ProForm Hybrid Trainer Pfel038152 Manual

    CAUTION
Read all precautions and 
instructions in this manual before 
using this equipment. Keep this 
manual for future reference.
Model No. PFEL03815.2
Serial No.                                  
Write the serial number in the space 
above for reference.
USER’S MANUAL
www.proform.com
Serial 
Number 
Decal
To register your product and 
activate your warranty today, 
go to www.proformservice.com/
registration.
For service at any time, go to 
www.proformservice.com.
Or call 1-888-533-1333
Mon.–Fri. 6...

2
WARNING DECAL PLACEMENT
TABLE OF CONTENTS
WARNING DECAL PLACEMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS ..................................................................3
BEFORE YOU BEGIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
PART IDENTIFICATION CHART. . . . . . . . . . . . . . . . . ....

3
    WARNING: To reduce the risk of serious injury, read all important precautions and 
instructions in this manual and all warnings on your hybrid trainer befo\
re using your hybrid trainer. 
ICON assumes no responsibility for personal injury or property damage su\
stained by or through the 
use of this product.
1. It is the responsibility of the owner to ensure 
that all users of the hybrid trainer are ade-
quately informed of all precautions.
2. Before beginning any exercise program, 
consult your...

4
 
 
 
 
 
 
 
 
  all 
 
 
S TAND ARD SERVICE PLANS   

5
BEFORE YOU BEGIN
Thank you for selecting the revolutionary PROFORM® 
HYBRID TRAINER. The HYBRID TRAINER provides 
an impressive selection of features designed to make 
your workouts at home more effective and enjoyable.
For your benefit, read this manual carefully before 
you use the hybrid trainer. If you have questions after 
reading this manual, please see the front cover of this 
manual. To help us assist you, note the product model 
number and serial number before contacting us. The 
model number...

6
M10 x 80mm Screw (19)–4M10 x 20mm 
Screw (76)–6
M8 Locknut  (68)–10M8 Washer  (87)–6
M8 x 38mm Bolt (95)–4M8 x 12mm 
Screw (106)–6M8 x 14mm Shoulder
Screw (86)–6M8 x 38mm Hex  Bolt (102)–6
M4 x 16mm 
Screw (115)–6M6 x 35mm Screw  (98)–4M6 x 20mm 
Screw (97)–4
PART IDENTIFICATION CHART
Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each 
drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the...

7
• To hire an authorized service technician to 
assemble the hybrid trainer, call 1-800-445-2480.
• Assembly requires two persons.
• Place all parts in a cleared area and remove the 
packing materials. Do not dispose of the packing 
materials until you finish assembly.
• Left parts are marked “L” or “Left” and right parts 
are marked “R” or “Right.”
• To identify small parts, see page 6.
• In addition to the included tool(s), assembly 
requires the following tools:
one Phillips screwdriver 
one...

8
44. Set the Upright (2) near the Frame (1) as shown.
 Locate the wire tie in the Frame (1) and pull 
the Main Wire (96) out of the underside of the 
Frame. 
 Repeat this action to pull the Upper Wire 
(not shown) out of the underside of the 
Upright (2).
 Then, untie and discard the wire ties.
96
33. Orient the Upright (2) and the Front Stabilizer (5) 
so that the large holes are facing the Upright. 
 Attach the Front Stabilizer (5) to the Upright (2) 
with two M10 x 80mm Screws (19).
19
52
2
1
Large...

9
5
76
7696
94
76
5. Tip: Avoid pinching the wires. Insert the 
Upright (2) into the Frame (1). 
 Attach the Upright (2) with six M10 x 20mm 
Screw (76); start all the Screws, and then 
tighten them.
 Then, connect the Upper Wire (94) to the Main 
Wire (96).
Avoid pinching 
the wires
Avoid pinching 
the wires
66. Locate the wire tie in the top of the Upright (2) 
and pull the Upper Wire (94) out of the Upright. 
Then, untie and discard the wire tie.
 Tip: Avoid pinching the wires. Attach the Wire 
Cover...

10
94
3
2
2
3
Grease
Avoid 
pinching 
the Upper 
Wire (94)
8
13
9480
8. Using a plastic bag to keep your fingers clean, 
apply a generous amount of the included grease 
to the Pivot Axle (80).
 Tip: Avoid pinching the Upper Wire (94). Slide 
the Pivot Bracket (3) onto the Upright (2) and 
hold it in place.
 Next, insert the Pivot Axle (80) into the Pivot 
Bracket (3) and into the Upright (2). Center the 
Pivot Axle.
 Then, tighten the Pivot Knob (13) into the Pivot 
Bracket (3).
77. Have a second person...