbol
removed from the display.
2. Select the required waveband by
    repeatedly pressing the Band button.
    On FM and TV band (DT-210V only ),
    connect the supplied earphones as the
    antenna or the wire antenna. On AM(MW)
    and LW band (DT-210L), rotate the radio
    for best reception.
3. Press and hold down either the Tuning Up
    or Down buttons until frequency in the
    display begins to change rapidly.
    Release the button.
4. The radio will scan the selected waveband,
    stopping each time if finds a station of
    sufficient strength. Adjust the volume
    control to the required level. 
						

							5  Manual tuning
1. Switch on the radio by pressing the Power
    button.
2. Select the required waveband and connect
    the supplied earphones or wire antenna for
    FM and TV band (DT-210V) listening.
    On AM(MW) or LW band (DT-210L),
    rotate the radio for best reception.
3. A single press on either the Tuning Up/
    Down will change the frequency up or
    down. Adjust the volume control to the
    required level.
  Presetting stations
You may store up to 15 stations on FM band
and 10 stations on AM (MW) band for DT-210
(10 stations each on AM/FM/TV band for
DT-210V and 10 stations each on AM(MW)/
FM/LW band for DT-210L) .
1. Tune into the required stations using one of
    the tuning methods previously described.
2. To store the station, press MEMO button,
   display will flash M and the suggested
   memory location. Press MEMO button
   again to finalize the station presetting.
   During the M and suggested memory
   location are flashing, you may use either
   Tuning Up or Down to change the memory
   location to edit your memory program then
   press MEMO button again to finalize the
   presetting. 
						

							    6GB   Recalling a preset station
1. Switch on the radio.
2. Press RECALL button and Tuning Up/
    Down to recall required preset station
    Display will flash preset station.
3. Press RECALL button again, once the
    required preset station is found.
  Lock Switch
The lock switch located on the rear cabinet is
used to prevent unintentional operation.
1. Slide the lock switch to the up locked
    position , the        symbol will appear in
    the display. The power and all other
    buttons will be disabled. This will prevent
    accidental operation when the radio is
    packed in a suitcase. To release the lock
    switch , move the switch to the down
    unlocked position, the        symbol will
    be removed from the display. 
						

							7  Earphones and antenna
The earphones also acts as the FM antenna
when plugged into the earphones jack. While
listening via speaker, you may plug the
supplied wire antenna into the earphones jack,
and set the ST/MO/SP switch to the SP
(speaker) position.
  ST/MO/SP(Stereo/Mono/Speaker)
1. Switch the switch to SP (speaker) position,
    while you listen to the radio program via
    speaker. Make sure to plug the supplied
    wire antenna or the earphones to get best
    FM reception.
2. This radio is capable of receiving FM
    stereo radio program by plug the supplied
    earphones into the earphones jack and set
    the ST/MO/SP switch to ST (stereo)
    position, display will show stereo symbol.
    If the station being received is weak,
    some hiss may be audible, to reduce the
    hiss, switch the ST/MO/SP to MO(mono)
    position. The stereo indicator will be
    removed from the display. 
						

							GB
    8 Change AM (MW) band tuning step
( available only on DT-210/V not for
LW version )
In Europe and other parts of the world, AM
(MW) tuning step are 9 kHz, in America the
AM tuning step is 10 kHz.
To change the AM tuning step from 10 kHz
to 9 kHz, proceed as follows,
1. Press Tuning Down button then the power
    button to switch on the radio, the radio will
    be changed into 9 kHz tuning step on AM
    band.
To change the AM tuning step from 9 kHz to
10 kHz, proceed as follows,
1. Press Tuning UP button then Power button
    to switch on the radio, the radio will be
    changed into 10 kHz tuning step on AM
    band. 
						

							  DBB (Deep Bass Boost) button
Press DBB button to activate the Deep Bass
Boost to have stronger bass sound, display
will appear DBB symbol. Another press will
cancel the DBB.
Note:
Suggest to activate the DBB only using
earphones.
9