Runco Cl 710 Projector User Manual

							6. Additional Information
Runco CL-710/ CL-710LT User’s Manual28
Troubleshooting
7. Put on the front 
lamp cover. 8. Tighten the screw of 
front lamp cover.
9.  Turn on the power and  go into the Set Up menu 
to reset the Lamp 
Timer item.
Problem Possible Cause Remedy
This unit does not 
turn on. There is no power from power cable. Plug the power cord into the AC inlet on the 
rear of this unit, and plug the power cord into 
to the power inlet.
The power switch is not turned on. Turn on the power switch.
Turn on this unit again within the 
cooling down procedure. Wait this unit complete the cooling down 
procedure.
Front lamp cover is not attached well. C orrectly attach the front lamp cover.
No picture The front lamp cover is not correctly  attached. Correctly attach the front lamp cover.
This unit is not correctly connected to 
the input source device. Check the connection.
The input signal has not been correctly 
selected. Select the correct input signal with the input 
keys: Video, S-Video, Component, Component 
HD, RGB HD and DVI-I on the remote control.
POWER LED or LAMP LED blinking. Please contact your Runco dealer for  assistance.
Image is unstable The co nnection cables are not 
connected to this unit. Correctly connect the cables to the 
appropriate terminals.
Picture is blurred The projection lens is not correctly  focused. Adjust the focus of projection lens with the 
focus ring.
This unit and the screen are not placed 
squarely. (90 degree) Adjust the projection an
gle and direction, and 
the height of this unit.
Remote control does 
not work correctly The batteries are exhausted.  Replace both batteries with new ones.
LAMP LED blink in red The front lamp cover is not correctly  attached. Correctly attach the front lamp cover.
The cooling fan does not work well. Please contact your Runco dealer for  assistance. 
The temperature inside this unit is 
extremely high. Check that the ventilation holes are not 
blocked.
POWER LED blink in 
orange and green 
sequentially The lamp has exceed its specified 
usage hours.
Replace the lamp with a new one.
The lamp has burned out. Replace the lamp with a new one. 
						

							6. Additional Information
Runco CL-710/ CL-710LT User’s Manual29
Specifications 
CL-710/ CL-710LT Specifications
Projector Type
:  Digital Light Processing™ (DLP™), Single HD-2 DMD Chip
Native Resolution:   1280 x 720, (16:9)
Aspect Ratios: 4:3, Letterbox, 16:9, Anamorphic, Virtual Wide
Video Standards: NTSC, PAL
DTV Compatibility: 480p, 720p, 1080i
Scan Frequency:  Horizontal: 15-80 kHz
Vertical: 50-100 Hz
Picture Size (16:9 Screen): Recommended Width: 72-96 in.            
Maximum Width:  200 in. 
Throw Distance CL-710: 1.40 to 1.60/ CL-710LT: 1.85 to 2.40
(Factor x Screen Width) :Please refer to page 11 to page 14.
Light Output:  1000 ANSI Lumens*                            
CSMS** Specifications: 
Home Theater Calibration: 
489 ANSI Lumens  
18.1 Foot-Lamberts (fL)
Contrast Ratio: 1800:1
CSMS** Contrast Ratio: 156:1
Lamp: 210W 
Lamp Life: 1000 hours @ 6500
o Ke l v i n
Inputs: (1) Composite Video, (1) S-Video, 
(1) RGB/Component (via BNC), 
(1) RCA Component Video, 
(1) DVI w/ HDCP, (1) RS-232
Memories:  21 memories
12V Output: Max .250 Amp, active when the projector is on
Power Requirements: 100-240V AC, 50/60 Hz, 310 watts
Operating Environment: 41°- 95° F, (5°- 35° C), 20%-80% Humidity (non-condensing)
Dimensions  (w/out feet): Width: 16.15 in. (410.16 mm), 
Depth: 14.56 in. (369.71 mm),
Height: Without feet 5.3 in. (134.62mm) 
with feet 5.8 in. (148.62 mm)            
Weight: 22 lbs. (10 kg) (includes lens)
Regulatory Approvals: UL, CSA, GS-TUV, CCIB, CB, 
FCC, CE, VCCI and C-Tick
Limited Warranty:  Projector:
 (2) Two year parts and 
labor from the date of 
delivery to the end user 
Lamp Warranty:
  1000 hours or 
(6) six months, which ever comes first. 
						

