Samsung Ht C9950w User Manual

							
English 31
02 Connections
Connecting The Speakers
Press down the terminal tab on the back of the speaker. 
Insert the black wire into the black terminal (–) and the red wire \
into 
the red (+) terminal, and then release the tab.
Connect the connecting plugs to the back of the Subwoofer by 
matching the colors of the speaker plugs to the speaker jacks.
With the product turned off, insert the TX card into the TX Card 
Connection (WIRELESS) on the back of the Subwoofer.Hold the TX card so that the label "WIRELESS" faces leftward and 
insert the card into the port. 
The TX card enables communication between the product and the 
wireless receiver module. 
Connect the left and right surround speakers to the wireless receiver 
module. 
Plug the power cord of the wireless receiver module into the wall 
outlet.
Turn on the product. The product and wireless receiver module will 
communicate with each other and you will hear sound from the 
Surround speakers.1.
2.
3.
4.
•
•
5.
6.
7.
BlackRed
TX card
Subwoofer
Center SpeakerSurround Speaker (R)
Wireless Receiver Module
Front Speaker (L)
Surround Speaker (L)
This product should be connected with the SWA-5000 only.
Surround Back Speaker (L)
HT-C9950W
Front Speaker (R)
Surround Back Speaker (R)
H T-C 9950W _X AA_0820.in dd   3 1HT-C9950W_XAA_0820.indd   312010-0 8-2 0     3 :4 6:2 72010-08-20    3:46:27
 
						

							
32 English
Connections
CAUTION
Before connecting the speakers, connect the main unit to the subwoofer u\
sing the system cable. 
See page 26.
Do not let children play with or near the speakers. They could get hurt \
if a speaker falls.
When connecting the speaker wires to the speakers, make sure that the po\
larity (+/ –) is correct.
   Keep the subwoofer speaker out of reach children to prevent them from in\
serting their hands or 
alien substances into the duct (hole) of the subwoofer speaker.
   Do not hang the subwoofer on the wall through the duct (hole).
Do not insert any other TX cards. Insert only the TX card included with \
the product.
If you use a different TX card, you can damage your home theater and may\
 not be able to remove 
the card easily.
Do not insert the TX card upside down or back side fi rst.
   Insert the TX card when the product is turned off. Inserting the card wh\
en it is turned on may 
cause a problem.
  The wireless receiving antenna is built into the wireless receiver modul\
e. Keep it away from water 
and moisture.
For optimal listening performance, make sure that the area around the wi\
reless receiver module 
location is clear of any obstructions.
If you hear no sound rom the wireless surround speakers, switch the mode\
 to DVD 5.1 channel or 
Dolby Pro Logic 
II.
If you hear no sound from the surround back speakers, switch the mode to\
 7.1 channel or Dolby 
Pro Logic 
II.
In 2-CH mode, no sound eminates from the wireless surround speakers.
 NOTE
  If you place a speaker near your TV set, screen color may be distorted b\
ecause of the magnetic 
fi eld generated by the speaker. If this occurs, move the speaker away from\
 your TV set.
Place the wireless receiver module at the rear of the listening position\
. If the wireless receiver 
module is too close to the product, some sound interruption may be heard\
 due to interference.
If you use a device such as a microwave oven, wireless LAN Card, or any \
other device that uses 
the same frequency (2.4/5.8GHz) near the product, you may get some sou\
nd interruption due to 
interference.
The transmission distance from the product to the wireless receiver modu\
le is about 10m, but 
may vary depending on your operating environment. If a steel-concrete wa\
ll or metallic wall is 
between the product and the wireless receiver module, the system may not\
 operate at all, 
because the radio wave cannot penetrate metal.
If the product doesn't make wireless connection, the system needs ID Set\
ting between the 
product and wireless receiver module. With the product turned off, press\
 the remote control's 
number buttons "0" "1" "3" "5" and turn on the product. With the wireless receiver module 
turned on, press the "ID SET" button on the back of the wireless receive\
r module for 5 seconds.
!













