Polaroid Polaview 360 Projector User Manual

11Names and functions of each part (continued)Loading the batteriesLoading AA batteries into the remote control.The laser pointer of the remote control is used as a pointer.
N ever look directly into the laser beam outlet or point the laser beam at
other people.
The laser beam can cause vision problems.Warning1R e m ove the battery
cover.
Push the knob while
lifting up the battery
cover.2Loading the batteries.
Make sure the plus and
minus poles are correctly
o r i e n t e d .
3Close the battery...

12InstallationTypical LCD Projector and Screen InstallationUsing the adjustersa.Distance from the LCD projector to the screen
b.Distance from the lens center to the bottom of
the screen (a,b : +/-10%).
The projection distances shown in the diagram to
the left are for full size (1,024 x 768 dots).The LCD projector should normally be used
level (the legs can point upward).
Positioning the projector sideways, or with the
lens pointing upward or downward can cause the
internal temperature to rise, which...

13Basic operationsTo project2
4 572
35
4
7
11Turn on the main power switch of the projector [ I: ON].
• The Power indicator lights orange.2Press the STANDBY / ON button.
• The Power indicator will blink green and then light green.
• The green blinking indicates warmup.3Remove the lens cap.4Use the ZOOM button to adjust the screen size.5Use the FOCUS button to adjust the focus.
(1) The display shown to the right will appear when the FOCUS button is pressed.
(2) Use the FOCUS button to adjust the focus...

14Turning off the powerPlug & PlayBasic operations (continued)1Press the STANDBY/ON button for approximately 1 sec.
• The Power indicator will blink orange, then the lamp will turn off. Approximately 1 sec. after that, the
indicator will light orange.
• After the power is turned off, the lamp will be cooled for approximately 1 min. and the power cannot
be turned off even by pressing the STANDBY/ON button.
• The standby status will not be entered if the time which the STANDBY/ON button is pressed is too...

15Freeze functionBasic operations (continued)1Press the FREEZE button.
• The image being displayed will freeze.
• The [     ] mark appears in the lower right corner of the screen when the Freeze function is on.1Press the FREEZE button.
• The FREEZE function will be cancelled.
• The [     ] mark will be displayed for approximately 3 sec. when the FREEZE function is cancelled.1This function is used to freeze the image being displayed.
(refer to page 10)Cancelling the FREEZE function•When there is no input...

161Press the MAGNIFY+
button.
• The center part of the image will be displayed magnified approximately 2x.2Press the MAGNIFY +
bu t t o n .
• When this button is pressed, the image will be displayed even larger.3Press the MAGNIFY 
–button.
• When this button is pressed, the image will be displayed even smaller.4Press the POSITION button.5Press the DISK PAD up, down, left and right buttons.
• The magnified area will move in accordance with the button pressed.6Press the MAGNIFY OFF button.Magnify...

17Returning to the initial settingsAdjustments and functions1Press the MENU (             ) buttons of the projector or the
MENU button of the remote control.
• The Menu screen will appear. (refer to page 18 - 21 for details.)2Press the MENU (                 ) buttons of the projector or the DISK
PAD button of the remote control to select the menu item to be
a d j u s t e d .
• The selected menu item will be displayed in orange.3Adjust the selected menu item with the MENU (             )
buttons of the...

18Adjustments and functions (continu e d )
RGB signal inputVideo signal input•The menu cannot be displayed while the initial screen (“No input is detected.” or “Sync is
out of range.”) is being displayed.
• Tint cannot be adjusted with N-PAL, M-PAL, PAL or SECAM video signal input.
• Tint, color and sharpness cannot be adjusted with RGB signal input.
• V. POSIT, H. POSIT, H. PHASE and H. SIZE cannot be adjusted with video signal input.
• FREEZE function will be cancelled after the operation “Menu”.
•...

19Adjustments and functions (continu e d )INPUTThe INPUT menu is used to select RGB signal sync signal frequency of the monitor and the VIDEO signal.Adjustment item
RGB
VIDEOAdjustment description
Displays the following RGB inputs
fH: horizontal sync frequency
fV: vertical sync frequency
Sets the video signal system. When the screen is unstable (no color) 
or rolls, select the mode that matches the input signal. 

20Adjustments and functions (continu e d )Adjustment item
KEYSTONE
MIRROR
BLANK
START UP
P in PAdjustment description
Reduces keystoneReduces keystone
distortion at the bottomdistortion at the top
Sets vertical or horizontal inversion of the projected image.
H: horizontal inversion only
V: vertical inversion only
H&V: both horizontal and vertical inversion.
Sets the color to be used for blanking with BLANK ON or when there is no signal. 
Blanking is turned on, when there is no signal for approximately 5...