Samsung Ht Db1350 Instruction Manual

							50
To listen in the auto sound calibration mode, briefly press ASC button.
(If you set the auto sound calibration in the order from 1 to 4 above for the first time)
•The selection alternates between ASC ONand ASC OFFin the display.
•If you select ASC ON, you can listen in the auto sound calibration mode. 
If you select ASC OFF, you can listen in the mode set in the audio setting of the setup screen.
1
Plug the auto sound calibration
microphone into the auto sound
calibration input jack.
2
Place the auto sound calibration
microphone at the listeners position.
4
5
Press ASC button.
When the message REMOVE MIC
appears in the display, unplug the auto
sound calibration microphone.
A bell will sound and
the setup finishes.
•The tone will be output twice, in the given order (L ➝ C ➝ R ➝ RS  ➝
LS ➝ SW), and 5.1-channel sound field is optimized automatically.
•The auto sound calibration setup takes about 2 minutes to complete.
3
Adjust the volume control on the main
unit as follows:
•If the distance between the listener and the speaker is over 5 m:
Set the main units volume to over 25.
•If the distance between the listener and the speaker is 3 to 5 m:
Set the main units volume to 25.
•If the distance between the listener and the speaker is below 3 m:
Set the main units volume to 15.
To cancel the auto sound calibration setup, press ASC button.
•The tone output stops, CANCEL ASC appears in the display followed by REMOVE MIC, and the setup will be cancelled.
A tone is output.A result for each speaker is displayed.
SETUP
 31P~68P(DB1350)-GB  2/16/04 5:49 PM  Page 55
 
						

							51
DSPCMXLINEAR PCM
MPEG-2 AACMPEGLCRSWLSRSTITLEPBC CHAP PRGM RDS RT TATUNEDkHzMHzST
DSPCMXLINEAR PCM
MPEG-2 AACMPEGLCRSWLSRSRTTATUNEDkHzMHzST
DSPCMXLINEAR PCM
MPEG-2 AACMPEGLCRSWLSRSTITLE PBCCHAPPRGM RDS RTTATUNEDkHzMHzST
DSPCMXLINEAR PCM
MPEG-2 AACMPEGLCRSWLSRSTITLE PBCCHAPPRGM RDS RTTATUNEDkHzMHzST
DSPCMXLINEAR PCM
MPEG-2 AACMPEGLCRSWLSRSTITLE PBCCHAPPRGM RDS RTTATUNEDkHzMHzST
DSPCMXLINEAR PCM
MPEG-2 AACMPEGLCRSWLSRSTITLE PBCCHAPPRGM RDS RTTATUNEDkHzMHzST
DSPCMXLINEAR PCM
MPEG-2 AACMPEGLCRSWLSRSTITLE PBCCHAPPRGM RDS RTTATUNEDkHzMHzST
DSPCMXLINEAR PCM
MPEG-2 AACMPEGLCRSWLSRSTITLEPBC CHAP PRGM TATUNEDkHzMHzST
DSPCMXLINEAR PCM
MPEG-2 AACMPEGLCRSWLSRSTITLEPBC CHAP PRGM RDS RT TATUNEDkHzMHzST
DSPCMXLINEAR PCM
MPEG-2 AACMPEGLCRSWLSRSTITLEPBC CHAP PRGM RDS RT TATUNEDkHzMHzST
CMXLINEAR PCM
MPEG-2 AACMPEGLCRSWLSRSTITLE PBCCHAPPRGM RDS RTTATUNEDkHzMHzST
Live Surround Mode
You can reproduce a 2-channel sound source, such
as VCD, CD, and radio broadcast, in 5.1-channel
surround sound.
Super 5.1 Function
•Each time the button is pressed, the
selection alternates between SUPER
5.1 and SUPER OFF.
•Select SUPER 5.1 to play 2-channel
sound in 5.1 channel.
Press SUPER5.1
button.
DSPCMXLINEAR PCM
MPEG-2 AACMPEGLCRSWLSRSTITLEPBC CHAP PRGM RDS RT TATUNEDkHzMHzST
DSPCMXLINEAR PCM
MPEG-2 AACMPEGLCRSWLSRSTITLE PBCCHAPPRGM RDS RTTATUNEDkHzMHzST
If you select Music Sound Field when listening to a
2-channel sound source, it will be reproduced in
5.1-channel surround sound so that you can enjoy a
dynamic sound with a sense of presence.
Live Surround Mode Function
•Each time the button is pressed,
the selection changes as follows:
Press MUSICbutton.
You select from 3 different modes of sound field
for movies.
Movie Sound Field Function
•Each time the button is pressed,
the selection changes as follows:
When watching
an action movie
When watching a
drama
When watching a
musical
Press MOVIE
button.
•When you insert a DVD recorded in 2-channel or multi-channel format and press the
SUPER 5.1 button, the message THIS FUNCTION APPLIES ONLY 2CH SOURCE
appears in the display and it will not work.Note
 31P~68P(DB1350)-GB  2/16/04 5:49 PM  Page 56
 
