Samsung CLX 2160 User Manual

3.2   
System requirements
Before you begin, ensure that your system meets the following 
requirements:
Windows
ItemRequirementsRecomme
nded
Operating 
system Windows 98/Me/2000/XP/2003/Vista
CPU
Windows 98/Me/2000 Pentium II 
400 MHz or higherPentium III 
933 MHz
Windows XP/2003/ 
Vista Pentium III 
933 MHz or higherPentium IV 
1GHz
RAM
Windows 98/Me/2000 64 MB or more 128 MB
Windows XP/2003 128 MB or more 256 MB
Windows Vista 512 MB  or more 1 GB
Free disk 
space
Windows 98/Me/2000 300 MB or more 1...

4.1   
4 Network setup
(CLX-2160N only)
This chapter gives you step-by-step instructions for setting up your 
machine for network connections.
This chapter includes:
• Introduction
• Supported operating systems
• Configuring TCP/IP
• Setting ethernet speed
• Restoring the network configuration
• Printing a network configuration page
Introduction
Once you have connected your machine to a network with an RJ-45 
Ethernet cable, you can share the machine with other network users.
You need to set up the...

4.2   
6 Set the first byte between 0 and 255 using the  Scroll buttons and 
press  OK to move to the next byte.
Repeat this to complete the address from the 1st byte to the 4th 
byte.
7 When you have finished, press  OK.
8 Repeat steps 5 and 6 to configure the other TCP/IP parameters: 
subnet mask and gateway address.
9 Press the  Scroll buttons until  Static appears and press  OK.
10 Press the  Scroll buttons until  Primary DNS  appears and press 
OK .
11 Enter each byte of the address and press  OK....

5.1   
5 Selecting and loading print media
This chapter introduces you to how select and load print media for your 
machine.
This chapter includes:
• Loading originals
• Selecting print media
• Loading paper
• Setting the paper size and type
Loading originals
You can use the scanner glass to load an original for copying, scanning.
1 Lift and open the scanner lid.
2 Place the original  face down on the scanner glass and align it with 
the registration guide at the top left corner of the glass.
3 Close...

5.2   
Supported print medi a types and sizes
Ty p eSizeDimensionsWeightCapacitya
Plain paper Letter 216 x 279 mm (8.50 x 11.00 inches)
• 60 to 90 g/m
2 (16 to 24 lb 
bond)  for the paper input 
tray.
• 60 to 105 g/m
2 (16 to 28 lb 
bond) for the tray  and 
manual feeder • 1 sheet for the manual 
feeder
• 150 sheets of 75 g/m
2 
(20 lb bond) paper for the 
tray 
Legal 216 x 356 mm (8.50 x 14.00 inches)
Folio 216 x 330 mm (8.50 x 13.00 inches)
Oficio 215 x 343 mm (8.50 x 13.50 inches)
A4 210 x 297 mm...

5.3   
Media sizes supported in each mode
Guidelines for selecting and storing print media
When selecting or loading paper, envelopes, or other print materials, 
keep these guidelines in mind:
• Always use print media that conform with the specifications listed on 
page 5.5.
• Attempting to print on damp, curled, wrinkled, or torn paper can cause  paper jams and poor print quality.
• For the best print quality, use only high quality copier grade paper  specifically recommended for use in laser printers....

5.4   
Transparencies • To avoid damaging the machine, use only 
transparencies designed for use in laser 
printers.
• Transparencies used in the printer must be able  to withstand the machine’s fusing temperature. 
Check your machine’s specification to view the 
fusing temperature, see page 13.1.
• Place them on a flat surface after removing 
them from the machine.
• Do not leave them in the paper tray for long  periods of time. Dust and dirt may accumulate 
on them, resulting in spotty printing.
• To...

5.5   
Loading paper
In the tray 
Load the print media you use for the majority of your print jobs in the tray. 
The tray  can hold a maximum of 150 sheets of  75 g/m2 (20 lb bond) 
plain paper. 
Loading paper in the tray 
1 Pull the tray out of the machine.
2 Open the paper cover.
3 Adjust the size of tray until it sound click.
4 Enlarge the tray by adjusting the paper width guide.
5 Flex the paper sheets back and forth to separate pages and then 
fan them while holding one edge. Tap the edges of the...

5.6   
8 Close the paper cover.
9 Slide the tray  back into the machine.
You can load letterhead with the design side face up. The top edge 
of the sheet with the logo should be go into the machine first.
After loading paper, set the paper type and size for the tray. See 
page 5.8 for copying and faxing or the  Software Section for PC-
printing.
Note
• If there is not enough paper in the tray, load more paper.
• If you experience problems with paper feed, place one sheet  at a time in the manual...

5.7   
For paper smaller than Letter-sized, return the paper guides to their 
original positions and adjust the paper length guide and paper width 
guide.
5 Close the paper cover.
6 Slide the tray back into the machine.
Note
• Do not push the paper width guides far enough to cause the 
material to warp.
• If you do not correctly adjust the paper width guides, it may  cause a paper jams.
In the manual feeder
The manual feeder can hold special sizes and types of print material, 
such as transparencies,...