✎





Attaching the Toroidal Ferrite Core to the Speaker Cable
Open the bigger one of two toroidal ferrite cores by 
pulling the lock lever.
Arrange all the speaker cables that are connected to 
the subwoofer and make three loops.
Attach the ferrite core as close as possible to the 
subwoofer. 
Place the toroidal ferrite core on the looped speaker 
cable as shown, and then press it closed it until you 
hear a click.1.
2.
•
3.
H T-C 9950W _X AA_0820.in dd   3 2HT-C9950W_XAA_0820.indd   322010-0 8-2 0     3 :4 6:3 12010-08-20    3:46:31
 
						

							
English 33
02 Connections
Connecting External Devices to Your TV via HDMI
HDMI is a standard digital interface for connection to such devices as a\
 TV, projector, DVD player, Blu-ray 
player, set top box and more.
HDMI removes any loss of signal from analog conversion, enabling you to \
enjoy video and audio sound 
quality as it was originally created in the digital source.
HDMI OUT : Connecting to a TV with an HDMI Cable
Connect an HDMI cable (not supplied) from the HDMI OUT jack on the bac\
k of the subwoofer to the 
HDMI IN jack on your TV.
 NOTE
Certain HDMI output resolutions may not work, depending on your TV.
If you connect or remove an HDMI cable during playback of a CD-DA, MP3 o\
r JPEG fi le, the product will stop 
playing.
After making the video connection, set the Video input source on your TV\
 to match the corresponding Video 
output (HDMI) on your product.
See your TV owner's manual for more information on how to select the TV'\
s Video Input source.
If you have set the product's remote control to operate your TV, press t\
he TV SOURCE button on the remote 
control and select HDMI as the external source of the TV.
You must have an HDMI connection to enjoy videos with 3D technology.
A long HDMI cable may cause screen noise. If this occurs, set Deep Color\
 to Off in the menu.
For a list of compatible HDMI video resolutions, see page 42.
HDMI IN : Connecting to an External Component with an HDMI Cable
Connect an HDMI cable (not supplied) from the  HDMI IN1 or HDMI IN2 jack on the back of the 
product to the HDMI OUT jack on your digital devices.
Press the FUNCTION button to select HDMI1 or HDMI2 input.
The mode switches as follows : BD/DVD   D. IN  AUX  iPod   HDMI1   HDMI2  TUNER
✎







1.
2.
DVD or Blu-ray PlayerSAT
(Satellite/Set top box)
HDMI OUT
HDMI IN
HDMI IN
Loop the HDMI cable once and attach 
the ferrite core (Large) as shown.
Attach one ferrite core (large) to the cable that is 
connected to HDMI OUT; attach the other one to the 
cable that is connected to either HDMI1 or HDMI2.
HT-C9950W_XAA_0830.indd   33HT-C9950W_XAA_0830.indd   33 2010-08-30    10:14:052010-08-30    10:14:05
 
						

							
34 English
Connections
HDMI Auto Detection Function
The product's video output automatically changes to HDMI mode when conne\
cted to a TV or other
device with an HDMI cable while the power is on.Auto Detection is not available if the HDMI cable does not support CEC.
HDMI connection description- HDMI outputs only a pure digital signal to the TV.
-  If your TV does not support HDCP, random noise appears on the screen.
What is the HDCP?
HDCP (High-band width Digital Content Protection) is a system for prot\
ecting BD/DVD content outputted via 
HDMI from being copied. It provides a secure digital link between a vide\
o source (PC, DVD. etc) and a display 
device (TV, projector. etc). Content is encrypted at the source device\
 to prevent unauthorized copies from being 
made.
CAUTION
The Anynet+ function is supported only when an HDMI Cable is connected t\
o the HDMI OUT of the 
product.
•
•
•
!

Connecting the FM Antenna
Connect the FM antenna supplied to the FM ANT Jack.
Slowly move the antenna wire around until you fi nd a location where reception is good, and then 
fasten the antenna to a wall or other rigid surface.
NOTE
This product does not receive AM broadcasts.
1.
2.
✎

FM Antenna (supplied)
HT-C9950W_XAA_0830.indd   34HT-C9950W_XAA_0830.indd   34 2010-08-30    10:14:122010-08-30    10:14:12
 
						

