Runco Television XP-65 User Manual

Controls and Functions
CinemaWall XP-50/XP-65 Installation/Operation Manual 7 
PREL
IMINARY
ConnectorsFigure 2-3 shows the rear-panel connector locations on the CinemaWall. 
Figure 2-3. CinemaWall Rear Panel
1.SLOT 1 (Dual HDMI input) 
Two, HDCP-compliant digital video inputs.
2.SLOT 2 (Dual HDMI input) 
Two, HDCP-compliant digital video inputs.
SERIAL PC    IN
AUDIO
SLOT1
PR/CR/R PB/CB/BY/GAUDIORLCOMPONENT/RGB IN
SLOT2 SLOT3
AV IN
AB
AV IN
AB
XP-50
12345
XP-65
6
6 

Controls and Functions
8 CinemaWall XP-50/XP-65 Installation/Operation Manual
PREL
IMINARY
3.SLOT 3 (COMPONENT/RGB input) 
Video/audio input (3 x BNC, 2 x RCA) for connecting either RGB (with sync on green) 
or component high-definition television signals. 
4.PC IN  
Provides a 15-pin VGA connection and a 3.5-mm, stereo audio connection to a 
personal computer. The CinemaWall automatically detects the signal resolution.
5.SERIAL 
A male, 9-pin D-sub connector for interfacing with a PC or home theater...

Controls and Functions
CinemaWall XP-50/XP-65 Installation/Operation Manual 9 
PREL
IMINARY
2.2 
CinemaWall Remote 
Control
Figure 2-4 shows the CinemaWall remote control and describes its functionality.
Figure 2-4. CinemaWall Remote Control
RESET RETURN
30 60
090
OFF  TIMER  90 
1
2
3 4PC 4:3
10:00
1
2
3
4
ON SURROUND
SURROUND button
Press the SURROUND button to turn surround-sound mode on or off.
Note:
The surround settings are memorized separately for each AUDIO MENU setting 
(STANDARD, DYNAMIC,...

Controls and Functions
10 CinemaWall XP-50/XP-65 Installation/Operation Manual
PREL
IMINARY
Notes: 

CinemaWall XP-50/XP-65 Installation/Operation Manual 11 
PREL
IMINARY
3.1 
Remote Control
To install batteries in the remote control: 
1. Press on the tab on the battery compartment cover and lift the cover in the direction 
of the arrow. 
2. Insert the included batteries. Ensure that the polarities correctly match the  and  
markings inside the battery compartment.
3. Close the battery compartment cover and press the tab on the cover until it clicks in 
place.
 
Notes on Batteries When installing...

Installation
12 CinemaWall XP-50/XP-65 Installation/Operation Manual
PREL
IMINARY
3.2 
Quick Setup
Table 3-1 gives a quick overview of the CinemaWall installation process. The sections 
following this one provide detailed instructions.
Installation should be performed by a qualified custom video 
installation specialist.
Table 3-1. Installation Overview 
StepProcedureFor Details, refer to 
page...
1Mount the CinemaWall on a wall or table stand13
2Connect signal sources to the CinemaWall16
3Connect...

Installation
CinemaWall XP-50/XP-65 Installation/Operation Manual 13 
PREL
IMINARY
3.3 
Installation 
Considerations
Proper installation of your CinemaWall will ensure the highest possible picture quality. 
Whether you are installing the CinemaWall temporarily or permanently, you should take 
the following into account to ensure that it performs optimally.
High-Altitude OperationDue to the design of all plasma glass panels made by every manufacturer, and the 
interaction between ambient air pressure and...

Installation
14 CinemaWall XP-50/XP-65 Installation/Operation Manual
PREL
IMINARY
 As it lies flat with the screen face 
down. Place the protective sheet, 
which was wrapped around the 
plasma monitor when it was 
packaged, between the screen and 
your work surface to avoid 
scratching or otherwise damaging 
the screen surface. 
Ambient LightIn general, minimize or eliminate light sources directed at the display. Contrast ratio in your 
images will be noticeably reduced if light directly strikes the...

Installation
CinemaWall XP-50/XP-65 Installation/Operation Manual 15 
PREL
IMINARY
Other ConsiderationsHere are some other considerations and tips that can help improve your installation, avoid 
damage and prolong operating life: 
 Keep the ambient temperature constant and below 35°C (95°F). Keep the display away 
from heating and/or air conditioning vents. Changes in temperature may cause drifts in 
the display circuitry, which may affect performance.
 Keep the CinemaWall away from devices that radiate...

Installation
16 CinemaWall XP-50/XP-65 Installation/Operation Manual
PREL
IMINARY
3.4 
Connections to the 
CinemaWall
Proceed as follows to connect the CinemaWall to your video sources, external controller(s) 
– if present – and AC power. 
When connecting your equipment:
 Turn off all equipment before making any connections.
 Use the correct signal cables (sold separately) for each source. 
 Ensure that the cables are securely connected. Tighten the thumbscrews on 
connectors that have them. 
Connecting...