Ricoh Aficio MP161L User Manual

							x Clearing Misfeeds
35
4 x Clearing Misfeeds
R CAUTION:
Important
❒When clearing misfeeds, do not turn off the power switch. If you do, your
copy settings are cleared.
❒To prevent misfeeds, do not leave any torn scraps of paper inside the ma-
chine.
❒If paper misfeeds occur repeatedly, contact your service representative.
Note
❒More than one misfeed area may be indicated. If this is the case, check every
applicable area. Refer to the following charts: A, P, Y.
❒You can find a sticker explaining how to remove misfed paper inside the right
cover.
❒When the machine instructs you to reset originals, reset them in the feeding
position. The display will show you the number of originals to return. The fusing section of this machine might be very hot. Caution should be tak-
en when removing misfed paper.
ARK028S
Downloaded From ManualsPrinter.com Manuals 
						

							Troubleshooting
36
4
ARK029S
12
12
12
123
456
Downloaded From ManualsPrinter.com Manuals 
						

							Changing the Paper Size
37
4 Changing the Paper Size
Preparation
Be sure to select the paper size
with User Tools and the paper size
selector. If you do not, misfeeds
might occur. See p.24 “Paper Size:
Tray 1–2”.
Reference
For details about paper sizes and
types, see p.48 “Copy Paper”.
Changing the Paper Size of the 
Paper Tray (Tray 1)
AMake sure the paper tray is not in
use.
BPull the paper tray out slowly un-
til it stops.
Note
❒Remove any remaining copy
paper.
CWhile pressing the release lever,
pull the back fence off from the
tray.
When using A4L size paper
APlace the back fence in the cor-
ner pocket on the left.
DWhile pressing the release lever,
adjust the side fences.
EPush the metal plate down.
ARK011S
ARK012S
ARK013S
ARK014S
Downloaded From ManualsPrinter.com Manuals 
						

							Troubleshooting
38
4
FSquare the paper and load it in
the tray.
Important
❒Be sure to set the paper under
the roller.
❒Do not stack paper over the lim-
it mark.
GWhile pressing the release lever,
adjust the side fences to the new
paper size.
Important
❒When setting small quantities of
copy paper, be careful not to
squeeze in the side fence too
much or paper will not feed in
properly.
HWhile pressing the release lever,
set the back fence to the new size.
IPush the paper tray in until it
stops.
Changing the Paper Size in the 
Paper Tray Unit (Tray 2)
AMake sure the paper tray is not in
use.
BPull out the paper tray until it
stops.
Note
❒Remove any remaining copy
paper.
CWhile pinching the release lever,
adjust the back fence.
ARK015S
ARK016S
ARK017S
Downloaded From ManualsPrinter.com Manuals 
						

							Changing the Paper Size
39
4
When loading 81/4 × 14L or 
81/2 × 14L size paper
APull the back fence off from
the tray.
B Place it in the corner pocket on
the left.
DWhile pressing the release lever,
adjust the side fences.
EPush the metal plate down, and
then square the paper and load it
in the tray.
Important
❒Do not stack paper over the lim-
it mark.
❒Load paper so that the paper
touches the right side of the
tray, or misfeeds might occur.
FWhile pinching the release lever,
adjust the side and back fences to
the new paper size.
Important
❒When loading small quantities
of copy paper, be careful not to
squeeze in the side fence too
much or paper will not feed in
properly.
GPush the paper tray in until it
stops.
Downloaded From ManualsPrinter.com Manuals 
						

							Troubleshooting
40
4
Selecting the Paper Size with 
User Tools
APress the {User Tools/Counter} key.
BSelect [System Settings] using {U}
or {T}, and then press the {OK}
key.
CSelect [Tray Paper Settings] using
{U} or {T}, and then press the
{OK} key.
DSelect the paper tray you want to
change the paper size for using
{U} or {T}, and then press the
{OK} key.
ESelect the paper size using the
scroll keys, and then press the
{OK} key.
The “
Programmed” message ap-
pears.
FPress the {User Tools/Counter} key.
ARK004S
Downloaded From ManualsPrinter.com Manuals 
						

