Sanyo DP32670 Hdtv Lcd Owners Manual

11
ENGLISH
Location of controls
Front
To display the menu screen. 
Press MENU button to display the 
menu screen.
CHANNEL / buttons, VOLUME 
+/– buttons and INPUT/ENTER button 
can be used to select the desired 
setting during the menu screen 
operations. 
POWER buttonINPUT/ENTER button VOLUME +/– buttons
CHANNEL /1 
(PLAY) button
MENU button
POWER indicator
EJECT button
Left side
CHANNEL /3 
(STOP) button DISC slot
AC INPUT jack
HDMI 2 IN jack
HDMI 1/DVI IN jack
PC/DVI AUDIO IN jack
AUDIO (L/R) jacks...

12
How to attach the stand
NOTE:
•  Unplug the AC cord from the AC INPUT terminal.
•  Before beginning this process, assure that TV is laid on a clean, safe, and cushioned space to avoid any 
damage to the unit.
•  Do not touch or press the LCD-screen, glass might break under pressure.
Place the TV on its front onto a table.
Align the stand’s bottom-plate (supplied) as seen here.
It will fi t in only one direction.
Hold the unit and attach the stand slowly.
How to remove the stand
When you transport this...

13
ENGLISH
Remote control
POWER Power On/Off
DISPLAY Call TV information
Call DVD information
TV/DVD Switch between TV and DVD
 (EJECT) Eject a disc
0-9 Direct channel selection of TV
Input setting
Enter a password
– Input “–” for digital channels
SLEEP Sleep timer
SETUP/
TV MENUTV mode - Display menu of TV
DVD mode - Call up initial setup mode
PICTURE SIZE Display PICTURE SIZE menu
▲▼◀▶Cursor buttons
ENTER Enter information in the menu
MUTE Switch off the sound
EXIT/
CANCELExit from On-Screen menu
Reset...

14
Approximately 15 feet
Inserting Batteries
1Open the battery compartment 
cover in the direction of the arrow.2Install two “AA” batteries, paying 
attention to the polarity diagram 
in the battery compartment.3Replace the compartment cover.
Operation
Aim the remote control at the remote sensor and press control 
buttons to operate.
Operate the remote control within a 30° angle on either side of 
the remote sensor, up to a distance of approximately 15 feet. •
•
Remote control  (continued)
NOTE:
Do not...

15
ENGLISH
Antenna connections
If you are using an indoor or outdoor antenna, follow the instructions below that correspond to your 
antenna system. If you are using a Cable TV service, see page 16 for Cable TV connections.
Combination VHF/UHF Antenna (Single 75 ohm cable or 300 ohm twin-lead wire)
Combination VHF/UHF Antenna (Separate VHF and UHF 300 ohm twin-lead wires)
Separate VHF/UHF Antennas (75 ohm VHF cable and 300 ohm UHF twin-lead wires)
Connect the 75 ohm cable from the combination 
VHF/UHF...

16
Cable TV connections
For basic Cable TV service not requiring a Converter/
Descrambler box, connect the 75 ohm Coaxial Cable directly 
to the Antenna Jack on the back of the TV.
For subscribers to scrambled Cable TV serviceIf you subscribe to a Cable TV service which requires the use of a Converter/Descrambler box, connect 
the incoming 75 ohm Coaxial Cable to the Converter/Descrambler box. Using another 75 ohm Coaxial 
Cable, connect the output jack of the Converter/Descrambler box to the Antenna...

17
ENGLISH
Starting setup
The Starting Setup menu appears the first time 
you turn on the TV, and assists you to specify the 
Air/Cable setting, and program your channels 
automatically.
IMPORTANT: Make sure that the antenna or cable 
TV system connection is made!
1To turn on the TV, press POWER (POWER indicator 
on the front of the unit changes green. It may take 
approx. 10 seconds for a picture to appear on 
screen.). The starting setup function begins. 
Automatic Search StartThis unit has been preset...

18
When the TV receives a digital signal, the digital 
information will appear.
 62-1 HDTV Moving Picture1CH-1
Digital
No Program Information is availableSleep Timer
Off
English
Full
1080i
Air TV-MA
Channel number • Station name•
Channel label (if preset) •Broadcast program name•
V-Chip rating • Signal type•
Sleep timer • Audio language•
Program guide • Picture size•
Resolution •
When the TV receives an analog signal, the analog 
information will appear.
14Analog    Cable Sleep Timer
Off
Mono
Full
480iX...

19
ENGLISH
Convenience functions
You can change the default settings by pressing the Menu button on your remote, then select the one of  the 
icons at the top of the menu -  follow the On-Screen prompts to set your preferences.
Icon Selected Items Setup hint
Picture Picture 
SettingBrightness / Contrast 
/ Sharpness / Color 
/ TintYou can adjust the picture quality to your preference.
Color Temperature Bluish (Cool) / Neutral (Standard) / Reddish (Warm)
Backlight
*2The Backlight feature adjusts the...

20
Memorizing channels
This TV is equipped with a channel memory 
feature which allows channels to skip up or down 
to the next channel set into memory, skipping 
over unwanted channels. Before selecting 
channels, they must be programmed into the 
TV’s memory. To use this TV with an antenna, set 
the Signal Type option to the Air mode. When 
shipped from the factory, this menu option is in 
the Cable mode.
Air/Cable selection
1Select  “Channel”, then press ▶ or ENTER.
2Press ▲ or ▼ to select “Auto Ch...