							
English 35
02 Connections
Connecting Audio from External Components
OPTICAL : Connecting an External Digital Component
For components with digital optical audio signals such as a Cable Box/Sa\
tellite receiver (Set-Top Box).Connect the Digital Input (OPTICAL) on the product to the Digital Audi\
o Output of the external 
digital component using a digital optical cable.
  Press the FUNCTION button to select D.IN input.
The mode switches as follows : BD/DVD   D. IN  AUX  iPod   HDMI1   HDMI2  TUNER
NOTE
To see video from your Cable Box/Satellite receiver, you must connect it\
's video output to a TV.
This system supports Digital sampling frequencies of 32 kHz of higher from external digital components.This system supports Digital sampling frequencies of 32 kHz of higher fr\
om external digital components.
This system supports only DTS and Dolby Digital audio, MPEG audio which \
is bitstream cannot be supported.
AUX : Connecting an External Analog Component
For analog audio signal components such as a VCR.
Connect AUX IN (Audio) on the product to the Audio Out of the external\
 analog component. 
Be sure to match connector colors.
 
Press the FUNCTION button to select AUX input. 
The mode switches as follows : BD/DVD   D. IN  AUX  iPod   HDMI1   HDMI2  TUNER
NOTE
  
You connect the Video Output jack of your VCR to the TV, and connect the\
 Audio Output jacks of the 
VCR to this product.
1.
2.
•
✎



1.•
2. •
✎

Optical Cable
(not supplied)
Audio Cable
 (not supplied)
If the external analog component has only one 
Audio Out, connect either left or right.
Set-Top Box AUX
White
Red
OPTICALVCR
Attach the ferrite core (Large) as close to 
AUX IN as possible with no loop of core 
made on the audio cable.
HT-C9950W_XAA_0830.indd   35HT-C9950W_XAA_0830.indd   35
2010-08-30    10:14:132010-08-30    10:14:13
 
						

							
36 English
Connections
Connecting to the Network
This product supports network based services (see pages 68~76), BD-LIV\
E, and on-line software 
upgrades through a network connection. We recommend you use an AP (Acce\
ss Point) or IP router for
the connection.
For more information on router connection, refer to the user manual of t\
he router or contact the router
manufacturer for technical assistance.
Cable Network
Using a Direct LAN Cable (UTP cable/not included), connect the LAN ter\
minal of the product to 
the LAN terminal of your modem.
Set the network options. (See page 49)
NOTE
Internet access to Samsung’s software update server may not be allowe\
d, depending on the router you use or the 
ISP’s policy. For more information, contact your ISP (Internet Servi\
ce Provider).
For DSL users, please use a router to make a network connection.
To use the AllShare function, you must connect a PC to the network as sh\
own in the fi gure above.
The connection can be wired or wireless.
1.
2.
✎




RouterBroadband modem Broadbandservice
Or
Broadband modem
(with integrated router)
Broadband service
Networking with PC forAllShare function
(See pages 75~76)
H T-C 9950W _X AA_0820.in dd   3 6HT-C9950W_XAA_0820.indd   362010-0 8-2 0     3 :4 6:3 62010-08-20    3:46:36
 
						

							
English 37
02 Connections
Wireless Network
You can connect the home thaeater to a network through a Wireless IP sha\
rer (either a router or modem).
Connect the suppplied wireless LAN adapter to the Wireless LAN Adapter j\
ack on the rear panel of 
the product.
- This unit is compatible with the supplied Wireless LAN Adapter.
Set the network options. (See page 49)
NOTE
You must use a wireless IP sharer (router or modem) that supports IEEE\
 802.11 a/b/g/n. We 
recommend using IEEE 802.11n for stable operation of the wireless networ\
k.
Wireless LAN, in its nature, may cause interference, depending on the op\
erational conditions (AP 
performance, distance, obstacle, interference by other radio devices, et\
c.).
Set the wireless IP sharer to Infrastructure mode. Ad-hoc mode is not su\
pported.
The home theater supports the following wireless security key protocols:\
Authentication Mode : WEP, WPAPSK, WPA2PSK
Encryption Type : WEP, AES
To use the AllShare function, you must connect a PC must be connected in\
 the network as 
shown in the fi gure above.
The connection can be wired or wireless.
1.
2.
✎




1)
2)


