Sanyo FVM4212hdtv Lcd Owners Manual

							2HDMI
3HDMI
HDMI
(DVI)
INPUT1
(MONO) (VIDEO)
VIDEOVIDEO
INPUT
VIDEO
INPUT1
2
AUDIO
(MONO)DIGITAL
AUDIO
OUTPUT
Please read before operating your HDTV!
PROTECTING THE LCD-
LED SCREEN
CAUTION: The screen can be damaged if
it is not maintained properly. 
•Do not use hard objects such as hard
cloth or paper to clean the screen.
•Do not use excessive pressure when
cleaning the screen; excessive pressure
can cause permanent discoloration or
dark spots.
•NEVERspray liquids on the screen.
HANDLING PRECAUTIONS
•Handle by the cabinet only. 
•Handling by two or more people is rec-
ommended.
•Never touch the screen when handling.
•Handling damage is notcovered under
warranty.
•Do not remove the protective film 
covering the front cabinet while 
handling the HDTV.
POSITIONING THE HDTV 
•Always use a firm and flat surface when
positioning your HDTV. 
•Do not position the unit in a confined
area. 
•Allow adequate space for proper venti-
lation.
•Do not position the HDTV where it is
easily reachable by small children and
may present risk of injury.
•Once HDTV is positioned, remove the
protective film covering front cabinet.
SPECIFICATIONS
Power Requirement:
Source: AC 120V, 60Hz
AC Power Consumption:90 watts
Weight:31.2 lbs  (without stand)
Dimensions _________________________
WIDTH    HEIGHT   DEPTH
w/stand38.9 24.7 7.7
w/out stand38.9 23.7 2.9
NOTE: Dimensions are in inches
GETTING STARTED
Hook up your antenna or your cable
service to the HDTV’s ANTterminal
with the use of a 75 OHM coaxial cable.
NOTE: Keep your indoor antenna at
least 3 ft. away from the televi-
sion set and any other electron-
ic equipment.
The tuner in this HDTV can receive:
• 
Digital and Analog off air signals
from an antenna
• Analog or ClearQAM cable channels
from a direct Cable TV connection.
ANTENNA CONNECTION FOR
OFF-AIR SIGNALS OR CABLE
ANTENNA
CABLEANALOG / DIGITAL
ANTENNA IN
AV INPUT SELECTION
Press the INPUTkey to select the 
correct AV input for the video source
you wish to watch.
NOTE: Unused AV inputs may be dis-
abled with the Input Setting feature.
Finish SetupRepeat
Channel Search Result: Succesfully Completed
If you are having problems, call us toll-free at 1-800-877-5032
Analog Channels
Video 1 Video 2 HDMI 1 HDMI 2
Digital Channels 16 26
HDMI 3
Before proceeding, please make
sure to correctly hook up your
antenna or cable connection and
all AV equipment to your HDTV.
1. PLUG IN AC POWER CORD
120V AC, 60Hz
2. TURN ON TV
3. TV SET LOCATION SELECTION:
Select “
Home Mode” to set the
HDTV’s backlight to an Energy Star
qualified level, or select “
Store
Mode” to set the backlight to a retail
display level.
4. CHANNEL AND SIGNAL SEARCH:
Select “
Signal Search” and press
ENTERto perform a channel search
from an Antenna or a direct Cable
connection, and a signal search
from devices hooked up to the
HDTV’s AV input jacks.
5. SIGNAL SEARCH RESULT SCREEN
The final setup screen displays ana-
log and digital channels found, as
well as AV inputs detected.
Select 
Finish Setupand press
ENTER.
NOTE: If you wish to repeat the
process, select Repeat.
INITIAL CHANNEL SEARCH
Need help? www.sanyoctv.com              1-800-877-5032Need help? www.sanyoctv.com              1-800-877-5032
1JC0P1P0023 - -Part No.:
Owner’s 
Manual
(English)
© 2012 Sanyo Manufacturing Corporation
1080p HDTV LCD
42” LED
1080p HDTV LCD
Model No.:
FVM4212
As an Energy Star®Partner,
Sanyo Manufacturing Corporation
has determined that this product
meets the Energy Star
®guide-
lines for energy efficiency.ENERGY STAR
TRADEMARKS________
Manufactured under license from Dolby
Laboratories. “Dolby” is a trademark of
Dolby Laboratories.
HDMI, the HDMI Logo and High-Definition
Multimedia Interface are trademarks or regis-
tered trademarks of HDMI Licensing LLC in
the United States and other countries.