						

							52
Virtual Headphone Function
Use headphones (not supplied) for private listening pleasure.
You can enjoy a dynamic sound effects similar to that of 5.1 channel
surround sound using a conventional stereo headphone.
ASC LSM V-H/P
•To purchase headphones, please
contact the nearest Samsung
Electronics Customer Center.
12
•Each time the button is pressed, the
selection alternates between
VIRTUAL ONand VIRTUAL OFF.
Plug the
headphones into the
headphone jack.Press V-H/P
button.
•VIRTUAL ON:Select to enjoy a 5.1-channel surround sound that gives the
feeling of being in a baseball park or concert hall.
•VIRTUAL OFF:Select to listen to a standard 2-channel stereo sound.
SETUP
•Do not listen at extremely high volume levels when using headphones.
Extended, high-volume listening can lead to permanent hearing loss.Note
 31P~68P(DB1350)-GB  2/16/04 5:49 PM  Page 57
 
						

							53
Dolby Pro Logic II Mode
You can select the desired Dolby Pro Logic II audio mode.
Press       PL II MODEbutton.
DSPCMXLINEAR PCM
MPEG-2 AACMPEGLCRSWLSRS
TITLE PBCCHAPPRGM RDS RTTATUNEDkHzMHzST
DSPCMXLINEAR PCM
MPEG-2 AACMPEGLCRSWLSRS
TITLE PBCCHAPPRGM RDS RTTATUNEDkHzMHzST
DSPCMXLINEAR PCM
MPEG-2 AACMPEGLCRSWLSRS
TITLE PBCCHAPPRGM RDS RTTATUNEDkHzMHzST
DSPCMXLINEAR PCM
MPEG-2 AACMPEGLCRSWLSRS
TITLE PBCCHAPPRGM RDS RTTATUNEDkHzMHzST
DSPCMXLINEAR PCM
MPEG-2 AACMPEGLCRSWLSRS
TITLE PBCCHAPPRGM RDS RTTATUNEDkHzMHzST
DSPCMXLINEAR PCM
MPEG-2 AACMPEGLCRSWLSRS
TITLE PBCCHAPPRGM RDS RTTATUNEDkHzMHzST
S
PRO LOGIC II
•MUSIC: When listening to music, you can experience sound effects as if you are listening to the actual performance.
•CINEMA: Adds realism to the movie soundtrack.
•PRO LOGIC: You will experience a realistic multi-channel effect, as if using five speakers, while using just the front left
and right speakers.
•MATRIX: You will hear 5.1 channel surround sound.
STEREO: Select this to listen to sounds from the front left and right speakers and the subwoofer only.
•Each time the button is pressed, the mode changes as follows.
•When selecting Pro Logic II mode, connect your external device to the
AUDIO INPUT jacks (L and R) on the player. If you connect to only one of
the inputs (L or R), you cannot listen to 5.1 channel surround sound.Note
 31P~68P(DB1350)-GB  2/16/04 5:49 PM  Page 58
 
						

							54
Dolby Pro Logic II Effect
This function works only in Dolby Pro Logic MUSIC mode.
12
•You can select between 0 and 7.•You can select between 0 and 6.
34
•PANORAMA: This mode extends the front stereo image to include the surround speakers for
an exciting wraparound effect with side wall imaging.
•CENTER WIDTH: Sound is output to the center speaker only. The front left and right speakers
produce phantom sound. 
•DIMENSION: Incrementally adjusts the sound field (DSP) from the front or rear.
•When playing a DVD disc encoded with two or more channels, multi-channel mode will be
selected automatically and                 (Dolby Pro Logic II) button does not work.
•You can select either 0 or 1.
Press        PL II MODE
button to select ‘MUSIC’
mode.Press PL II EFFECT button
and then press Cursor      ,
buttons to select the mode.
DSP
CMX
LINEAR PCM
MPEG-2 AACMPEGLCRSWLSRS
TITLE PBCCHAPPRGM RDS RTTATUNED
kHzMHz
STDSP
CMX
LINEAR PCM
MPEG-2 AACMPEGLCRSWLSRS
TITLE PBCCHAPPRGM RDS RTTATUNED
kHzMHz
ST
DSP
CMX
LINEAR PCM
MPEG-2 AACMPEGLCRSWLSRS
TITLE PBCCHAPPRGM RDS RTTATUNED
kHz
MHz
STDSP
CMX
LINEAR PCM
MPEG-2 AACMPEGLCRSWLSRS
TITLE PBCCHAPPRGM RDS RTTATUNED
kHz
MHz
ST
Press PL II EFFECT button
and then press Cursor      ,
buttons to select the mode.
Press PL II EFFECT button
and then press Cursor      ,
buttons to select the mode.
Note
SETUP
 31P~68P(DB1350)-GB  2/16/04 5:49 PM  Page 59
 