Wireless IP sharer
Wireless LAN Adapter
Networking with PC for
AllShare function
(See pages 75~76)
PC
Broadband
service
HT-C 9950W _X AA_0820.in dd   3 7HT-C9950W_XAA_0820.indd   372010-0 8-2 0     3 :4 6:3 82010-08-20    3:46:38
 
						

							
38 English
Setup
Before Starting (Initial Settings)
Turn on your TV after connecting the product.
When the product is connected to TV for the fi rst 
time, the product turns on automatically and 
displays the Initial Settings screen.
 > Move s Select
Initial Settings I On-Screen Language
Select a language for the on-screen displays.
English
Français
Deutsch
Español
Italiano
Nederlands
Press the ▲▼ buttons to select the desired 
language, and then press the  ENTER button.
Press the  ENTER button to select Start button.
     a Previous " Select
Initial Settings
TV Aspect, Musical Room Calibration and Network will be set.
Each setting may be changed later under "Settings"
Start
Press the ▲▼ buttons to select desired TV 
Aspect ratio, and then press the  ENTER button. 
(See page 41)
Musical Room Calibration  screen will be displayed.
Plug the ASC microphone into the  ASC IN jack 
on the subwoofer. (See page 45)
Press the  ENTER button to select Start button.
       d Skip
Initial Settings I Musical Room Calibration
Preparing...
Setting the Musical Room Calibration function 
takes about 3 minutes.
1.
2.
3.
4.
5.
6.
Press the ◄► buttons to select the desired 
Network Settings : Wired, Wireless, or PBC 
(WPS), and then press the  ENTER button. 
If you do not know your Network Settings, 
press the  BLUE (D) button on your remote 
instead to skip Network Settings here, fi nish 
the Initial Settings, and go to the Home menu. 
If you selected a Network Setting, go to pages 
49~52 for more information about the Network 
settings. When done, go to Step 8.
a Previous d Skip < Move " Select
Initial Settings I Network
Network Setting is needed to use various Internet services.
Choose the primary method for connecting to network.
Wired : Set the network by using Ethernet cable.
Please make sure that Ethernet cable is connected.
WiredWirelessPBC (WPS)
Press the  OK button. 
The Home menu will be displayed. (For more 
information about home menu, please see 
page 39)
Home Menu
internet radioYou Tube
No Disc a Change Device   d View Devices " Enter
Please activate Internet@TV service
to enjoy a variety of Internet Services.
 NOTE
When the product is connected to a TV for the 
fi rst time, product will turn on automatically.
This is not a malfunction.
The home menu will not be displayed if you do 
not confi gure the initial settings.
If you press the  BLUE (D) button during the 
Musical Room Calibration/Network setup, you 
can access the Home menu even if the 
network or Music Room Calibration setup is 
not complete.
When you return to Home menu, the full 
screen mode will be canceled automatically.
7.
8.
•
✎




H T-C 9950W _X AA_0820.in dd   3 8HT-C9950W_XAA_0820.indd   382010-0 8-2 0     3 :4 6:3 92010-08-20    3:46:39
  
						

							
English 39
03 Setup
If you want to display Initial Settings screen 
again in order to make changes, press the 
STOP ( ) button on the front panel of the 
product for more than 5 seconds with no disc 
inserted.
Use the HDMI cable to connect the product to 
an  Anynet+ (HDMI-CEC) -compliant Samsung TV.
If the TV uses a language supported by the 
product, that language will be set to a 
preferred language automatically.
However, the  Anynet+ (HDMI-CEC)  feature 
should be set to  On in both the TV and the 
product.
If you leave the product in the Stop mode for 
more than 5 minutes without operating it, a 
screen saver appears on your TV. If you leave 
the product in the screen saver mode for 
more than 25 minutes, the power 
automatically turns off except during playback 
of a CD-DA (Automatic Power-Off Function).
Navigating the Menu
MENU
TOOLS INFO
RETURN
TUNER MEMORY MO/ST
EXIT
DISC
MENU TITLE MENU
POPUP
TOOLSINFO
TUNER MEMORYMO/ST
DISCMENUTITLE MENUPOPUP1
2 4
3
1MENU Button : Press this to move to the home menu.
2RETURN  Button : Return to the previous menu.
3
ENTER / DIRECTION  Button:
Press the arrow buttons to move the cursor and select 
an item.
Press the  ENTER button to launch the selected item or 
confi rm the setting.
4EXIT  Button : Press this to exit the menu.
Press the  POWER button.
The Home Menu will appear.



