Ricoh Projector PJ WX6181N User Manual

26
❻ Optimizing Computer Signal Automatically
Adjusting the Image Using Auto Adjust
When projecting a signal from the computer video input terminal, BNC video input terminal (anlaog RGB), HDMI 1 input terminal, 
HDMI 2 input terminal, DisplayPort input terminal, adjust the picture quality with a single touch of the button if the edges of the 
screen are cut off or if the projection quality is bad.
Press the AUTO ADJ. button to optimize a computer image automatically.
This adjustment may be necessary when...

27
❽ Turning off the Projector
To turn off the projector:
Eternet
1. First, press the  (POWER) button on the projector cabinet 
or the STANDBY button on the remote control. 
  The [POWER OFF / ARE YOU SURE ? / CARBON SAVINGS- SES-
SION 0.000[g-CO2]] message will appear.
2. Secondly, press the ENTER button or press the  (POWER) 
or the STANDBY button again.
  The lamp will go off and the power supply will be cut. At this 
point, if there are no input signals, the projector will go into the 
standby mode...

28
❾ After Use
Preparation: Make sure that the projector is turned off.
1. Unplug the power cord.
2.  Disconnect any other cables.
3.  Mount the lens cap on the lens.
4.  Before moving the projector, screw in the tilt feet if they have been lengthened.
2. Projecting an Image (Basic Operation)  

29
❶ Turning off the Image and Sound
The projected video and the output sound from the internal speaker and sound 
output terminal will disappear momentarily.
Press the BLANK button.
The projected video will be cut off.
Press the MUTE button.
The projected audio will be cut off.
Press the AV-MUTE button.
The projected video and audio will be cut off.
• Press the buttons one more time for the cancelled video and audio to appear 
again.
  When AV-MUTE and BLANK are continued for some time, the...

30
❷ Freezing a Picture
Press the FREEZE button to freeze a picture. Press again to resume motion.
NOTE: The image is frozen but the original video is still playing back.
❸ Enlarging a Picture
You can enlarge the picture up to four times.
NOTE: 
•  Depending on an input signal, the maximum magnification may be less than four times, or the function 
may be restricted.
To do so:
1.  Press the D-ZOOM (+) button to magnify the picture.
2. Press the ▲▼◀▶ button.
  The area of the magnified image will be...

31
❹ Changing Eco Mode/Checking Energy-Saving Effect Using Eco Mode 
[ECO MODE]
This feature enables you to select two brightness modes of the lamp:
OFF and ON modes. The lamp life can be extended by turning on the [ECO MODE].
[ECO MODE] Description
[OFF] This is the default setting (100% Brightness).
[ON]
Low lamp power consumption (approx. 80% Brightness).
To turn on the [ECO MODE], do the following: 
1.  Press the ECO button on the remote control to display [ECO MODE] screen.
2.  Use the ▲ or ▼ button...

32
Checking Energy-Saving Effect [CARBON METER]
This feature will show energy-saving effect in terms of CO2 emission reduction (kg) when the projector’s [ECO MODE] is set to 
[OFF], or [ON]. This feature is called as [CARBON METER].
There are two messages: [TOTAL CARBON SAVINGS] and [CARBON SAVINGS-SESSION]. The [TOTAL CARBON SAVINGS] message 
shows the total amount of CO
2 emission reduction from the time of shipment up to now. You can check the information on [USAGE 
TIME] from [INFO.] of the menu. (→...

33
❺ Correcting Horizontal and Vertical Keystone Distortion 
[CORNERSTONE]
Use the [CORNERSTONE] feature to correct keystone (trapezoidal) distortion to make the top or bottom and the left or right side 
of the screen longer or shorter so that the projected image is rectangular.
1. Press and hold the Geometric. button for a minimum of 2 seconds to reset current adjustments.
  Current adjustments for [GEOMETRIC CORRECTION] will be cleared.
2.  Project an image so that the screen is smaller than the area...

34
5. Press the ▼ button to align with the [CORNERSTONE] and then press the ENTER button.
The drawing shows the upper left icon ( ) is selected.
 The screen will switch to the [CORNERSTONE] screen.
NOTE:
• When a [GEOMETRIC CORRECTION] function other than [CORNERSTONE] has been set up, the [CORNERSTONE] screen will not be displayed. When the screen is not 
displayed, either press the Geometric. button for 2 or more seconds, or run [RESET] in[GEOMETRIC CORRECTION] to clear the adjustment value of...

35
11. Press the ◀ or ▶ button to highlight the [OK] and press the ENTER button.
  This completes the [CORNERSTONE] correction.
• Select [CANCEL] and press the ENTER button to return to the [CORNERSTONE] screen.
Selecting [CANCEL] will return to the adjustment screen without saving changes (Step 3).
Selecting [RESET] will return to the factory default.
Selecting [UNDO] will exit without saving changes.
NOTE: 
•  Even when the projector is turned on, the last used correction values are applied.
•  Carry...