ProForm 60 Instruction Manual

USER’S MANUAL
    CAUTION
Read all precautions and instruc-
tions in this manual before using 
this equipment. Keep this manual 
for future reference.
Model No. PFTL39511.0
Serial No.                                  
Write the serial number in the space 
above for reference.
QUESTIONS?
If you have questions, or if parts 
are damaged or missing, DO NOT 
CONTACT THE STORE; please 
contact Customer Care.
IMPORTANT: Please register this 
product (see the limited warranty 
on the back cover of this manual)...

2
PROFORM is a registered trademark of ICON IP, Inc.
WARNING DECAL PLACEMENT
This drawing shows the locations of the 
warning decals. If a decal is missing 
or illegible, call the telephone num-
ber on the front cover of this manual 
and request a free replacement 
decal. Apply the decal in the location 
shown. Note: The decals may not be 
shown at actual size.
256836
TABLE OF CONTENTS
WARNING DECAL PLACEMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . . . . . . . . . ....

3
IMPORTANT PRECAUTIONS
1.   Before beginning any exercise program, con-
sult your physician. This is especially impor-
tant for persons over age 35 or persons with 
pre-existing health problems.  
2.   It is the responsibility of the owner to ensure 
that all users of this treadmill are adequately 
informed of all warnings and precautions.
3. Use the treadmill only as described.
4.   Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a 
garage or covered patio, or...

4
20.  Never leave the treadmill unattended while 
it is running. Always remove the key, unplug 
the power cord, and press the power switch 
into the off position when the treadmill is not 
in use. (See the drawing on page 5 for the 
location of the power switch.)  
21.  Do not attempt to raise, lower, or move the 
treadmill until it is properly assembled. (See 
ASSEMBLY on page 7, and HOW TO FOLD 
AND MOVE THE TREADMILL on page 19.) 
You must be able to safely lift 45 lbs. (20 kg) 
to raise, lower, or...

5
Thank you for selecting the new PROFORM® 6.0 RT 
treadmill. The 6.0 RT treadmill provides an impressive 
selection of features designed to make your workouts 
at home more effective and enjoyable.
For your benefit, read this manual carefully before 
you use the treadmill. If you have questions after 
reading this manual, please see the front cover of this 
manual. To help us assist you, note the product model 
number and serial number before contacting us. The 
model number and the location of the...

6
PART IDENTIFICATION CHART
Use the drawings below to identify small parts used for assembly. The number in parentheses below each draw-
ing is the key number of the part, from the PART LIST near the end of this manual. The number following the key 
number is the quantity used for assembly. Note: If a part is not in the hardware kit, check to see if it is preat-
tached. Extra hardware may be included.
#10 x 3/4 Screw(8)–6 #8 x 3/4 Screw
(4)–10
#10 x 1/2
Screw (8)– 2 #8 x 1/2 Ground
Screw (1)–1
3/8 x 3...

7
1. Make sure that the power cord is unplugged.
 Remove and discard the two screws (A) and the 
shipping bracket (B) from the right side of the 
Base (74). 
 Then, remove and discard the screws and the 
shipping bracket (not shown) from the left side of 
the Base.
•	To hire a service technician to assemble this prod-
uct in your home, call 1-800-445-2480. 
•	Assembly requires two persons.
•	Place all parts in a cleared area and remove the 
packing materials. Do not dispose of the packing 
materials...

8
3. Identify the Right Upright (76), which is marked 
“Right.” Have a second person hold the Right 
Upright near the Base (74).
 See the inset drawing. Tie the wire tie in the 
Right Upright (76) securely around the end of 
the Upright Wire (63). Then, insert the Upright 
Wire into the lower end of the Right Upright as 
you pull the other end of the wire tie through the 
Right Upright. 
74
76
63
76
Wire Tie
Wire 
Tie
3
63
4.  Hold the Right Upright (76) against the Base 
(74). Be careful not to pinch...

9
Bolts and washers
pr eattached in Logen\
5.    Identify the Right Handrail (64), which is marked 
“Right.” Have a second person hold the Right 
Handrail near the Right Upright (76).
    Route the Upright Wire (63) into the bottom of 
the Right Handrail (64) and out of the hole in the 
Right Handrail.
  Be careful not to pinch the Upright Wire (63). 
Insert and partially tighten a 5/16" x 3/4" Screw 
(5) with a 5/16" Star Washer (6) into the Right 
Upright (76) and the Right Handrail (64)....

10
8
61
7
7
5
5
8
8
23
76
66
8.    Attach the Console Crossbar (61) to the Left 
and Right Uprights (66, 76) with four #10 x 3/4" 
Screws (8) and four #10 Star Washers (23). 
Start all four Screws, and then tighten them.
  Firmly tighten the two 5/16" x 3/4" Screws (5) 
and two 5/16" x 3" Screws (7).
7.    Remove the four screws (D) from the Left and 
Right Handrails (59, 64). Discard the screws.7
D
D
64
59
23