1.
Set the remote to the Home Theater mode 
by pressing the  BD RECEIVER/TV  button on 
the top of the remote until the LED above the 
button turns orange.
NOTE 
To control the Home Theater, the remote must 
be in Home Theater mode.
Home Menu
internet radioYou Tube
No Disc a Change Device   d View Devices " Enter
Please activate Internet@TV service
to enjoy a variety of Internet Services.
1
2
4
3
5
6
1Selects the Internet@TV.
2Selects the Videos.
3Selects the Music.
4Selects the Photos.
5Selects the Settings.
6Displays buttons available.
3.  Press the ◄► buttons to select  Settings, 
and then press the  ENTER button.
4.  Press the ▲▼ buttons to select the desired 
submenu, and then press the  ENTER 
button.
5.  Press the ▲▼ buttons to select the desired 
item, and then press the  ENTER button.
6.  Press the  EXIT button to exit the menu.
NOTE 
When the product is connected to the network, 
select Internet@TV from the Home menu. 
Download desired content from  Samsung AppS.
The access steps may differ depending on the 
menu you select.
The OSD (On Screen Display) may change in 
this product after you upgrade the software 
version.
2.
✎

•
✎



H T-C 9950W _X AA_0820.in dd   3 9HT-C9950W_XAA_0820.indd   392010-0 8-2 0     3 :4 6:4 52010-08-20    3:46:45
 
						

							
40 English
Setup
Display
You can confi gure various display options such 
as the TV Aspect Ratio, Resolution, 3D, etc.
3D
Select whether to play a Blu-ray Disc with 3D 
contents in 3D Mode.
DisplayAudio
System
Network
Language
Security
General
Support
Settings 
3D
Still Mode  : Auto
3D Mode  : Auto
TV Screen Size :      55    inch
 > Move s Select  r Return
3D
3D Mode
Auto : The 3D Blu-ray Disc is played in the 3D 
mode if your product detects a TV which 
supports 3D. It is played in 2D mode if your 
product detects a TV which cannot support 
3D.
3D  : The 3D Blu-ray Disc is played in 3D mode 
at all times. If a TV cannot support 3D Blu-ray 
discs, the TV's screen can be black.
2D  : The 3D Blu-ray Disc is played in 2D mode 
at all times. Choose this to view a picture 
without 3D effects or when a TV cannot 
support 3D Blu-ray discs.
NOTE
If you press the  STOP ( ) button once during 
3D disc playback, the 3D mode option will be 
deactivated.
To activate the 3D mode option during 3D disc 
playback, press the  STOP 
( ) button twice.
Depending on the content and the position of 
the picture on your TV screen, you may see 
vertical black bars on the left or right or both 
sides of the screen.
•
•
•
✎


TV Screen Size
Lets you enter the actual screen size of your 
TV so that the product can adjust the image 
according to the screen size and display an 
optimal 3D image. (The maximum allowed 
screen size is 116 inches for this product.)
CAUTION
To enjoy the 3D effect, connect a 3D device 
(3D compliant AV receiver or TV) to the 
product and wear 3D glasses while playing 
the 3D content.
The home theater outputs 3D signals only 
through HDMI cable attached to HDMI OUT.
As the video resolution in 3D play mode is 
fi xed according to the resolution of the 
original 3D video, you can not change the 
resolution to your preference.
Some functions such as BD Wise, screen 
size adjustment, and resolution adjustment 
may not operate properly in 3D play mode.
You must use a high-speed HDMI cable for 
a proper output of the 3D signal.
Stay at least three times the width of the 
screen  from the TV when watching 3D 
images. For example, if you have a 46 inch 
screen, stay 138 inches  (11.5 feet) from the 
screen.
-   Place the 3D video screen at eye level for 
the best 3D picture.
When the product is connected to some 3D 
devices, the 3D effect may not function 
properly.
This product does not convert 2D content to 
3D.
!








H T-C 9950W _X AA_0820.in dd   4 0HT-C9950W_XAA_0820.indd   402010-0 8-2 0     3 :4 6:4 62010-08-20    3:46:46