Runco Cl 610 Projector User Manual

							
31Runco CL-610 Owner’s Operating Manual

On-Screen Display Menus
Using the MenuINFORVR
ENTER
EXITMENU
T h i s   u n i t   i s   e q u i p p e d   w i t h   a n   o n - s c re e n 
display (OSD) menu for making adjustments 
and changing settings. There are five menu 
languages; see the Language setting under 
“Installation” on page 35.
•  Press the  Menu button to turn on/off the OSD menu.
  NOTE: If the Main Menu is displayed, you can also press 
Exit to turn it off.
•  Use the arrow buttons ( ▲,◄,▼,►) to select items in the menu or to make various 
adjustments.
•  Press Enter or ► to select an item to change, or press  Exit to leave and save the 
setting of items in the menu.
Main Menu
When the  Menu button is pressed, the Main Menu (shown above) appears on the 
screen. Use the ▲ or ▼ button to move to an item, then press  Enter to select it.
The active source is indicated by an arrow (>) to the left of the source; in the example 
above, Video is the active source. To select a different source, use the ▲ or ▼ button 
to highlight it and press Enter or  ►.  
Runco CL-610
>  Video
  S-Video
  Component1
  Component2
  RGB-HD
  HDMI
------------------------
  Aspect Ratio
  Installation
  Option
  Set Up
  ISF Calibration
Source selection and picture quality adjustments
Aspect Ratio selection
Option selection
Setup selection
ISF Calibration selection Installation selection 
						

							
32Runco CL-610 Owner’s Operating Manual

On-Screen Display Menus
Picture Quality 
Adjustments
To access the picture quality adjustments, press Menu, highlight the active source and 
press  Enter  or ►. The picture quality sub-menu then appears (see above).
To adjust a setting, highlight it with the 
▲  or ▼ button and press  Enter to activate a 
scroll bar for that setting. Use the ◄ or ► keys to change the setting. When finished, 
press  Exit. 
Select  Brightness  to adjust the black level of the projected image (0 = minimum;  
60 = maximum). 
Select Contrast  to adjust the white level of the projected image (0 = minimum;  
32 = maximum). 
Select Color to adjust the color level (saturation) of the projected image (0 = minimum;  
64 = maximum).
Select  Tint to adjust the hue of the projected image (0 = minimum; 30 = maximum).
Select  Sharpness  to adjust the sharpness of the projected image (-14 = minimum; 
+20 = maximum). This setting has no effect if the Sharpness Filter is set to 0 (refer to 
the next paragraph). 
The Filter  setting controls the behavior of the Sharpness control. The available 
s e t t i n g s   d e p e n d   o n   t h e   v e r t i c a l   re s o l u t i o n   o f   t h e   i n p u t   s i g n a l ,   a s   f o l l o w s : 
• With a 480i signal , you can apply the sharpness control to either the input signal 
(1), the output signal (2), both (3) or neither (0).
• With a 480p or higher-resolution signal,  the sharpness control is applied only 
to the output signal and only when you set the Sharpness filter to “on” (1).
Runco CL-610
> Video
  S-Video
  Component1
  Component2
  RGB-HD
  HDMI
------------------------
  Aspect Ratio
  Installation
  Option
  Setup
  ISF CalibrationAdjustment
Brightness
Contrast
Color
T int
Sharpness
Filter
Color Temperature
ICC Selection
Store Image Settings 
Restore Image Settings
Brightness ➤
 
Contrast ➤
Color ➤
 
Tint ➤
Sharpness ➤
 
Filter ➤ 
						

							
33Runco CL-610 Owner’s Operating Manual

The CL-610 has six memory settings for Color Temperature. Four of these settings 
are factory set to default as follows:
 0 -- Original lamp color temperature
 1 -- 5400 kelvins
 2 -- 6500 kelvins
 3 -- 8500 kelvins
 4 -- Custom
 5 -- Custom
Custom 4 and 5 memory are installer-adjustable and can be used to create custom 
settings. There are nine adjustable “white balance” parameters available for the Custom 
4 and 5 settings (three each for red, green and blue). These are described later in this 
section; refer to “Set Up.”
NOTE: You must enter a passcode in order to enter the Set Up menu. 
Use the  ICC Selection  menu to select the color space that is appropriate for the 
source signal, to achieve optimal color balance.
NOTE: The International Color Consortium (ICC) is a group of imaging product vendors 
that promotes and develops cross-platform, vendor-neutral color measurement and 
management standards.  
If you select NTSC, HDTV or PAL, you can make further adjustments to individual color 
characteristics in the  ICC Adjust sub-menu under the  ISF Calibration menu, described 
later in this section. (The Standard color is factory-set and not adjustable.)
 
