Samsung CLP 320N User Manual

Wireless network setup (CLP-325W(K)/CLP-326W only)_ 41
Setting a wireless network with the WPS button
If your machine and an access point (or wireless router) support Wi-Fi 
Protected Setup™(WPS), you can easi ly configure the wireless network 
settings by pressing the  WPS (
) button on the control panel.
 If you want to use the wireless netw ork using the infrastructure mode, 
make sure that the network cable is disconnected from the machine. 
Using the WPS (PBC) button or entering the PIN number from...

Wireless network setup (CLP-325W(K)/CLP-326W only)_ 42
Installing the machine on a wireless network with an 
access point (Windows)
Items to prepare
Ensure you have the following items ready.
•Access point
• Network-con
 nected computer
• Softw
are CD that was provided with your machine
•Th
e machine installed with  a wireless network interface
• USB c
able
Creating the infrastructure network in Windows
When the items are ready, follow the steps below:
1.Che
ck whether the USB cable is connected to the...

Wireless network setup (CLP-325W(K)/CLP-326W only)_ 43
must contact the network administrator to get the static IP 
address.
For example:
If computer’s network information is as shown below:
-IP ad
dress: 169.254.133.42
-Subn
et Mask: 255.255.0.0
Then, the machine’s network information should be as below:
-IP ad
dress: 169.254.133.  43 
-Subn
et Mask: 255.255.0.0 (Use  the computer’s subnet mask.)
-Gate
way: 169.254.133. 1
9. Whe
n the wireless network setting is completed, disconnect the USB 
cable...

Wireless network setup (CLP-325W(K)/CLP-326W only)_ 44
proper WEP key can access the network.
•Encryption: Select the encryption (None, WEP64, WEP128).
•Network Key: Enter the encryption network key value.
•Confirm Network Key: Confirm the encryption network key 
value.
•WEP Key Index: If you are using the WEP Encryption, select 
the appropriate WEP Key Index.
 The wireless network security window appears when the 
ad-hoc network has security setting.
The wireless network security window appears. Select...

Wireless network setup (CLP-325W(K)/CLP-326W only)_ 45
follow the instructions in the window.
15.After searching, the window shows the wireless network devices. 
Select the name (SSID) of the access point you are using and click 
on Next.
 When you set the wireless configuration manually, click on 
Advanced Setting.
•Enter the wireless Network Name: Enter the SSID of 
access point you want (SSID is case-sensitive).
•Operation Mode: Select Infrastructure.
•Authentication: Select an authentication type....

Wireless network setup (CLP-325W(K)/CLP-326W only)_ 46
and Signal  is Printer Self Network .
Then, click on  Next.
If you want to use other ad-hoc settings, select another wireless 
netwo
 rk from the list. 
 If you want to change ad-hoc settings click the  Advanced 
Setting button . 
• En
ter the wireless Network Name:  Enter the SSID name 
you want (SSID is case-
sensitive).
• Op
eration Mode:  Select  Ad-hoc .
• Channe
l:  Select the channel ( Aut o Setting or 2412 MHz to 
2467 MHz).
• Authentication:...

Wireless network setup (CLP-325W(K)/CLP-326W only)_ 47
For example:
•MAC Address: 
 00:15:99:41:A2:78
• IP Ad
dress: 192.0.0.192
IP setting using SetIP Program (Windows)
This program is for manually setting the network IP address of your 
machine using its MAC address to communicate with the machine. A 
MAC address is the hardware serial  number of the network interface and 
can be found in the  Network Configuration Report .
For using the SetIP program, disabl e th
 e computer firewall before...

Wireless network setup (CLP-325W(K)/CLP-326W only)_ 48
1.Check whether or not the network c able is connected to the machine. 
If not, connect the machine with a standard network cable.
2. Start a web brow
 ser such as Internet  Explorer, Safari or Firefox and 
enter your machine’s new IP address in the browser window.
For example,
3. Click on Login  on the upper right of the SyncThru™ Web Service 
website.
A log-in page appears. 
4. Type
 in the  ID and  Password  then click on  Login.
If it’s your...

Wireless network setup (CLP-325W(K)/CLP-326W only)_ 49
PC Connection Error
•The configured network address is unable to connect between your 
computer and machine.
-For a DHCP network environment
The print receives the IP address automatically (DHCP) when 
computer is configured to DHCP.
-For a Static network environment
The machine uses the static address when the computer is 
configured to static address.
For example:
If computer’s network information is as shown below:
-IP address: 169.254.133.42...

Basic setup_ 50
5.basic setup
After installation is complete, you may want  to set the machine’s default settings. Refer to the next section if you would like 
to set or change values. This chapter gives you step-by-step in structions for setting up the machine.
This chapter includes:
•Altitude adjustment
• Setting the default tray and paper •
Using the power saving feature
• Changing font setting (CLP-320N(K)/CLP-321N/CLP-325W(K)/ 
/CLP-326W only)
  
Altitude adjustment
The print quality is affected by...