							41
5. Other Functions
Other Functions
Displaying the Total Counter
You can display the total counter val-
ue used for all functions.
APress the {User Tools/Counter} key.
BSelect [Counter] using {U} or {T},
and then press the {OK} key.
CTo print the counter list, press
[Print].
Note
❒To print the counter list, load
A4L or 81/2 × 11 L size pa-
per.
DPress the {Start} key.
A counter list prints out.
EPress the {User Tools/Counter} key.
Changing the Language
You can change the language used on
the display. English is set as default.
APress the {User Tools/Counter} key.
BSelect [Language] using {U} or
{T}, and then press the {OK} key.
CSelect the language using {U} or
{T}, and then press the {OK} key.
The “ 
Programmed ” message ap-
pears, and then the “ User Tools ”
display returns.
DPress the {User Tools/Counter} key.
ARK004S
ARK004S
Downloaded From ManualsPrinter.com Manuals 
						

							Other Functions
42
5
Downloaded From ManualsPrinter.com Manuals 
						

							43
6. Specifications
Main Unit
❖Configuration:
Desktop
❖Photosensitivity type:
OPC drum
❖Original scanning:
One-dimensional solid scanning system through CCD
❖Copy process:
Dry electrostatic transfer system
❖Development:
Dry two-component magnetic brush development system
❖Fusing:
Heating roll pressure system
❖Resolution:
600 dpi
❖Exposure glass:
Stationary original exposure type
❖Original reference position:
Rear left corner
❖Warm-up time:
From the main power switch
10 seconds or less (20 °C)
From the operation switch
10 seconds or less (20 °C)
❖Originals:
Sheet/book/objects
❖Maximum original size:
A4L, 81/2 × 14L
Downloaded From ManualsPrinter.com Manuals 
						

							Specifications
44
6
❖Copy paper size:
Trays: A4L, B5 JISL, A5K, 81/2 × 11L, 51/2 × 81/2K, 16KL
Bypass: 
A4L, A5KL, B5 JISL, 81/2 × 14L, 81/2 × 11L, 51/2 × 81/2KL,
71/4 × 101/2L, 8 × 13L, 81/2 × 13L, 81/4 × 13L, 81/4 × 14L,
16KL, 41/8 × 91/2L, 37/8 × 71/2L, C5 EnvL, C6 EnvL, DL EnvL
 Bypass (custom size):
Vertical: 90 – 216 mm, 3.5 – 8.5
Horizontal: 140 – 600 mm, 5.6 – 23.7
 Duplex unit: A4 L, B5 JIS L, 8
1/2 × 14 L, 81/2 × 11 L, 81/2 × 13 L,
81/4 × 14L, 81/4 × 13 L, 16K L
❖Copy paper weight:
 Paper trays (Standard size): 60 – 90 g/m2, 16 – 24 lb
 Bypass tray: 60 – 157 g/m
2, 16 – 42 lb
 Duplex unit: 64 – 90 g/m
2, 20 – 24 lb
❖Non-reproduction area:
 Leading edge: 2 ± 1.5 mm (0.08 ± 0.06 inch)
 Trailing edge: more than 0.5 mm (0.02 inch)
 Left edge: 2 ± 1.5 mm (0.08 ± 0.06 inch)
 Right edge: more than 0.5 mm (0.02 inch)
❖First copy time:
7.5 seconds or less
(A4L, 81/2 × 11L 100%, feeding from Tray 1)
❖Copying speed: (Type 1)
 16 copies/minute (A4L, 81/2 × 11L)
❖Reproduction ratio:
Preset reproduction ratios:
Zoom: From 50% to 200% in 1% steps.
❖Continuous copying count:
1 – 99 copies
— Metric version Inch version
Enlargement 200% 155%
141% 129%
Full Size 100% 100%
Reduction 93% 93%
71% 78%
50% 65%
Downloaded From ManualsPrinter.com Manuals