ProForm 460 R Manual

Model No. 831.21833.2
Serial No.                                  
Write the serial number in the 
space above for reference.
Serial Number Decal 
(under frame)
    CAUTION
Read all precautions and instruc-
tions in this manual before using 
this equipment. Keep this manual 
for future reference.
BIKE EXERCISER
User’s Manual
• Assembly
• Operation
• Maintenance
• Part List and Drawing
Sears, Roebuck and Co.
Hoffman Estates, IL 60179 

2
WA R N I N G   D E C A L  P L A C E M E N T
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

3
IMPORTANT PRECAUTIONS
    WARNING: To reduce the risk of serious injury, read all important precautions and 
instructions in this manual and all warnings on your exercise bike before using your exercise bike. 
Sears assumes no responsibility for personal injury or property damage sustained by or through the 
use of this product.
1.  It is the responsibility of the owner to ensure 
that all users of the exercise bike are ade-
quately informed of all precautions. 
2.  Before beginning any exercise...

4
Seat
Backrest
Seat Handle
Pedal/Strap
Wheel
Console
Water Bottle Holder*
Handlebar
Heart Rate Monitor
Leveling Foot*Water bottle is not included
BEFORE YOU BEGIN
Thank you for selecting the new PROFORM® 460 
R exercise bike. Cycling is an effective exercise for 
increasing cardiovascular fitness, building endurance, 
and toning the body. The 460 R exercise bike provides 
an impressive selection of features designed to make 
your workouts at home more effective and enjoyable.
For your benefit, read this...

5
M8 x 16mm Screw (60)–4
M10 x 68mm Screw (44)–4
M8 x 38mm Screw (61)–4
M6 x 40mm Screw (51)–10M4 x 12mmScrew (57)–2
M4 x 15mm Self-tappingScrew (63)–4
M8 x 18mmScrew (42)–2
 PART IDENTIFICATION CHART
Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each 
drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the 
key number is the quantity needed for assembly. Note: If a part is not in the...

6
ASSEMBLY
•  Assembly requires two persons.
•  Place all parts in a cleared area and remove the 
packing materials. Do not dispose of the packing 
materials until you fi nish all assembly steps.
•  Left parts are marked “L” or “Left” and right parts 
are marked “R” or “Right.”
•  To identify small parts, see page 5.
In addition to the included tool(s), assembly 
requires the following tools:
one Phillips screwdriver 
one adjustable wrench 
Assembly may be easier if you have a set of 
wrenches. To avoid...

7
3
244
1
3.  Set a sturdy piece of packing material under the 
Frame (1).
 Orient the Front Stabilizer (2) as indicated by the 
sticker. Attach the Front Stabilizer to the Frame 
(1) with two M10 x 68mm Screws (44). 
 Remove the packing material.
44.  Orient the Upright (4) as shown.
 Tip: Avoid pinching the Main Wire (41). Attach 
the Upright (4) to the Frame (1) with four M8 x 
16mm Screws (60); start all the Screws, and 
then tighten them.
 Next, locate the wire tie in the Upright (4). Tie the 
lower...

8
5
66.  Attach the Seat Frame (14) to the Seat Carriage 
(11) with two M6 x 40mm Screws (51).
14
51
11
 5.  Orient the Rear and Front Upright Covers (19, 
20) as shown.
 Press the Rear and Front Upright Covers (19, 
20) together around the Upright (4), and join 
them with two M4 x 12mm Screws (57).
 Then, press the Rear and Front Upright Covers 
(19, 20) downward onto the Left and Right 
Shields (21, 22).
19
20
21, 2257
57
4 

9
7
18
61
8
7.  Attach the Seat (12) to the Seat Carriage (11) 
and the Seat Frame (14) with four M6 x 40mm 
Screws (51).
12
11
8.  Orient the Seat Handlebar (18) as indicated by 
the sticker.
 Attach the Seat Handlebar (18) to the Seat 
Frame (14) with four M8 x 38mm Screws (61).
14
51
14 

10
10
99.  Attach the Backrest (13) to the Seat Frame (14) 
with four M6 x 40mm Screws (51).
14
13
51
51
10. Orient the Handlebar (6) as shown. 
 Tip: Avoid pinching the Pulse Wire (58). 
Attach the Handlebar (6) to the Upright (4) with 
two M8 x 18mm Screws (42). 58
42
64
Avoid pinching the 
Pulse Wire (58)