Samsung Rsj1keps User Manual

							
setting up _11

setting up your side-by-side 
refrigerator
Removing the freezer door
A few things to mention first.
•	Make sure that you lift the door straight up so the hinges are not bent \
or broken.
•	Be careful not to pinch the water tubing and wire harness on the door.
•	Place doors on a protected surface to prevent scratching or damage.
1.	With the Freezer door closed, remove the upper hinge cover 1 using a screwdriver, and 
then disconnect the wires by gently pulling them apart .
.	Remove hinge screws  and the ground screw  by turning counter-clockwise, and take 
off the upper hinge . Be careful that the door does not fall on you as you are removing it
.	Next, remove the door from the lower hinge  by carefully lifting the door straight up .
.	Remove the lower hinge  using a hex wrench.






1
01 sEtting uP

DA68-01651A(JM)-EN(0.4).indd   112007.5.25   3:18:11 PM
   
						

							
1_ setting up

Removing the Fridge Door
1.	With the door closed, remove the upper hinge cover 1 using a screwdriver.
.	Remove hinge screws  and the ground screw  by turning counter-clockwise, and take 
off the upper hinge . Be careful that the door does not fall on you as you are removing it.
.	Remove the door from the lower hinge  by lifting the door straight up .
.	Remove the lower hinge  from the bracket in  by gently lifting the lower hinge upwards.
1




DA68-01651A(JM)-EN(0.4).indd   122007.5.25   3:18:12 PM
  
						

							
setting up _1

setting up your side-by-side 
refrigerator
rEattaChing thE rEfrigErator Doors
Once you have safely placed your refrigerator where you plan for it to s\
tay, it is time to put the doors back on.
Reattaching the Freezer Door
1.	Insert the lower hinge 1 back into 
						the lower hinge bracket .
.	Replace the freezer door by inserting the hose  back into the lower corner of the door 
and then into the hole on the lower hinge . Gently pull the hose back down so that it runs 
straight, with no kinks or bends.
.	Insert the upper hinge shaft  into the hole on the corner 
of the freezer door . Make sure the hinge is level between 
the upper hinge hole  and the  hole of the cabinet  and 
reattach the hinge screws  and ground screw 10 by turning 
in a clockwise direction.
.	Reconnect the wires.
.	Place the front edge of the upper hinge cover  
11 on the front of the upper hinge 1 and 
reattach with the screw.
1


01 sEtting uP
1
11

DA68-01651A(JM)-EN(0.4).indd   132007.5.25   3:18:13 PM
  
						

							
1_ setting up

Reattaching the Fridge Door
1.	Insert the lower hinge 1 back 
into the lower hinge bracket .
.	Fit the hole in the corner of the fridge door  over         the 
lower hinge .
.	Insert the upper hinge shaft  into the hole on the hinge 
. Make sure the hinge is level between the upper hinge 
hole  and the hole on the top of the cabinet . Then, 
reattach hinge screws  and the ground screw 10 by 
turning it in a clock wise direction.
.	Place the front part of the upper hinge cover  
11 on the front of the upper hinge 1 and 
reattach it with the screw.
1



1
11

DA68-01651A(JM)-EN(0.4).indd   142007.5.25   3:18:14 PM
  
						

							
setting up _1

setting up your side-by-side 
refrigerator
Reattaching the Water Supply Line
1.	Insert the water line 1 into the coupler .
.	Then, tighten the screw on the hose clamp .
Reattaching the Front Leg Cover
Before attaching the cover, check water connector for leakage. 
Replace the front leg cover by turning the three screws clockwise, as sh\
own in the figure.
front Leg Cover
screw

1
01 sEtting uP

DA68-01651A(JM)-EN(0.4).indd   152007.5.25   3:18:17 PM
        
						

							
1_ setting up

LEVELing thE rEfrigErator
Now that the doors are back on the refrigerator, you will want to make s\
ure the refrigerator is level so 
you can then make final adjustments. If the refrigerator is not level,\
 it will not be possible to get the doors 
perfectly even.
The front of the refrigerator is also adjustable.
When the Freezer door is lower than the fridge
Insert a flat-blade screwdriver into a notch on the Leg, turn it clock\
wise or counter clockwise to 
level the freezer.
When the Freezer door is higher than the fridge
Insert a flat-blade screwdriver into a notch on the Leg, turn it clock\
wise or counter clockwise to 
level the fridge.
Refer to the next section for the best way to make very minor adjustment\
s to the doors.
Leg
screw Driver
Leg
screw Driver

DA68-01651A(JM)-EN(0.4).indd   162007.5.25   3:18:17 PM
   
						

							
setting up _1

setting up your side-by-side 
refrigerator
MaKing Minor aDJustMEnts to thE Doors
Remember, a leveling refrigerator is necessary for getting the doors per\
fectly even. If you need help, 
review the previous section on leveling the refrigerator.
When	the	door	of	the	freezer	is	lower	
than	the	fridge
When	the	door	of	the	freezer	is	higher	
than	the	fridge
In both cases the process to correct the imbalance is the same. Open the\
 doors and adjust 
them, one at a time, as follows:
1.	Unscrew the nut 1 from the lower hinge until it reaches the upper end of the bolt .
When you release the nut 1, make sure that you use the Allen wrench provided  to 
loosen the bolt  in a counter-clockwise direction. You should then be able to unscrew th\
e 
nut 1 with your fingers.
.	Adjust the height difference between the doors by turning the bolt  clockwise  or 
counter clockwise .
When you turn clockwise , the door will move up.
adjustment partadjustment part


