Runco Rs 1100 Projector User Manual

Installation
Runco RS-1100 Series Owner’s Operating Manual 39 
PREL
IMINARY
4. When the height is properly set, tighten the Height Adjustment Screws to secure the 
lens in place.
Adjusting the Pitch (Angle): Next, angle the lens to even out any top-to-bottom 
pincushion distortion. To do this, loosen the Pitch Adjustment Screws on either side of the 
lens to allow it to pivot freely. Then, adjust the anamorphic lens angle so that the projected 
image is rectangular: 
The anamorphic lens will almost...

Installation
40 Runco RS-1100 Series Owner’s Operating Manual
PREL
IMINARY
your projector may differ slightly from what is shown in these instructions. 
Figure 3-19. RS-1100 Ultra Anamorphic Lens Mounting Assembly - Exploded 
View
1. Use the Lens Rotation Set Screws (item #2) to attach the Lens Adapter Ring (item #8) 
to the Pitch Adjustment Yoke (item #7). (Use the curved, oval-shaped holes on the 
Pitch Adjustment Yoke.)
2. Attach the Mounting Bracket (item #1) to the front of the projector with the...

Installation
Runco RS-1100 Series Owner’s Operating Manual 41 
PREL
IMINARY
4. Attach the Anamorphic Lens (item #9) to the Lens Adapter Ring by threading it 
clockwise.
 
 
Adjusting the Lens Height (Y): 
1. Project a white field on the screen.
2. Ensure that the Height/Y-Adjustment T-Screws and Pitch Adjustment T-Screws are 
loose enough to allow vertical movement of the lens assembly. 
3. Slowly move the anamorphic lens into place so that there are no shadows on the top 
or bottom of the screen: 
4....

Installation
42 Runco RS-1100 Series Owner’s Operating Manual
PREL
IMINARY
The anamorphic lens will almost always be angled with respect to the projector; this is 
normal. Once the proper lens angle has been set, firmly tighten the Pitch Adjustment 
T-Screws to secure the lens in place.
Geometry: 
1. Input an anamorphic cross-hatch test pattern to the projector.
2. Loosen the three Lens Rotation Set Screws (shown in Figure 3-19) on the lens 
adapter plate just enough to allow it to rotate freely.
3....

Runco RS-1100 Series Owner’s Operating Manual 43 
PREL
IMINARY
4.1 
Selecting Video 
Memory
 Press the MEM1 button on the remote control 
to recall settings for the current input from the 
“Memory 1” memory preset. 
 Press ISF NIGHT to recall settings for the current input from the “ISF Night” memory 
preset. 
 Press ISF DAY to recall settings for the current input from the “ISF Day” memory 
preset. 
 Press FACT to recall the factory-default settings for the current input. 
4.2 
Selecting an Aspect...

Operation
44 Runco RS-1100 Series Owner’s Operating Manual
PREL
IMINARY
4.5 
Using 
Picture-In-Picture/
 
Picture-By-Picture 
(PIP/PBP)
For PIP and PBP purposes, there are two groups 
of inputs separated by their display modes: 
 Video (SD) group: Video, S-Video and 
Component
 1 inputs. 
 Graphic (HD) group:  HDMI and 
Component
 2/RGB inputs. 
PIP / PBP shows one input from the Graphic group within or beside one input from the 
Video group. 
 Press PBP to enable the PBP function. Press PBP again to...

Operation
Runco RS-1100 Series Owner’s Operating Manual 45 
PREL
IMINARY
Figure 4-1. RS-1100 OSD Menu Structure
Video
S-Video
Component1
Component2
RGB-HD
HDMI
Brightness 0 ... 60 
Contrast 0 ... 32
Color 0 ... 64
Tint 0 ... 30
Sharpness -14 ... 0 ... +25
Filter 0, 1, 2 or 3
Color Temperature5400 K, 6500 K, 8500 K, 
Custom 1 or Custom 2
ICC SelectionStandard, NTSC, HDTV or 
PAL
Store Image Settings Memory 1
Restore Image 
SettingsMemory 1, ISF Night or 
ISF Day
Aspect Ratio
Anamorphic (16:9)
Standard...

Operation
46 Runco RS-1100 Series Owner’s Operating Manual
PREL
IMINARY
Main MenuThe Main Menu is the starting point for accessing all projector functions. 
(The Set Up and ISF Calibration menus are hidden and not accessible until you enter a 
passcode.)
The active source is indicated by an arrow (>) to its left; in the example at left, Video is the 
active source. To select a different source, use the 
 or  button to highlight it and press 
ENTER or . 
Picture AdjustmentUse the controls in the...

Operation
Runco RS-1100 Series Owner’s Operating Manual 47 
PREL
IMINARY
Although it may be possible to obtain satisfactory picture quality using the naked eye and 
regular program material, Runco recommends using the following calibration tools for best 
results: 
 External test pattern source – Ovation Multimedia, Digital Video Essentials or AVIA test 
DVD or equivalent.
 A blue filter (provided with many test DVDs), for color level and tint adjustments.
Connect your test pattern source to the input...

Operation
48 Runco RS-1100 Series Owner’s Operating Manual
PREL
IMINARY
Contrast: On your external test pattern source, select a stepped, gray-bar pattern like the 
one shown in 
Figure 4-3. 
Figure 4-3. Typical Gray Bar Pattern for Adjusting Contrast
Select Contrast from the Adjustment menu and press ENTER. Adjust the contrast to a 
point just below which the white rectangle starts to increase in size.
Color Saturation: On your external test pattern source, select a color bar pattern like the 
one shown...