							6. Additional Information Runco CL-710/ CL-710LT User’s Manual30*ANSI Lumen specification:
This is the typical projector luminosity (brightness) specification found in most sales literature.  This measurement is 
included in RUNCO literature to allow for direct comparison with other manufacturers projectors.  These 
measurements can be taken at 9,000 to 13,000 degree Kelvin to get expected performance data when the projector is 
used in professional, commercial, and industrial displays.
**CSMS Home Theater Calibration ANSI Lumen Specification:
These measurements are taken from the projector as setup in a home theater environment. The projector is calibrated 
to ISF specifications including setting the color temperature to 6500 degree Kelvin, the standard for reproducing video.
**CSMS Home Theater Calibration foot-Lambert (fL) Specification:
This is the unit of measurement used in commercial movie theaters to express image brightness. The Society of Motion 
Picture and Television Engineers (SMPTE) specifies 16 fL as the target image brightness for film-based projectors using 
an open gate (without film in the projector).  More importantly, today SMPTE specifies 12 fL as the target image 
brightness in Digital Cinema theaters using DLP(tm) technology. The foot-Lambert is dependant on screen size, screen 
gain, and projector light output.
All measurements are made at RUNCO to ANSI/NAPM IT7.228-1997 specifications using the Photo Research PR-650 
SpectraColorimeter and Minolta LS-100 Light Meter, Video Essentials test DVD, and a Stewart Filmscreen StudioTech 
130, 1.3 gain, 72-inch wide screen. The projector is calibrated to a color temperature of 6500
 o  Kelvin and has a 
minimum of 150 hours of usage. 
						

							6. Additional Information Runco CL-710/ CL-710LT User’s Manual31
Dimensions 
Unit: in. (mm) 
						

							6. Additional Information Runco CL-710/ CL-710LT User’s Manual32
RS-232 Setup
Baud Rate: 115200 or 9600
Parity: None
Data Bits: 8 Bits
Stop Bits: 1 Bit
Flow Control: None
RS-232C Control Codes 
Code Function
X01 Power On
X02 Power Off
X03 Message On
X04 Message Off
X10 Menu (arrow key)
X11 Enter (arrow key)
X12 Exit (arrow key)
X13 Up (arrow key)
X14 Down (arrow key)
X15 Left (arrow key)
X16 Right (arrow key)
X20 Switch to Composite input
X21 Switch to S-Video input
X22 Switch to Component input
X23 Switch to D-Sub _PC input
X24 Switch to YPBPR input
X25 Switch to BNC_PC input
X35 Anamorphic
X36 Standard
X37 Letter box
X38 Virtual Wide
X40 Load memory 1 settings
X41 Load memory 2 settings
X42 Load memory 3 settings
X46 Load default of current source
X47 Save memory 1 settings
X48 Save memory 2 settings
X49 Save memory 3 settings
X55 Switch active source
X56 Picture in picture display
X57 Picture in picture display
X60 Switch language - English
X61 Switch language - French
X62 Switch language - Spanish
X85 PC Input - auto
X90 Image orientation - floor front
X91 Image orientation - ceiling front
X92 Image orientation - floor rear
X93 Image orientation - ceiling rear
X94 Back light on
X95 Back light off
PC Out Adapter
1. Connect D-Sub 9-pin female to RJ-11 adapter (not 
included) to Com port on PC.
2. Connect RJ-11 to Projector. 
Wa r n i n g: During initial turn on and turn off of the 
projector, this unit will not accept RS-232 codes for 20 
seconds.
NOTE:
1. All codes are in the ASCII format.
2. A carriage return is required after each command.
RS-232 For RJ-11 (not included)
4-pin RJ-11 Details
2TxT
3RxD
1, 4 Ground
12345
7896
RS-232 For D-Sub 9-pin (not included)
D-Sub 9-pin female Details
2TxT
3RxD
5 Ground
1, 4, 6, 7, 8, 9 NC
D-Sub 9-pin female RJ-11 to D-Sub 9-pin (not included)
1234
Yellow
Ye l l o w
RedRedBlack Green
Green
Black 
						

							RUM A-010100 rev 7-03
R unco  In te rn atio nal .2 900 F aber Str e et .U nio nC it y,  C A94587 .ph ( 5 10 ) 3 24-7 777 .fa x ( 5 10 ) 3 24-9 300 .w ww.r u nco .c o m