Manufactured under license from Audyssey
Laboratories. U.S. and foreign patents pending.
Audyssey Dynamic Volume
®is a registered
trademark of Audyssey Laboratories.
HDTV INPUT/OUTPUT REFERENCE ________________________________________
4
6
HDTV BACK PANELHDMI (INPUT1, INPUT2 & INPUT3)
Use HDMI INPUT1, 2 & 3to hookup HD digital devices such
as a Blu-ray player, HD Cable Box, HD Satellite Receiver or
Video-game System.
Connect your digital device’s HDMI output to any of the
three (3) HDMI inputs on your HDTV with the use of an HDMI
cable.
NOTE: A DVI connection is possible via the HDMI (DVI) INPUT1
using an appropriate cable or adapter and connecting the
audio to the AUDIO mini stereo jack.
Analog / Digital Antenna Input
Hook up your indoor or outdoor digital antenna, or a direct
Cable service (Analog or ClearQAM).
USB
USB input jack is used to connect a USB mass storage
device to watch digital images stored in JPEG format.
AUDIO mini stereo jack (3.5mm)
For AUDIO signal from DVI device (using HDMI INPUT1).
Digital Audio Output (Coaxial)
Hookup a multichannel receiver with the use of a phono-
type digital audio cable.
VIDEO INPUT1(COMPOSITE)
Yellow (Video), plus white and red (Audio)  input jacks.
COMPOSITE connections are used to hookup your analog
equipment such as a VCR or an older DVD player.
NOTE: Match the color of your device’s output jack, the con-
nector and the HDTV’s input jack.
VIDEO INPUT2 (COMPONENT)
Green (Y), blue (Pb), and red (Pr) Video inputs plus the
white and red Audio inputs.
COMPONENTconnection will accept SDTV, EDTV and
HDTV video signals. Use it for great image quality from di-
gital devices such as a DVD player or Video Game system.
Match your digital device’s Component output jacks to the
Component input jack set (VIDEO2) on your HDTV.
NOTE: A composite connection is possible via VIDEO INPUT2
using the Y (VIDEO) jack and the L/R audio jacks (see
Video2 Setting.)
1
2
3
4
5
6
7
Printed in Mexico, April 2012
US2J  /  42-Z5GK  /  GXBM Sanyo Manufacturing Corp. 3333
Sanyo Road, Forrest City, AR 72335
2
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider than
the other. A grounding-type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided
for your safety. If the provided plug does not fit fully into your out-
let, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched par-
ticularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11. Only use attachments/accessories specified by the 
manufacturer.
12. Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13.  Unplug this apparatus during lightning storms or when unused
for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate nor-
mally, or has been dropped.15. If an outside antenna is connected to the television equipment,
be sure the antenna system is grounded so as to provide some
protection against voltage surges and built up static charges.
In the U.S. Selection 810-21 of the National Electrical Code pro-
vides information with respect to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding conductors, location
of antenna discharge unit, connection to grounding electrodes,
and requirements for the grounding electrodes.
16. An outside antenna system should not be located in the vicini-
ty of overhead power lines or other electrical light or power
circuits, or where it can fall into such power lines or circuits.
When installing an outside antenna system, extreme care
should be taken to keep from touching such power lines or cir-
cuits as contact with them might be fatal.
EXAMPLE OF ANTENNA GROUNDING ACCORDING
TO NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
“Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC that provides guidelines for
proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the build-
ing, as close to the point of cable entry as practical.”
17. Wall or Ceiling Mounting—The product should be mounted to
a wall or ceiling only as recommended by the manufacturer.
18. Apparatus shall not be exposed to dripping or splashing, and no
objects filled with liquids, such as vases, shall be placed on it.
19. When the MAINS plug is used as the disconnect device, the
disconnect device shall remain readily operable.
RISK OF ELECTRIC SHOCK   DO NOT OPEN!
CAUTION: TO REDUCE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK
OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTE-
NANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS UNIT.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
FCC INFORMATION________________________________________________
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.  This equipment gen-
erates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harm-
ful interference to radio communications.  However, there is no guarantee that interference will not occur in a particular installation.  If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following  measures:  
– Reorient or relocate the receiving antenna.  
– Increase the separation between the equipment and receiver.  
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
– Consult the dealer or an experienced radio/TV technician for help.
CAUTION: FCC Regulations state that improper modifications or unauthorized changes to this unit may void the user’s authority to 
operate the unit.