						

							55
Listening to Radio
You can listen to the chosen band (FM, MW, LW broadcast stations) by using
either the automatic or manual tuning operation.
21
• The selection toggles back
and forth between FM
➝ MW
➝ LW each time the
TUNER(BAND)button is
pressed.
Tune in to the
desired station.Press TUNER/
BANDbutton.
Automatic Tuning 2
Manual Tuning
21
Select a broadcast
station.
Press the STOP(   )
button to select
PRESET and then press
button to select the preset station.Automatic Tuning 1
Press the Function
button to select the
desired band (FM,
MW, LW).
Press the STOP(   ) button
to select MANUAL and
then press and hold                   button to
automatically search the band.Automatic Tuning 2
Press STOP(   ) to select
MANUAL and then briefly
press to tune in to a lower or
higher frequency.Manual Tuning
•Each time the button is pressed, the sound switches between STEREO and MONO.
•In a poor reception area, select MONO for a clear, interference-free broadcast.
Press MO/STbutton to listen in Mono/Stereo. 
(This applies only when listening to an FM station.)
When                is pressed, a
preset broadcast station is
selected.
Press and hold                 to
automatically search for
active broadcasting stations.
Briefly press                 to
increase or decrease the
frequency incrementally.Automatic Tuning 1
Remote Control Unit
Main Unit
 31P~68P(DB1350)-GB  2/16/04 5:49 PM  Page 60
 
						

							56
Presetting Stations
To tune in to a preset station, press                on the 
remote control to select a channel.
•Refer to Step 2 on page 55 to
automatically or manually tune in
to a station.
21
•Each time the button is pressed,
the band switches between 
FM
➝ MW ➝ LW.
TITLECHAPPRGM RDS RTSTTUNED
kHzMHz
TITLECHAPPRGM RDS RTSTTUNED
kHzMHz
TITLERDS RTSTTUNED
kHzMHz
•“PRGM” flashes in the display. 
3
Example: Presetting FM 89.1 in the memory 
Press             to
select 89.10. Press the
TUNER(BAND)
button  and select
•Press the TUNER MEMORYbutton before
‘
PRGM’ disappears from the display.
•‘PRGM’ disappears from the display and
the station is stored in memory.
54
•You can select between 1 and
15.
TITLERDS RTSTTUNED
kHzMHz
TITLECHAPRDS RTSTTUNED
kHzMHz
Press the TUNER
MEMORY button.
Press the TUNER
MEMORY button.
6
To preset another
station, repeat
steps 2 to 5. Press                 to
select preset
number.
RADIO OPERATION
You can store up to:
15 FM stations
8 MW stations          
7 LW stations• FMFrequency Modulation
• AM(MW)Medium Wave
• LWLong Wave
 31P~68P(DB1350)-GB  2/16/04 5:49 PM  Page 61
 
						