Once the desired adjustments have been entered, select  Store Image Settings to 
save these settings into the “Memory 1” memory location.
To recall stored custom image quality settings, select  Restore Image Settings and 
choose “Memory 1,” “ISF Night” or “ISF Day.”
➤ Color Temperature
Color Temperature
   2  -           +
On-Screen Display Menus
➤ Store Image Settings 
➤ Restore Image Settings 
➤ ICC Selection 
						

							
34Runco CL-610 Owner’s Operating Manual

Aspect Ratio
To access the Aspect Ratio adjustments, press Menu, then press the ▲ or ▼ arrows 
to highlight  Aspect Ratio  and press Enter. The Aspect Ratio sub-menu then appears 
(see above).
There are six aspect ratios available that can be selected for video signal inputs:
Aspect Ratio
Anamorphic (16:9)
 
Standard (4:3) 
Letterbox
Virtual Wide
Cinema
Virtual Cinema
Runco CL-610
>   Video
  S-Video
  Component1
  Component2
  RGB-HD
  HDMI
------------------------
  Aspect Ratio
  Installation
  Option
  Setup
  ISF Calibration
Active Image Area
Ac tive 
Image Area
Active Image Area
• ANAMORPHIC (16:9)
The  image  is  compressed  vertically, 
but anamorphic software will appear 
properly  proportioned.  This  is  best 
suited for use with 16:9 DVDs and HDTV 
programming.
• STANDARD (4 x 3)
The input signal is scaled to fit in the 
center of the 16:9 screen. • LETTERBOX
The  image  in  the  Letterbox  mode  is 
stretched  vertically,  and  the  top  and 
bottom portion ‘blanked off’. This ratio 
is best suited for LaserDisc movies or 
non-anamorphic DVDs.
• VIRTUALWIDE
A 4:3 image is transformed into a 16x9 
image.
On-Screen Display Menus 
						

							
35Runco CL-610 Owner’s Operating Manual

On-Screen Display Menus
• CINEMA
The  image  in  the  Letterbox  mode  is 
enlarged to a 16x9 image and the upper 
and lower portions are compressed.
• VIRTUAL CINEMA
A 2.35 image is stretched vertically in 
both directions to fill a 16:9 image.
Aspect Ratio (continued)
Runco CL-610
>  Video
  S-Video
  Component1
  Component2
  RGB-HD
  HDMI
------------------------
  Aspect Ratio
  Installation
  Option
  Setup
  ISF Calibration
Installation
Language
Picture Orientation 
Keystone Adjust 
Background Color
RS-232 Baud Rate 
Blue Image
Installation
To access the Installation adjustments, press  Menu, then press the ▲ or  ▼ arrows 
to highlight  Installation  and press Enter. The Installation sub-menu will then appear 
(see above). Press the  Exit button to return to the previous menu or press the  Menu 
button to close all menus.
NOTE: When you change a setting in the Installation menu, the change takes effect 
immediately; you do not need to press Enter afterwards. (Press Exit to return to the 
previous menu or Menu to exit.) 
						

							
36Runco CL-610 Owner’s Operating Manual

Language
> English    
  Francais
  Espanol
  Deutsch
  Italiano
Press the ▲  or  ▼ arrows to select from the available 
Languages :  English,  French,  Spanish,  German  and 
Italian.
Picture Orientation
> Floor Front    
  Ceiling Front
  Floor Rear
  Ceiling Rear
Keystone Adjust
   -              +      0
Background Color
>  Blue    
  White
RS-232 Baud Rate
>  9600
  38400
  115200
Blue Image
>  Off
  On
Language ➤
Picture Orientation ➤
Keystone Adjust ➤
Background Color ➤
RS-232 Baud Rate ➤
Blue Image ➤
On-Screen Display Menus
Press the 
▲ or  ▼ arrows to select the projector’s  Picture 
Orientation. The projector can be installed on a ceiling 
or in a rear-screen configuration with one or more mirrors. 
There are four settings: Floor Front, Ceiling Front, Floor Rear 
and Ceiling Rear.
To correct distortion resulting from the angle of the projection, 
select Keystone Adjust  and use the ◄ or  ► arrows to 
make the image rectangular.
NOTE: Runco recommends that the keystone feature not be 
used unless absolutely necessary, as it may cause artifacts 
in the image.
Press the ▲ or  ▼ arrows to select the image  Background 
Color (blue or white). The Background Color appears when 
no incoming signal is present.
Press the ▲ or  ▼ arrows to select the projector’s  RS-232 
Baud Rate. This function is used to change the transfer 
rate of the RS-232 connection. (This setting must match the 
data rate of the device connected to the RS-232 input.)
Press the ▲ or  ▼ arrows to turn the  Blue Image Off or On. 
This feature removes all red and green color information from 
the image, and is useful for color-calibrating the projector 
or other video components.  
						