This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way that it does not require
a safety connection to electrical earth.
Install two (2) “AAA” batteries in the
remote control. (Not included)
PRECAUTIONS:
• Replace both batteries at the same
time. Do not use a new battery with a
used battery. 
• There’s a risk of explosion if a battery
is replaced by an incorrect type.
• Keep away from moisture.
• Be sure to match the “+”and “–”
signs on the batteries with marks
inside the remote control.
• Please properly dispose of used up
batteries.
WARNING: The batteries (or battery
pack) shall not be exposed to excessive
heat such as sunshine, fire or the like.BATTERY INSTALLATION
3
1
7
5
The American Academy of Pediatrics dis-
courages media use by children younger
than two years. For more information,
visit www.aap.org
.
SANYO television customers
should contact MRM
Recycling at 888-769-0149 or
visit their website at
www.mrmrecycling.com
regarding SANYO’s waste
management plan.
ENERGY STAR is a set of power-saving guidelines issued by the U.S. Environmental Protection
Agency (EPA). ENERGY STAR is a joint program of the U.S. Environmental Protection Agency and
the U.S. Department of Energy helping us all save money and protect the environment through
energy efficient products and practices.
Changes to default as-shipped television configuration and settings or enabling certain optional
features and functionalities will change the energy consumption of the television, this may
increase energy consumption beyond the limits required for ENERGY STAR qualification.
Wall mounting of the HDTV must be
performed by a skilled person.
For foot stand disassembly (if needed):
•Place HDTV face down
on a padded or
cushioned flat surface to protect the
screen and finish.
•Remove the two (2) screws securing
each foot stand. CAUTION:Hold the
stands firmly as you remove screws.
1Remove the four (4) M6x12 screws
threaded in the VESA holes on the
back of the TV.
2Use the removed screws to secure
the TV to a wall mounting kit.
NOTE: Wall mounting kit is not included.
VESA standard interface:  200 x 200
Mounting screws measurements: 
Diameter: M6 (6mm) Length: 12mm
WALL MOUNTING(OPTIONAL)
NOTE: Skip these steps if you are wall
mounting the TV.
1Place HDTV face downon a
padded or cushioned flat surface
to protect the screen and finish.
2Carefully insert both foot stands to
the bottom of the HDTV and
secure each one by inserting a
M4x30 screw on top, and the
longer M6x40 screw on the bottom
as indicated in the diagram below.
NOTE: Foot stand screws are found in
the literature package.
3Position the HDTV on a firm and
flat surface with adequate space
for proper ventilation.
STAND ASSEMBLY______
M4x30 
M6x40  
						

							REMOTE CONTROL OPERATION _______________________________
Auto –Searches the detected mode,
Cable or Air.
Cable –Searches for analog and
unscrambled (ClearQAM) digital cable
channels.
Air (Antenna) –Searches for analog
and digital off-air channels.
Digital Add-On –Searches digital chan-
nels adding newly found digital chan-
nels to the channel database.
Channel Search
Display the On Screen menu and use
the CURSORkeys to select
Channel. Press ENTER.
ON-SCREEN MENU
OPERATION
Channel Scan Memory lists all Analog
and Digital channels found. It also lists
Analog channels that were not found,
which can be added.
Use the CURSORkeys to move the
channel select bar through all enabled
and disabled channels.
NOTE: You can use the CHkeys to
change page.
Press ENTERto enable or disable the
selected channel.
NOTE: For information on local digital
channels, visit www.antennaweb.org
Channel Scan Memory
Channel Scan Memory
MoveSelectENTERPageCHExitEXITReturnMENU
TVAnalog
Digital
Digital
Analog
Analog
Analog
Digital03
03-1
03-2
04
05
06
06-1WREG-DT
WCVB
WEXT
NICK
NICK
VBCT
IMPORTANT FACT:This HDTV maintains only
one database of digital channels. Therefore,
when you search for cable channels, the
database of antenna digital channels will be
deleted. You will only be able to receive those
ClearQAM channels your cable company
provides. 
Input Setting feature allows the
removal of unused inputs from the AV
input loop.
Use the CURSORkeys to select an
AV input. Press ENTERto disable
(uncheck) or enable (check) the high-
lighted  input.
NOTE: At least one input must and
will remain checked.
Unchecked box     means the input will
be skipped
Input Setting
Channel Setting
MoveSelectENTERExitEXITReturnMENU
TVChannel Search
Channel Scan Memory
Input Setting
Video2 SettingVideo1
Video2
HDMI1
HDMI2
HDMI3
USB
:Skip
Use this feature to establish either a
Component or Composite connection
to the VIDEO INPUT 2 jacks on your
HDTV.
