Runco XP-50DHD Plasma Display User Manual
Have a look at the manual Runco XP-50DHD Plasma Display User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 123 Runco manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Installation PlasmaWall XP Series Installation/Operation Manual 25 PREL IMINARY Component Video Source Connections: Connect your component video sources to the HD1, HD2 and/or Component/SCART inputs as shown in Figure 3-7. Figure 3-7. Component Video Source Connections Y PBPR COMPONEN T VIDEO OUT BD/DVD DTV-Set-Top Box (DTV-STB) RCA-to-BNC adapter
Installation 26 PlasmaWall XP Series Installation/Operation Manual PREL IMINARY RGBHV Source Connections: Connect personal computers and/or other RGB sources to the HD1, HD2 and/or Component/SCART inputs as shown in Figure 3-8. Figure 3-8. RGBHV Source Connections or ComputerRGB Camcorder BNC-to-RCA adapter Green Blue Red H-Sync V-Sync Green H-Sync Blue V-Sync Red
Installation PlasmaWall XP Series Installation/Operation Manual 27 PREL IMINARY SCART RGBS Source Connections: Connect the green, blue and red outputs from your SCART source to the Component/SCART input on the DHD Controller. Connect the sync output from your SCART source to the Video input on the DHD Controller. See Figure 3-9. Figure 3-9. SCART RGBS Source Connections Gaming ConsoleVCR DVD/DTV STB SCART-to-RGBS adapter Green Blue Red Sync Green Blue Red Sync
Installation 28 PlasmaWall XP Series Installation/Operation Manual PREL IMINARY Composite and S-Video Source Connections: See Figure 3-10. Figure 3-10. S-Video and Composite Video Source Connections Gaming ConsoleVCR Camcorder Composite S-Video S-Video Composite S-Video S-Video
Installation PlasmaWall XP Series Installation/Operation Manual 29 PREL IMINARY RS-232 Controller Connection Use a straight-through, 9-pin RS-232 cable to connect a PC or control/automation system (if present) to the RS-232 port on the DHD Controller; see Figure 3-11. For more information about using this connection, refer to External Control on page 63. Figure 3-11. RS-232 Control System Connection 12345 7896 to Automation/ Control System or PC2 Receive Data 3 Transmit Data 5 Ground (none of the other pins are used)
Installation 30 PlasmaWall XP Series Installation/Operation Manual PREL IMINARY Connecting 12-volt Trigger Outputs to External Equipment If your installation includes equipment that responds to 12-volt triggers, connect it to the 12-volt trigger outputs as shown in Figure 3-12. Figure 3-12. Connecting 12-volt Trigger Outputs ➤ Tip = +12V Sleeve = Ground To 12-volt trigger-activated device
Installation PlasmaWall XP Series Installation/Operation Manual 31 PREL IMINARY Connecting an External IR Receiver to the DHD Controller If infrared signals from the remote control cannot reach the DHD Controller due to excessive distance or obstructions such as walls or cabinet doors, you can connect an external IR receiver to the DHD Controller to extend the range of the remote control. See Figure 3-13. Figure 3-13. External IR Receiver Connection CUST1CUST 2SVC HDMI 1HDMI 2EXITRETURN 16 : 9 4 : 3 (3.5-mm, mini phono plug) IR Sensor IR RepeaterRemote Control
Installation 32 PlasmaWall XP Series Installation/Operation Manual PREL IMINARY Connecting AC PowerPlug the female end of the power cord into the AC receptacle on the rear of the PlasmaWall. Connect the other end to your AC power source. (The XP-103DHD requires 200-240 VAC.) Figure 3-14. AC Power Connection Similarly connect the DHD Controller to a nearby AC outlet. ➤ XP-50DHD / XP-OPAL50DHD XP-65DHD / XP-OPAL65DHD XP-103DHD (NOTE: The XP-103DHD requires 200 - 240 VAC)
PlasmaWall XP Series Installation/Operation Manual 33 PREL IMINARY 4.1 Turning on the Power 1. Turn on your source components. 2. Press the main power switch on the PlasmaWall (see Figure 2-1, Figure 2-2 or Figure 2-3). Its standby/on indicator lights red. 3. Set the main power switch at the rear of the DHD Controller (see Figure 2-6) to the “on” position. Its standby/on indicator lights amber. 4. Press the ON button on the remote control (or the ON/STANDBY ( ) button on DHD Controller front panel) to turn on the system. The power indicator on the DHD Controller lights solid blue; the standby/on indicator turns off. 5. After a brief warm-up period (approximately 10 seconds), the PlasmaWall will display an image. 4.2 Setting the Computer Display Properties To maximize image quality when using the PlasmaWall with a personal computer, you may need to adjust the display properties of your computer’s video card. To do this on a Microsoft® Windows®-based PC: 1. Choose Settings from the Windows Start Menu and click on “Control Panel.” 4. Operation
Operation 34 PlasmaWall XP Series Installation/Operation Manual PREL IMINARY 2. Double click on the Display icon. 3. Click the Settings tab on the display dialog box. 4. Set the Screen area to 1024x768 pixels. 5. Click the Advanced button and click the Monitor tab on the dialog box. Set the Refresh Frequency to 60Hz and click OK. 1. The native resolution of the PlasmaWall is 1920 x 1080. Other horizontal or vertical resolutions may be scaled upward or downward to fit the display. 2. With most computers, you can get the best picture at 1024 x 768 @ 60Hz. To prevent image retention (burn) on your display, ALWAYS use a screen saver and set it to the shortest possible time. Note WARNING