							
37Runco CL-610 Owner’s Operating Manual

Runco CL-610
>  Video
  S-Video
  Component1
  Component2
  RGB-HD
  HDMI
------------------------
  Aspect Ratio
  Installation
  Option
  Setup
  ISF Calibration
Option
Reset Image Settings
Sleep T imer
Lamp Hours
OSD T imer
OSD Position
PC & HD Adjust
PIP/PBP Set Up
DNR
On-Screen Display Menus
Option
To access the Option adjustments, press  Menu, then press the ▲ or  ▼ arrows to 
highlight  Option and press  Enter. The Option sub-menu will then appear (see above). 
Press the  Exit button to return to the previous menu or press the  Menu button to 
close all menus.
Reset Image Settings
Load default of current source
Confirm?
No                  Yes
Sleep Timer
   -         0  +   Minutes
Lamp Hours
         +8     Hours
       +30     Minutes
OSD Timer
   +60  -           +
OSD Position
Hor.                         
0
Ver.                        +20
To restore the default image settings for the current input 
source ONLY, press the  ► arrow key to highlight “Yes” then 
press  Enter.
The Sleep Timer automatically puts the projector into standby 
mode after the amount of time you specify here. (A warning 
appears on-screen one minute before this is to occur.) 
Press the ◄ or  ► arrows to set the timer for anywhere from 
10 minutes to 3 hours, in 10-minute increments. To disable 
the Sleep T imer, set it to 0. 
Press the  Enter button to check the total time of lamp 
usage.
Press the ◄ or  ► arrows to set the OSD T imer. This 
timer controls how long the menus remain on-screen after 
selecting them. Select from 0 to 60 seconds, in 3-second 
increments. When you set the OSD to 0, the menus remain 
on-screen until you hide them by pressing  Menu.
Press the ◄ or  ► arrows to adjust the horizontal and vertical 
position of the OSD. 
➤ Reset Image Settings
➤ Sleep Timer
➤ Lamp Hours
➤ OSD Timer
➤ OSD Position 
						

							
38Runco CL-610 Owner’s Operating Manual

On-Screen Display Menus
PC & HD Adjust
Auto       Yes?
Freq.           0
Phase       +10
H.Pos.           0
V.Pos.           0
Press  Enter to display the  PC & HD Adjust  menu. Use these 
settings to fine-tune 480p and higher-resolution signals for 
optimum picture quality.
• Auto:  Adjusts  the  phase,  frequency  and  position 
automatically.
•  Freq.:  Adjusts the frequency of the signal.
• Phase:  Adjusts the phase of the input signal (similar to 
tracking on a VCR).
•  H. Pos.:  Adjusts the horizontal position of the image.
•  V. Pos.:  Adjusts the vertical position of the image.
NOTE: To adjust the image position with a 480i source, use 
the Image Shift controls in the Set Up menu, described on 
page 41.
PIP/PBP Set Up
PIP/PBP Enable
PIP Set Up
PBP Set Up
PIP/PBP Enable
Off
On
PIP Set Up
PIP Off
Graphic in Video
Video in GraphicPIP/PBP Set Up
PIP/PBP Enable
PIP Set Up
PBP Set Up
PBP Set Up
PBP Off
Graphic by Video
Video by GraphicPIP/PBP Set Up
PIP/PBP Enable
PIP Set Up
PBP Set Up
PC & HD Adjust ➤
PIP / PBP Set Up ➤Press the ▲  or  ▼ arrows to select  PIP/PBP Enable , then press Enter.
Press the 
▲  or  ▼ arrows to select  Off or  On, then press  Enter.
Press the 
▲  or  ▼ arrows to select  PIP Set Up, then press  Enter.
Press the 
▲  or  ▼ arrows to select  PIP Off, Graphic in Video  or Video in 
Graphic , then press  Enter
.
PIP Set Up ➤
PBP Set Up ➤Press the ▲ or  ▼ arrows to select  PBP Set Up, then press Enter.
Press the 
▲  or  ▼ arrows to select  PBP Off, Graphic by Video  or Video by 
Graphic , then press  Enter
.
  -             +      0
Press the ◄  or  ► arrows to adjust the Digital Noise Reduction ( DNR). DNR is useful 
for clearing up noisy RGB images such as those from a PC. Adjust as desired, keeping 
in mind that reducing noise (which reduces high frequencies) may also soften the 
image.
DNR ➤ 
						