Use the CURSORkeys to select the
type of connection you’ll use in VIDEO
INPUT 2. 
Press ENTER, a blue mark will appear
next to the selected option indicating it
as the active option.
Video2 Setting
SETUP
Display the On Screen menu and use
the CURSORkeys to select Setup.Press ENTER.
Menu Language
Choose between English, Spanish and
French for your On Screen menu’s dis-
play language. 
Press ENTERon the desired language.
Captioning is textual information trans-
mitted along with the picture and
sound. Turning Captioning ON (by
pressing the CAPTIONkey during nor-
mal TV viewing) causes the HDTV to
open these captions (digital or 
analog) and superimpose them on the
screen.
NOTE: Local broadcasters decide
which caption signals to transmit.
Use the CURSOR andkeys to
modify Font, Background,andForegroundof digital caption text.
Digital Caption
This feature allows you to set aCurrent Timefor your HDTV and
enable a Switch On Timefor the HDTV
to turn on at a specific time of day.
When 
On Timer Functionis set to ON,
the TV will automatically turn on at the
previously set 
Switch on Time.
Use the CURSOR andkeys to
modify the 
Current Timeand/or Switch
On Time.
Clock Timer
Use this feature to automatically block
programs with content you deem as
inappropriate for viewing by your 
children.
NOTE: This feature is designed to com-
ply with the United States of
America’s FCC V-Chip regula-
tions. Therefore, it may not func-
tion with broadcasts that origi-
nate in other countries.
ADJUSTING THE V-CHIP RATINGS
Select 
ONand press ENTER. SelectAdjust (Standard)and press ENTER.
NOTE: Blocking a rating will automati-
cally block all higher ratings.
Unblocking a rating will auto-
matically unblock all lower 
ratings.
For V-Chip (Movie) ratings select Movieand press ENTER, and then select the
desired MPAA rating limit. Press the
EXITkey to close the V-Chip menu.
V-Chip (parental control)
For V-Chip (TV) ratings select TVand
press ENTER. Use the CURSOR 
keys to select a rating and press ENTER.
Use the CURSOR keys to set the
rating’s status as 
Blockedor Viewable.Once ratings are set, press the EXITkey
to close the V-Chip menu.
NOTE:Some TV ratings offer more
detailed settings such as
Dialogue, Language, Sexual,
and Violence. 
SetupMenu Language
V – Chip
Digital Caption
Energy Solution
Clock Timer
Mode (Home/Store)Off
On
Adjust (standard)
MoveSelectENTERExitEXITReturnMENU
TV
ADVANCED V-CHIP SYSTEM (RRT5)
RRT5 (V-Chip Regional Ratings 5) is an
advanced V-Chip ratings system for over
the air digital channels.When the HDTV
detects compatible RRT5 data, it’s
downloaded & stored in memory, and
the Setup V-Chip screen is then mod-
ified to show the 
Adjust (Advanced)option.
Use the CURSOR and  keys to
highlight the different options, and use
the ENTERkey to block or unblock the
selected rating.
NOTE: When vertical scroll bars appear,
press  CURSORto gain
access to the additional ratings.
MORE INFORMATION
Additional information about MPAA
(Motion Picture Association of
America) and V-Chip rating can be
found at: www.mpaa.org and
www.v-chip.org, respectively.Display the On Screen menu and use
the CURSORkeys to select
Picture. Press ENTER.
You may choose between 
Vivid, Mild,and Standard, which have predeter-
mined fixed picture parameter 
values, or choose the 
Manualoption
for customized personal settings.
NOTE: Each AV input can have its
own picture mode (pre-deter-
mined or manual.) Current
input’s selected option is indi-
cated by a blue marker.
MANUAL PICTURE SETTINGS
Manualparameters to adjust include:
• 
Color• Tint
• Contrast         • Brightness
• Sharpness      • Color Temperature
The Detailed Settingoption allows for
the adjustment of several additional
parameters such as:
• 
Signal Balancer• Noise Reduction
• White Balance• Edge Enhancer
• H-Size / V-Size     • Dynamic Contrast
PictureVivid
Mild
Standard
ManualColor
Tint
Contrast
Brightness
Sharpness
Color Temperature
Detailed Setting
Default
MoveSelectENTERExitEXITReturnMENU
TV
ADJUSTING A PICTURE SETTING
Use the CURSORkeys to highlight
the picture parameter you wish to
adjust. Press the ENTERkey to enter the
value adjustment screen. Modify the
selected parameter’s value by pressing
the CURSOR keys.
