Radocy Russian M44 Carbine Instructions Manual

Russian M44 Carb
Takedown Guide
MADE EASY
Clean your own gun with confidence.
Saves you money on repairs! 

Russian }d44 Carbine
CA
I Bolt Head/Extsactor2 Bolt Comector/Gilide Bar3 Firing Pin4 Firing Fin Spring5 Bolt6 Cmking Pice7 Bolt Assonbly8 Tmg Screw9 Ejoctor Spring Screwl0 Ejecmr Spring/Feed lnt€rruptqll Ej€ctorl2 Reeivqll Barr€l14 Rear Sight15 Front Sigbt| 6 Triggerl7 Trigger Hinge Pinl8 Trigg€r Spring/Bolt StoP19 Bolt Siop Screw20 Triggd Guard/Magazin€2l FrontGuard Screw22 Megazine Spring/Floorpla0e Assembly23 Floorplare t atch24 Flmrplate Lrtch Screw
Copyright @2003 By Radocy Products, Co.
WARNING:...

l. Open the bolt. To remove the
bolt hold the trigger back and pull
the bolt out.
2. Hold the front of the bolt and pull back
the cocking knob and turn it counter
clockwise; putting the striker in the.fired
posltlon.
Shown how the bolt should look.
3. Shde the bolt
connector and bolt
head off from the
front. 

4. Turn the bolt head counter-
clockwise until it stops and remove it.
5. The extractor
should not be removed. It is dovetail mounted in the bolt head. If it is
broken have a gunsmith replace.
6. The striker is screwed into the cocking knob at the rear of the bolt. Use the forked end
of the bolt connector guide as a wrench
to unscrew the striker. It may be tight,
do not use force or the bolt connector
guide could be broken. It is under
tension. As you start to release it keep
it under control.
7. Remove...

11. After the screw and spring are
removed, drift out the cross pin show to
remove the arm from the floorplate.
9. Squeeze the magazine follower to
open the end and remove it back and
out.
-
12. Driftthis pin out to separate the follower
spring and arm.
Shown outside
L0. the magazine mainspring is retained
inside the floorplate bv a screw.
M44 

L3. Pull the rod out.
14. Unscrew this
large screw to
remove the
bayonet.
15. tf the rifle has a full stock with the upper handguard, push the spring catches and
slide the barrel bands forward. The barrel bands will not fit over the bayonet mount.
Removal is not recommended(of the sight and bayonet mount). The bands can be
stretched stightly. It is recommended that you leave them on, unless for repairs.
16. Remove the upper handguard. 

18. Then the large screw on the bottom
of the masazine housins.
17. To remove the stock, unscrew
the large at the top rear of the gun.
L9. The small screw at the front will
release the stock cap. This does not need
to be removed, unless for repairs.
20. Separate
the stock from
the trigger guardlmagazine and
the barreled assemblv. 

floorplate latch is its own spring.
Unscrew the screw and remove
the latch down.
21.The magazine
I
22. The ejector and feed intemrpter are on the left side of the barreled assembly. It may
be a two-piece or one-piece depending on the model. Unscrew the screw at the rear and
drift it forward out of its dovetail. *Note how the two pieces fit together before
disassembly. 

23. Unscrew the large screw
underneath the barreled assembly.
The trigger spring/bolt stop will
not be removed at this time.
24, Drtft out the trigger pin and remove the trigger
spring/bolt stop and trigger.