							
39Runco CL-610 Owner’s Operating Manual

On-Screen Display Menus
SetupTo access advanced picture quality adjustments, use the up- or down-arrow keys to 
highlight Set Up and press  Enter. Use the number buttons on the remote to enter the 
Set Up menu passcode when prompted and press  Enter again. Then, press MENU 
on the remote control. 
Runco CL-610
>  Video
  S-Video
  Component1
  Component2
  RGB-HD
  HDMI
------------------------
  Aspect Ratio
  Installation
  Option
  Set Up
  ISF Calibration
Passcode
Please Enter
Passcode To
Access Service Screen
* * *
Passcode
Please Enter
Passcode To
Access Service Screen
Confirmed
➤ White Balance
NOTE: You only need to enter the Set Up menu passcode the first time you select that 
menu after turning on the projector. 
Gamma:  “Gamma” is a global setting that determines how gray shades are displayed 
between minimum input (black) and maximum input (white) for all signals. A good 
gamma setting helps to optimize blacks and whites while ensuring smooth transitions 
for the “in-between” values utilized in other grays. Unlike “Brightness” and “Contrast” 
controls, the overall tone of your images can be lightened or darkened without changing 
the extremes and all images will be more vibrant while still showing good detail in dark 
areas when using the “Gamma” control.
In all but the most unusual situations, the appropriate “Gamma Selection” (see below) 
will produce accurate colors and a satisfying contrast level. However, it is sometimes 
necessary to adjust the red, blue and green gamma curves individually. To do this, 
select Gamma from the White Balance sub-menu and use the left- and right-arrow 
buttons to manipulate the on-screen slidebars.
Gain: Use the Gain controls in the White Balance sub-menu to correct color imbalances 
in the bright areas of the image. A good way to do this is to use a test pattern consisting 
mostly of solid white areas, such as an 80 IRE “window” pattern. If the white areas 
contain traces of red, green or blue, decrease the Gain for that color.
Offset:  Use the Offset controls in the White Balance sub-menu to correct color 
imbalances in the dark areas of the image. A good way to do this is to use a test pattern 
consisting mostly of dark gray areas, such as a 30 IRE “window” pattern. If the gray 
areas contain traces of red, green or blue, decrease the Offset for that color.
Store Color Temp.4/Store Color Temp.5:  When you are finished adjusting the 
Gamma, Gain and Offset, select Store Color Temp.4 or Store Color Temp.5 to store 
your settings. To recall them, set the Color Temperature to +4 or +5 in the Image 
Adjustment menu (refer to “Picture Quality Adjustments,” earlier in this section). 
						

							
40Runco CL-610 Owner’s Operating Manual

On-Screen Display Menus
The normal gamma setting of 2.2 is correct for almost all 
signals and conditions. If excess ambient light washes out the 
image and it becomes difficult or impossible to see details in 
dark areas, lower the gamma setting to compensate. This will 
improve contrast while maintaining good details for blacks. 
Conversely, if the image is washed out and unnatural, with 
excessive detail in black areas, increase the setting. Again, 
good gamma improves contrast while maintaining good details 
for blacks and whites.
The SD Enhance menu gives you options for improving 
the quality of standard-definition, 480i images. (For 480p 
and higher-definition images, the controls in this menu are 
disabled.) Keep in mind that these controls add frequencies 
that are not present in the original signal, and may make 
images appear “noisy” if misused. 
H Enhance/V Enhance: These controls can improve the 
apparent horizontal and/or vertical resolution of the image. 
Chroma  Enhance: This  control  adds  chroma  (color 
information) to the input signal and can make colors appear 
more vibrant and saturated. 
H Threshold/V Threshold/Chroma Threshold:  Set these to 
+11 or higher to activate the enhancement controls described 
above. Generally, the higher the threshold, the more noticeable 
the enhancements you make will be. 
Image Over Scan pushes the outside edge of the active 
picture area of the video signal out beyond the edge of the 
display area. 
Some  television  programs  are  produced  based  on  the 
assumption that older television sets may not display the outer 
edges of the broadcast picture area. Over scan effectively trims 
away these inactive, outer edges and enlarges the remaining 
portion of the image to fill the display area.
Select from 1% to 10% of Over Scan, as desired.
For HDTV, DVDs and other video sources, Over Scan is 
generally not necessary or desirable.
The Image Shift menu allows you to precisely center the 
image on the screen. (These controls are available only with 
a 480i source signal.)
Horizontal: This control moves the image right or left within 
the area of available pixels. 
Vertical: This option moves the image up or down within the 
area of available pixels.
Gamma Selection ➤
 
Gamma Selection
2.8
2.5
2.2
1.0
RUNCO Enhance 1
RUNCO Enhance 2
ISF Day
Image Over Scan
                         +4 %
H Enhance
V Enhance
Chroma Enhance
H Threshold
V Threshold
Chroma ThresholdSD Enhance ➤
Image Over Scan ➤
Horizontal
Vertical
  -                    +       0
Image Shift ➤