NOTE:CURSOR  keys select the
next/previous parameter with-
out returning to the previous
menu screen.
Once adjustments are complete, press
the EXITkey to return to normal TV
viewing.
Display the On Screen menu and use
the CURSORkeys to select
Sound. Press ENTER.
Choose sound setting option:
Auto– Sound settings are linked to
the current Picture option and param-
eters are adjusted accordingly.
Dynamic, Mild, Standard–
Predetermined sound parameters not
linked with any Picture option.
MANUAL SOUND SETTINGS
The Manualoption provides different
parameters that can be personally
adjusted:
• 
Bass & Treble    
• Bass Extension 
• Audyssey Dynamic Volume 1
• Detailed Setting
– Equalizer: 
Personalize audio highs
and lows.
Manual
Move
SelectENTERExitEXITReturnMENU
TVBass
Treble
Bass Extension
Audyssey Dynamic Volume
Detailed Setting
Default SoundON
Medium
ADJUSTING A SOUND SETTING
Use the CURSORkeys to highlight
the sound  parameter you wish to adjust.
Press the ENTERkey to enter the value
adjustment screen. Modify the selected
parameter’s value by pressing the 
CURSORkeys.
NOTE:CURSOR  keys select the
next/previous parameter with-
out returning to the previous
menu screen.
Once adjustments are complete, press
the EXITkey to return to normal TV
viewing.
1
Audyssey Dynamic Volume solves the 
problem of large variations in volume level
between television programs, commercials,
and between the soft and loud passages of
movies. Audyssey Dynamic EQ is integrated
into Dynamic Volume so that as the playback
volume is adjusted automatically, the per-
ceived bass response, tonal balance, surround
impression and dialog clarity remain the same.
NOTE: A thumbnail hide icon will
appear if a picture cannot be decoded
or if no thumbnail data is available.
View pictures on your HDTV with the
use of a USB mass storage device (not
included.)
HDMI(DVI)INPUT1
Insert the flash drive into the USB port,
the TV will display the Photo Viewer
screen, select 
Shuffle Playor Browse
Photosand press ENTERto begin.
USB FLASH
DRIVE
PHOTO VIEWER
USB INPUT
USING THE PHOTO VIEWER
Press ENTERon a thumbnail photo to
enable the Rotate, Full View and Start
Slideshowfunctions.
Once in 
Full Viewmode:
Use the CURSORkeys to change
picture.
Press ENTERto show the full view
options menu.
• 
Rotate• Zoom In / Out
• Pan• Slideshow setup
• Start Slideshow• Browse Photo
SLIDE SHOW
In the Slideshow Setupmenu you may
turn the Shuffleand Quick Changeoptions ONor OFF.
Press ENTERon 
Start Slideshoweither from the Thumbnail View
Screen or from the full view options
menu to start the slideshow from the
current picture. 
V-Chip (continued)
HDTV BACK PANEL
Your Sanyo HDTV is registered at the time of purchase, 
please keep sales receipt for future reference.
For your protection in the event of theft or loss of this product, please fill in the
information requested below and KEEP IN A SAFE PLACE FOR YOUR OWN 
PERSONAL RECORDS.
Model No. ______________________ Serial No. _____________________________
Purchase date ___________________ Purchase Price _________________________
Where Purchased _____________ ____________
(Located on back of unit)
ONE-YEAR LIMITED PARTS AND LABOR
WARRANTY
THIS LIMITED PARTS AND LABOR WARRANTY IS VALID ONLY ON SANYO TELEVISIONS
PURCHASED AND USED IN THE UNITED STATES OF AMERICA, CANADA, AND PUERTO
RICO, EXCLUDING ALL OTHER U.S. TERRITORIES AND PROTECTORATES. THIS LIMITED
WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL PURCHASER, AND DOES NOT
APPLY TO PRODUCTS USED FOR INDUSTRIAL OR COMMERCIAL PURPOSES.
WARRANTY APPLICATION
FOR ONE YEARfrom the date of original retail purchase Sanyo Manufacturing 
Corporation (SMC) warrants this TV to be free from manufacturing defects in materials and
workmanship under normal use and conditions for parts and labor. 
For the FIRST 90 DAYSfrom the date of original retail purchase, Sanyo Manufacturing
Corporation will replace any defective TV via exchange at the retailer. To ensure proper
warranty application, keep the original-dated-sales receipt for evidence of purchase.
