ProForm 60 Ce Elliptical Manual

Serial Number 
Decal (under frame)
    CAUTION
Read all precautions and instruc-
tions in this manual before using 
this equipment. Keep this manual 
for future reference.
Model No. PFEL53911.1
Serial No.                                  
Write the serial number in the space 
above for reference.
QUESTIONS?
If you have questions, or if parts 
are damaged or missing, DO NOT 
CONTACT THE STORE; please 
contact Customer Care.
IMPORTANT: Please register this 
product (see the limited warranty 
on the back...

2
WARNING DECAL PLACEMENT
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

3
    WARNING: To reduce the risk of serious injury, read all important precautions and 
instructions in this manual and all warnings on your elliptical before using your elliptical. ICON 
assumes no responsibility for personal injury or property damage sustained by or through the use of 
this product.
1.  Before beginning any exercise program, 
consult your physician. This is especially 
important for persons over age 35 or per-
sons with pre-existing health problems.
2.  Use the elliptical only as...

4
BEFORE YOU BEGIN
Thank you for selecting the revolutionary PROFORM® 
6.0 CE elliptical. The 6.0 CE elliptical provides an 
impressive selection of features designed to make your 
workouts at home more effective and enjoyable.
For your benefit, read this manual carefully before 
you use the elliptical. If you have questions after 
reading this manual, please see the front cover of this 
manual. To help us assist you, note the product model 
number and serial number before contacting us. The 
model...

5
Bolt Set (31),2M8 x 45mm Button Bolt (76),4
M10 x 45mm Screw (75),6M10 x 85mm Screw (82),4
M10 SplitWasher (78),11M8 Jam Nut (77),4M8 Washer 
(33),2
M10 x 20mmScrew (79),8M8 x 20mm Screw (80),2
M4 x 16mm Screw (92),9
 PART IDENTIFICATION CHART
Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each 
drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the 
key number is the quantity needed for...

6
1.  While a second person lifts the rear of the Frame 
(1), attach the Rear Stabilizer (70) to the Frame 
with two M10 x 85mm Screws (82).
1
70
1
1
82
82
2.  Orient the Front Stabilizer (73) as indicated by 
the sticker.
  While a second person lifts the front of the 
Frame (1), attach the Front Stabilizer (73) to the 
Frame with two M10 x 85mm Screws (82).
2
73
a  To hire an authorized service technician to 
assemble the elliptical, call 1-800-445-2480.
a  Assembly requires two persons.
a  Place all...

7
33.  Orient the Upright (2) and the Shield Cover (37) 
as shown. Slide the Shield Cover upward onto 
the Upright.
  Have a second person hold the Upright (2) and 
the Shield Cover (37) near the Frame (1).
  Locate the wire tie in the lower end of the Upright 
(2). Tie the wire tie to the Main Wire (42). Then, 
pull the upper end of the wire tie until the Main 
Wire is routed through the Upright.
  Tip: To prevent the Main Wire (42) from fall-
ing into the Upright (2), secure the Main Wire 
with the...

8
4
5
4. Tip: Avoid pinching the Main Wire (42). Slide 
the Upright (2) onto the Frame (1). 
  Have a second person hold the Shield Cover 
(37) out of the way.
  Attach the Upright (2) with five M10 x 20mm 
Screws (79) and five M10 Split Washers (78). 
Tip: Start all the Screws before fully tighten-
ing them.
  Press the Shield Cover (37) into the Left and 
Right Shields (44, 45).2
2
1
37
797878
39
93
79
79
79
Avoid pinching the 
Main Wire (42)
Avoid pinching 
the wires
5.  Orient the Handlebar (39) as...

9
77.  Untie and discard the wire tie on the Main Wire 
(42).
  While a second person holds the Console (4) 
near the Upright (2), connect the wires on the 
Console to the Main Wire (42) and to the Sensor 
Wires (93). 
  Insert the excess wire into the Upright (2) or into 
the Console (4). 
 Tip: Avoid pinching the wires. Attach the 
Console (4) to the Upright (2) with four M4 x 
16mm Screws (92).
4
42
92
2
93
4
Battery 
Cover
Battery 
Cover
6 6.  The Console (4) can use four D batteries (not 
included);...

10
1010. Identify the Right Upper Body Arm (9), which is 
marked with an dRe sticker. 
  Orient the Right Upper Body Arm (9) and an 
Upper Body Leg (6) as shown. Insert the Right 
Upper Body Arm into the Upper Body Leg. 
  Attach the Right Upper Body Arm (9) to the 
Upper Body Leg (6) with two M8 x 45mm Button 
Bolts (76) and two M8 Jam Nuts (77). Make sure 
that the Jam Nuts are inside the hexagonal 
holes. Do not fully tighten the Byon Bolts 
yet.
 Assemble the Left Upper Body Arm (8) and 
the other...