							About RDS broadcasting
• RDS is not available for MW/LW broadcasts.
• RDS may not operate correctly if the station tuned is not transmitting
RDS signal properly or if the signal strength is weak.
• If searching finishes at once,“PS”,and “RT” will not appear on the display.
Using the RDS (Radio Data System) to receive FM stations
What information can RDS signals provide?
RDS allows FM stations to send an additional signal along with their regular program signals. For
example,the stations send their station names,as well as information about what  type of program they
broadcast, such as sports or music,etc.
When tuned to an FM station which provides the RDS service,the RDS indicator
lights up on the display.
• Description on RDS function
1. PTY (Program Type) : Displays the type of programme currently being broadcast
2. PS NAME (Program Service Name) :
Indicates the name of broadcasting station
and is composed of 8 characters.
3. RT (Radio Text) :Decodes the text broadcast by a station (if any) and is composed
of maximum 64 characters.
4. CT (Clock Time) :Decodes the real time clock from the FM frequency.• Some stations may not transmit PTY, RT or CT information therefore this may not be
displayed in all cases.
5. TA (Traffic Announcement) :
When this symbol flashes it shows that the traffic
announcement is in progress.
Note
Note
You can see the RDS signals the station sends on the display.
TO show the RDS signals
Press RDS DISPLAY while listening to an FM ststion.
Each time you press the button, the display change to show you the following information:
PS (Program Service) :While searching,PSappears and then the station names will be
displayed.NO PS appears if no signal is sent.
RT(RadioText) : while searching,RTappears and then text messages the station sends
will be displayed. NO RTappears if no signal is sent.
Frequency : station frequency (non-RDS service)
About characters shown in the display
When the display shows PS,or RT signals,the following haracters are used.
• The display window cannot differentiate upper case and lower case lrtters and always
uses upper case letters.
• The display window  cannot show accented letters, “A,” for instance, may stans for
accented “A’s” like “À, Â, Ä, Á, Åand Ã.”
57
 31P~68P(DB1350)-GB  2/16/04 5:49 PM  Page 62
 
						

							PTY (Program Type) indication and PTY-SEARCH function
58
To search for a program using the PTY codes
Before you start, remember...
• The PTY Search is only applicable to preset
stations.
• To stop searching any time during the process,
press PTY SEARCH while searching.
• There is a time limit in doing the following steps. 
If the setting is cancelled before you finish, start
from step 1 again.
• When pressing the buttons on the primary remote
control, make sure that you have selected the FM
station using the primary remote control. One  of the advantages of the RDS service is that you can locate a particular kind of program from the
preset channels by specifying the PTY codes.
Press PTY SEARCH while listenning to an
FM station.
1
Press the PTY-or PTY+until the PTY code
you want appears on the display.
• The display gives you the PTY codes described
to the right.
2
Press PTY SEARCH again, while the PTY
code selected in the previous step is still on
the display.
• The center unit searches 15 preset FM
stations,stops when it finds the one you
have selected, and tunes in that station.
3
Display
NEWS
AFFAIRS
INFO
SPORT
EDUCATE
DRAMA
CULTURE
SCIENCE
VARIED
POP M
ROCK M
M.O.R.M
LIGHT M
CLASSIC
OTHER M
WEATHER
FINANCE
CHILDREN
SOCIAL A
RELIGION
PHONE IN
TRAVEL
LEISURE
JAZZ
COUNTRY
NATION M
OLDIES
FOLK M
DOCUMENTProgram Type
• News including an announced opinion and
report
• Several matters including a current incident,
documentary, discussion and analysis.
•  Information including weights and measures,
returns and forecast, matters interesting the
customer, medical information, etc.
• Sports
• Education
• Drama-Radio serial, etc.
• Culture-National or local culture including the
religious problem, social science, language,
theater,etc.
• Natural science and technology
• Others-Speech, amusing program (quiz,
game), interview, comedy and satirical play,
etc.
• Pop music
• Rock music
• Current contemporary music considered to be
“easylistening.”
• Light classical music- Classical music and
instrumental and chorus music
• Heavy classical  music-Orchestra music,
symphony, chamber music and opera
• Other music - Jazz, R&B country music
• Weather
• Finance
• Children’s programmes
• Social affairs
• Religion
• Phone in
• Travel
• Leisure
• Jazz Music
• Country Music
• National Music
• Oldies Music
• Folk Music
• Documentary
RADIO OPERATION
 31P~68P(DB1350)-GB  2/16/04 5:49 PM  Page 63
 
						

							59
Convenient Functions
•The remaining time before the DVD player will shut itself off is displayed.
•Pressing the button again changes the sleep time from what you have set earlier.
To confirm the sleep timer setting, press SLEEPbutton.
• SLEEP will be displayed. Each time the button is pressed
the preset time changes as follows: 10 ➝ 20 ➝ 30 ➝ 60 ➝
90 ➝ 120 ➝ 150 ➝ OFF.
TITLECHAPPRGM RDS RTSTTUNED
kHzMHz
Press SLEEPbutton.
Sleep Timer Function
You can set the time that the DVD player will shut itself off.
To cancel the sleep timer, press SLEEPbutton until
OFF appears on the display.
 31P~68P(DB1350)-GB  2/16/04 5:49 PM  Page 64