1
Wrench
bolt
Nut


Wrench
bolt
01 sEtting uP

DA68-01651A(JM)-EN(0.4).indd   172007.5.25   3:18:18 PM
   
						

							
1_ setting up

.	After adjusting the doors, turn the nut 1 clockwise  until it reaches the lower end of 
the bolt, then tighten the bolt again with the wrench  to fix the nut in place 1.
If you do not secure the nut firmly, the bolt may release.
ChECKing thE watEr DisPEnsEr LinE (oPtionaL)
A water dispenser is just one of the helpful features on your new Samsun\
g refrigerator. To help promote 
better health, the Samsung water filter removes unwanted particles fro\
m your water. However, it does not 
sterilize or destroy microorganisms. You will need to purchase a water p\
urifying system to do that.
In order for the icemaker to operate properly, water pressure of 138 ~862 Kpa is required. Under normal 
conditions, a 170 cc paper cup can be filled in 10 seconds.
If the refrigerator is installed in an area with low water pressure (be\
low 138 Kpa), you can install a booster 
pump to compensate for the low pressure.
Make sure the water storage tank inside the refrigerator is properly fi\
lled. To do this, press the water 
dispenser lever until the water runs from the water outlet.
Water Line installation Kits are included with unit. You can find it i\
n freezer drawer.
Parts for water line Installation
Connecting to the water supply line
1.	first,	shut	off	the	main	water	supply	line.
.	locate	the	nearest	cold,	drinking	water	line.
.	follow	the	Water	line	Installation	Instructions	
				in	the	installation	kit.
.	After	connecting	the	water	supply	to	the	water	filter,	turn	your	main	water	supply	
back	on	and	dispense	about	1l	to	clear	and	prime	the	water	filter.


1
Wrench
bolt
Nut
Close	MainWater	pipe
Close	MainWater	pipeNo	gap
	1		Water	line	fixer								and	screws		Pipe								connector			Water	line			protection	tube			Water	line			Water	filter
CAUTION
The water line must be connected
to the cold water pipe.If it is connected to the hotwater pipe, it may cause thepurifier to malfunction.

DA68-01651A(JM)-EN(0.4).indd   182007.5.25   3:18:20 PM
   
						

							
setting up _1

setting up your side-by-side 
refrigerator
instaLLing thE watEr DisPEnsEr LinE
Connecting the water line to the refrigerator
1.    Remove the cap from water line on the unit and insert compression nut to\
 the water line on 
the unit after disassembling from provided water line.
2. Connect both water line from the unit and water line provided kit.
3.  Tighten the compression nut onto the compression fitting. Be careful n\
o gap between two 
items.
4. Turn water on and check for any leakage.
Only connect the water line to a drinkable water source. 
If you have to repair or disassemble the water line, cut off 6.5mm of th\
e plastic tubing to 
make sure you get a snug, leak-free connection.
Before being used, the leakage in these places should be examined
• Samsung Warranty does 
not cover  WATER LINE 
INSTALLATION.
• It’ll be done at customer’s 
charge except the retail price 
includes installation cost.
• Please contact Plumber or 
Authorized Installer for the installation if needed.
• If Water leakage happened due to improper installation, Please cont\
act installer.
Installing the water filter.
1.	Remove the water filter from the box and put 
a replacement indicator sticker on the filter as 
shown.
.	Place a sticker on the filter that dates six months 
in the future. For example, if you install the water 
filter in March, put the “SEP” sticker on the filter 
to remind you to replace in September. That 
way you’ll know when it is time to replace the 
filter. Normally filter life is about 6 months.
.	Next, remove the fixed cap by turning it counter 
clockwise. Keep the cap in a safe place for use 
if you choose not to use a filter.
sticker
(Month indication)


1
01 sEtting uP
Remove	cap
Water	linefrom	unit
Water	linefrom	Kit
No	gap
loosen	a
CAUTION

DA68-01651A(JM)-EN(0.4).indd   192007.5.25   3:18:22 PM
 
						

							
0_ setting up

.	Remove the filter’s protective cap 
and then position and insert the 
filter into the filter housing.
.	Slowly turn the water filter 
clockwise 90º to align with the 
indication mark on the cover, 
locking the filter in position. Make 
sure that the indicator is lined up 
with the “lock” position. Remember, 
do not over-tighten.
If your model contains wine shelf, you should remove the wine shelf befo\
re installing water 
filters.
Removing any residual matter inside the water supply line after 
installing filter.
1.	Turn ON the main water supply & turn OFF the valve to the 
water supply line.
.	Run water through the dispenser until the water runs clear 
(approx. 1L). This will clean the water supply system and 
remove air from the lines.
.	Additional flushing may be required in some households.
.	Open the refrigerator door and make sure there are no 
water leaks coming from the water filter.
A newly installed water filter cartridge may cause water 
to briefly spurt from the water dispenser. This is due to 
air getting into the line. It should pose no problem to 
operation.
Check the amount of water supplied to the ice tray. (Optional)
1.	Lift up the icemaker bucket and gently pull out of the freezer.
.	When you press the Test button, the ice cube container is filled with water from the water 
supply tap. Check to make sure the amount of water is correct(see the i\
llustration below).
If the water level is too low, the ice cubes will be small. This is a wa\
ter pressure problem from 
with in the main water pipes, not the refrigerator.
ice maker
1
feeler arm
test button
Check the water level
Cover filter
align the indicationmark with lock position
separationof red cap
waterice

DA68-01651A(JM)-EN(0.4).indd   202007.5.25   3:18:24 PM