Samsung Sp H710ae User Manual

							Connecting to PCConnecting to PC
61
CAUTION
DVI-D cable does not support
analog RGB signals.
PC Video Cable
(15-pin signal)DVI-D
(supports only digital signals)
This appliance supports VESA Plug & Playand
recognizes connection to PC automatically.
VESA Plug & Play
Pin Configuration of PC Video Port Plug
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15Red (R)
Green (G)
Blue (B)
Ground 
Ground  (DDC)
Red (R) Ground
Green (G) Ground
Blue (B) Ground
Reserved
Ground Sync
Ground
Data (DDC)
Horizontal Sync
Vertical Sync
Clock (DDC)
Pin No. PC Input
1
2
3
4
5
6
7
8
9
10
11
12T.M.D.S. DATA2-
T.M.D.S. DATA2+
T.M.D.S. DATA2/4 Shield
T.M.D.S. DATA4
-
T.M.D.S. DATA4+
Clock (DDC)
Data (DDC)
No Connection
T.M.D.S. DATA1
-
T.M.D.S. DATA1+
T.M.D.S. DATA1/3 Shield
T.M.D.S. DATA3
-
Pin No. Signal
13
14
15
16
17
18
19
20
21
22
23
24T.M.D.S. DATA3+
+5V Power
Ground for 5V
Hot Plug Detect
T.M.D.S. DATA0
-
T.M.D.S. DATA0+
T.M.D.S. DATA0/5 Shield
T.M.D.S. DATA5
-
T.M.D.S. DATA5+
T.M.D.S. Clock Shield
T.M.D.S. Clock+
T.M.D.S. Clock
-
Pin No. Signal
Downloaded From projector-manual.com Samsung Manuals 
						

							Automatic Picture Adjustment
Used to adjust frequency and phase of PC screen automatically.
Connecting to PC
Automatic Picture Adjustment
62
Before adjusting!
Set the input mode to PC.
1
MENU
2, 3, 4
Select
2, 3
…/†
5
EXIT
PC
Press the MENUbutton.
The main menu is displayed.1
Press the or button to move to Setup.
The Setupmenu is displayed.
Press the  button.
2
Press the or button to move to PC, then
press the  button.
The Auto Adjustmentis selected.3
Press the EXITbutton to exit the menu.5
Press the  button.
Auto Adjustment in progress message is displayed and PC
screen is adjusted automatically.4
Auto Adjustment in Progress..
Please Wait
Setup
Install : Front-Floor √
Light Setting : Theater√
V-Keystone√
Test Pattern √
PC√
Factory Default√
Information√
Move
Enter Return
PC
Auto Adjustment√
Coarse 1344
Fine 0
Zoom√
Reset√
Move
Enter Return
Downloaded From projector-manual.com Samsung Manuals 
						

							Connecting to PC
Frequency Adjustment 
63
1
MENU
2, 3, 4
Select
2, 3, 4
…/†/œ/√
5
EXIT
Frequency Adjustment 
Used to adjust frequency when vertical lines appear on PC screen.
Before adjusting!
Set the input mode to PC.
PC
Press the MENUbutton.
The main menu is displayed.1
Press the or button to move to Setup.
The Setupmenu is displayed.
Press the  button.
2
Press the or button to move to PC, then
press the  button.
The PCmenu is displayed.3
Press the EXITbutton to exit the menu.5
Press the or button to move to Coarse, then
press the  button.
Press the œor √button to adjust.
4
PC
Auto Adjustment√
Coarse 1344
Fine 0
Zoom√
Reset√
Move
Enter Return
1344 …
Coarse
†
Downloaded From projector-manual.com Samsung Manuals 
						

							Fine Tuning with the Phase Adjustment
Used to fine tune the PC screen.
Connecting to PC
Fine Tuning with the Phase Adjustment
64
1
MENU
2, 3, 4
Select
2, 3, 4
…/†/œ/√
5
EXIT
Before adjusting!
Set the input mode to PC.
PC
Press the MENUbutton.
The main menu is displayed.1
Press the or button to move to Setup.
The Setupmenu is displayed.
Press the  button.
2
Press the or button to move to PC, then
press the  button.
The PCmenu is displayed.3
Press the EXITbutton to exit the menu.5
Press the or button to move to Fine, then
press the  button.
Press the œor √button to adjust.
4
PC
Auto Adjustment√
Coarse 1344
Fine 0
Zoom√
Reset√
Move
Enter Return
0 …
Fine
†
Downloaded From projector-manual.com Samsung Manuals 
						

