Roland VersaUV LEC 330 User Manual

49Chapter 3 Operation of the Media Take-up System
3-2 Using the Media Take-up System
Loading Roll Media
1.Pass the media through the printer. 
Move the dancer roller toward the rear. 
Load the roll media.
 P.31, "Loading Media"
Pull back the loading lever.
The media is secured in place. 
2.Fasten the media to the paper tube.
When you attach the paper tube, insert it securely onto the end caps on the take-up unit. For information on how to install 
it, refer to the Setup Guide. 
Useto select...

3-2 Using the Media Take-up System
50Chapter 3 Operation of the Media Take-up System
Pressto adjust the length of the media to be pulled out.
You can adjust the length of the media in 10-millimeter steps by pressing. 
(To pull out media continuously, hold down
. )
Fasten the media in place with tape at three locations (the center and both edges) so that 
the media is not at an angle. 
Take-up with outward curl 
Take-up with inward curl 
Fasten first. 
Paper tube Adhesive tape (3 places)
Fasten first....

3-2 Using the Media Take-up System
51Chapter 3 Operation of the Media Take-up System
3.Make the setting for the direction of automatic take-up and perform take-up 
of the media onto the paper tube. 
Press.
The media is pulled out and the screen shown in the figure appears. 
Pull the dancer roller back toward you.
Make sure the media is stretched taut, and press .
The screen shown in the figure appears.
Make the setting for the AUTO switch on the take-up unit. 
Take-up with outward curl 
Take-up with...

3-2 Using the Media Take-up System
52Chapter 3 Operation of the Media Take-up System
Press.
Making the setting is complete when the screen shown in the figure (the top menu) 
appears.
To Take up Media Manually
You can take up media by using the MANUAL switch. However, never operate the MANUAL switch while the loading lever is 
pulled back. Doing so may cause the media to be pulled with excessive force, actuating the protective feature and resulting 
in an error.
Removing Taken-up Media 
 CAUTION Removal...

53
Chapter 4  
Maintenance and  
Adjustment
Downloaded From ManualsPrinter.com Manuals 

54Chapter 4 Maintenance and Adjustment
4-1 Daily Care and Maintenance
Disposing of Discharged Ink
The drain bottle collects discharged fluid. Dispose of collected material before the bottle becomes full. The message shown 
in the figure appears when a certain amount of discharged fluid has collected in the bottle. Follow the procedure below to 
discard the discharged fluid.Resetting the discharged-fluid counter after disposal makes the message shown in 
the figure disappear. 
Press .
1.Choose the...

4-1 Dairy Care and Maintenance
55Chapter 4 Maintenance and Adjustment
3.Attach the emptied bottle and reset the discharged-fluid count.
Attach the emptied bottle.
Press.
Pressa second time.
Press.
Press
to go back to the original screen.
 WARNING  Never place discharged fluid near open flame. 
Doing so may cause fire.
 CAUTION  To  store  discharged  fluid  temporarily,  place  it  in  the  included  drain  bottle  or  in 
a  durable  sealed  container  such  as  a  metal  can  or  polyethylene...

4-1 Dairy Care and Maintenance
56Chapter 4 Maintenance and Adjustment
Cleaning
 WARNING Never use gasoline, alcohol, thinner, or any other flammable material.
Doing so may cause fire.
 This machine is a precision device, and is sensitive to dust and dirt. Perform cleaning on a daily ba- sis.
 Clean by wiping with a cloth moistened by neutral detergent diluted wit\
h water then wrung dry.
 Never attempt to oil or lubricate the machine.
Care and Maintenance of the Print Heads
Daily Care and Maintenance...

57Chapter 4 Maintenance and Adjustment
4-2 When Head Cleaning Is Not Effective 
Performing More Powerful Cleaning 
When the problems such as dot drop-out are not cleared up by the "normal cleaning," try the more forceful "medium clean-
ing" or the even more forceful "powerful cleaning." Note, however, that this consumes more ink than "normal cleaning," and 
too-frequent use may damage the print heads themselves. Avoid using it more than necessary.
In the same way as for...

4-2 When Head Cleaning Is Not Effective
58Chapter 4 Maintenance and Adjustment
Check the drain bottle. 
If the amount of discharged fluid is near the upper-limit line, then remove the bottle, discard 
the collected fluid, and reattach the bottle.
 P. 54, "Disposing of Discharged Ink," step 2
Press.
The screen shown in the figure appears, then cleaning starts.
When it finishes, the screen shown in the figure appears again. Go on to Step
.
Press.
Press
to go back to the original screen.
When...