Return the defective TV to the retailer along with the receipt and the included 
accessories, such as the remote control. The defective TV will be exchanged for the same
model, or a replacement model of equal value, if necessary. Replacement model will be
contingent on availability and at the sole discretion of Sanyo Manufacturing Corporation.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
OBLIGATIONS
For one year
from the date of purchase, Sanyo Manufacturing Corporation warrants 
this product to be free from defects in material and workmanship under normal use and 
conditions. During the first 90 days
under this warranty for any manufacturing defect or 
malfunction Sanyo Manufacturing Corporation will provide a new TV via exchange at
the retailer.
HOW TO MAKE A CLAIM UNDER THIS WARRANTY
Please call 1-800-877-5032. Please be prepared to give us the television’s model number
and serial number when you call. The model number and serial number are printed on a
label attached tothe back of the unit.
For customer assistance, call toll free 1-800-877-5032.
This warranty expresses specific contractual rights; retail purchasers may have addition-
al statutory rights which vary from state to state.
(EFFECTIVE: March 1, 2007)
(Located on back of unit)
CHANNEL
PICTURE
SOUND
ECO ONTIMER
SUB CH
INFO DYN VOL
POWER. Turns your HDTV On or Off.
INPUT
. Selects the video source to
view. Holding down the key displays
the Input List.
ECO
. Modifies the Energy Saverlevel.
AUDIO
. Selects the desired Audio
mode. Stereo, Mono, or SAP (when
available.)
ON TIMER
. Displays the current switch
on time (if activated.)
CAPTION
. Cycles through the available
Caption modes (when available.)
RESET
. Pressing it twice restores your
HDTV to its factory settings. All user
customized settings will be cleared.
SLEEP
. Displays the “Off” Timer. While
Off Timer is on-screen, press the “0”
key to Set the amount of time (in 30
minute increments) at which the HDTV
will turn off.
NUMERIC KEYS
. Choose a channel
directly.
CH 
. Scan through the channels in
the memory database.
VOL + – – 
 
. Increases or decreases the
audio level.
RECALL
.Switch between current chan-
nel and last selected channel or input.SUB CH
. Use for the direct selection of
digital subchannels. For example: for
channel 39.1 press the 
3and 9 keys,
followed by the dash 
– –, and 1keys.
MUTE
. Mute or restore the sound.
INFO
. Displays theChannel Information
banner.
PIX SHAPE
. Cycles through the various
aspect ratios. The different settings
either stretch, zoom, or fill the image
on your screen. Bars may appear on
top and bottom of your screen (or on
left and right sides) depending on the
broadcasted signal or program.
DYN VOL
. Modifies the Dynamic
Volume feature  settings
MENU
. Display or hide the on-screen
menu.
HELP
. Displays the on-screen Help menu.
CURSOR
. Move the on-screen
cursor in the desired direction.
ENTER
. Set or select the highlighted
option on the screen.
EXIT
. Exits the on-screen menu.
Energy Solution
ECO (ENERGY SAVER)
ECO controls the LED backlight bright-
ness to reduce power consumption.
– Level 1: Energy Saver feature is off.
– Level 2: Low power consumption.
– Level 3: Lowest power consumption.
Press ENTERon the desired level.
LIGHT SENSOR
This feature detects ambient room
light brightness and uses that reading
to control the panel brightness level
and picture parameters to reduce the
HDTV’s power consumption.
NOTE: When room lighting is dark,
the panel brightness and/or the
picture setting parameters
such as brightness and con-
trast are lowered. When room
lighting is bright, parameters
are affected opposite.
Use the CURSORkeys to select Onor OFFand press ENTER.
AUTO SHUT-OFF
When Auto Shut-off feature is set toON, it will allow the HDTV to automa-
tically turn off when no video and/or
audio signals are being received.
NOTES: By factory default, this fea-
ture is set to ON. The HDTV
will automatically turn off if
no AV signals are received in
a time span of 15 minutes.
Use the CURSORkeys to select Onor OFFand press ENTER.
Use the Mode (Home/Store)option if
you would like to change the initial
Energy Saving Mode chosen at HDTV’s
first power on.
Home Mode -For saving energy and
power consumption reduction.
Store Mode -High brightness and 
contrast for display at retailer store.
NOTE: Only Home Mode qualifies for
Energy Star.
Press ENTERon the desired mode.
Mode (Home/Store)