							Connecting to PC
Zooming the Screen
65
1
MENU
2, 3, 4, 5
Select
2, 3, 4, 5
…/†/œ/√
6
EXIT
Zooming the Screen
Used to extend PC screen from the center.
Before adjusting!
Set the input mode to PC.
PC
Press the MENUbutton.
The main menu is displayed.1
Press the or button to move to Setup.
The Setupmenu is displayed.
Press the  button.
2
Press the or button to move to PC, then
press the  button.
The PCmenu is displayed.3
Press the EXITbutton to exit the menu.6
Press the , , œ, or √ button to move to
desired position, then press the  button to
extend as you want.
The screen can be extended by 1, 2, 4,or 8 times.
5
Press the or button to move to Zoom, then
press the  button.4
x2Move Zoom Return
PC
Auto Adjustment√
Coarse 1344
Fine 0
Zoom√
Reset√
Move
Enter Return
Downloaded From projector-manual.com Samsung Manuals 
						

							Connecting to PC
Reset the PC
66
1
MENU
2, 3, 4, 5
Select
2, 3, 4, 5
…/†/œ/√
6
EXIT
Reset the PC
Used to reset PC mode settings to the Factory Default values.
Before adjusting!
Set the input mode to PC.
PC
Press the MENUbutton.
The main menu is displayed.1
Press the or button to move to Setup.
The Setupmenu is displayed.
Press the  button.
2
Press the or button to move to PC, then
press the  button.
The PCmenu is displayed.3
Press the EXITbutton to exit the menu.6
Press the œor √button to move to OK, then
press the  button.
The PC is reset to the time of purchasing.5
Press the or button to move to Reset, then
press the  button.4
PC
Auto Adjustment√
Coarse 1344
Fine 0
Zoom√
Reset√
Move
Enter Return
Reset
Move
OKBack to Default Settings?Cancel
EnterReturn
Downloaded From projector-manual.com Samsung Manuals 
						

							Connecting to PC
Reset the PC
67
VISUAL REALISM
Troubleshooting
Before Contacting Service Personnel........68
Downloaded From projector-manual.com Samsung Manuals 
						

							Troubleshooting
Before Contacting Service Personnel
68
SymptomsTroubleshootingNote
Installation and Connection
Menu and Remote Control
Be sure that the power cord in place and the power switch
on the rear side of the projector is turned on 
-. 
No Power.Page 15
Be sure to make the projection beam perpendicular to the
screen and adjust the focus using the Zoom Knob and the
Focus Ring. Avoid to use the 
V-Keystonefunction if possible.
Image is distorted or
trapezoidal.Pages
16~20
Ceiling bracket is an optional accessory.
Please contact your dealer.Want to install
projector on ceiling.
Be sure that the connection cable (video) is properly
connected to the proper port. Unless they are connected
properly, the device is not available.Image is distorted or
trapezoidal.Pages
23~25
SymptomsTroubleshootingNote
Be sure that the proper external source is selected. 
Check batteries of the remote control. If there is a
problem, replace them with recommended ones.
Check the angle and distance between the remote control
and the projector. Be sure that there is no obstacle
between the projector and the remote control that may
block the signal.
Direct lighting of 3-way light bulbs or other lighting
device on the remote sensor of the projector may affect the
sensitivity and cause the remote control to malfunction.
Remote control does
not work.Page 26
Page 12
Page 13
Refer to the user manual. Some functions are locked
depending on sources and type of the input signal. Some of Menu functions
do not work.Pages
23~26
Before Contacting Service Personnel
If this projector does not operate properly, check the following first.
If the problem is continues, contact your dealer.
Downloaded From projector-manual.com Samsung Manuals 
						

							Troubleshooting
Before Contacting Service Personnel
69
Screen and External Source
SymptomsTroubleshootingNote
Be sure that the power cord of the projector is in place.
Be sure that the proper input source is selected.
Be sure that cable is properly connected to the rear panel
of the projector.
Check the Remote Control batteries.
Be sure that the Color, Brightnesssettings are not at their
lower limit.
Cannot see picture
images.Page 15
Page 26
Pages
23~25
Page 12
Page 31
Contact your service personnel if the noise continues due
to defective parts.Strange noise.
Adjust the Colorand Brightness.Poor color.Page 31
Adjust the focus.
Check that the projection distance is either too far or too
near to the screen.
Images are not clear.Page 16
Page 
19~20
Refer to instructions on lamp and repair.Repair indicator is on.Page 9
Noisy lines may appear for PC mode in case of frequency
discrepancy. Adjust the vertical frequency of your video
card on the advanced display property.Lines appear on screen.Page 63
Be sure to properly connect the external devices.
Especially, connect the component (Y, Pb, Pr) cables
matching the color codes.Green appears on the
screen.Pages
23~25
Be sure that the proper operation of the external device.
Adjustable items of the 
Custom PictureMenu are properly
set. Cannot see the picture
from the external
devices.Pages
26, 31
Be sure to properly connect the external devices.
Check the connection cables again.Only blue screen
appears.Pages
26,
23~25
Adjustable items of the  Custom PictureMenu are
properly set.
Execute Factory Defaultif you want to restore the factory
default setting values.
Screen appears in
black and white or
odd color/screen is too
dark or bright.Page 31
Page 48
Downloaded From projector-manual.com Samsung Manuals 
						

							Downloaded From projector-manual.com Samsung Manuals