Home > Sanyo > Television > Sanyo Lcd 27xa2 Instruction Manual

Sanyo Lcd 27xa2 Instruction Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Sanyo Lcd 27xa2 Instruction Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 550 Sanyo manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							INSTRUCTION MANUAL
    LCD Colour TelevisionLCD-27XA2
    LCD-32XA2
    P
    Please read this Instruction Manual before using your television.
    We wish you many hours of pleasure from your new television.
    Inst. Manual_N2WW(UE2-A)  5/30/05 3:08 PM  Page 1
     
    						
    							2 2
    Warnings and Cautions
    Minimum Distances
    5 cm
    10 cm
    10 cm10 cm
    Warning
    High voltages are used in the operation of this
    television receiver. Do not remove the cabinet
    back from your set. Refer servicing to quali-
    fied service personnel.
    Do not drop or push objects into the televi-
    sion cabinet slots or openings.
    Never spill any kind of liquid on the television
    receiver.
    Caution
    Avoid exposing the television receiver to direct
    sunlight and other source of the heat.
    If the television is to be built into a compartment
    or similarly enclosed, the minimum distances
    must be maintained. Heat build-up can reduce the 
    Do not block the ventilation holes in the back
    cover. Adequate ventilation is essential to prevent
    failure of electrical components
    .
    Cleaning the TV Monitor
    Do not pressDo not hit
    Be sure to disconnect the AC Power Cord from
    AC outlet before cleaning the TV monitor.
    Gently wipe the screen
    and cabinet with dry soft
    cloth. Screen is likely dam-
    aged if it is not maintained
    properly. Do not use hard
    cloth or paper. Do not use
    solvents or abrasive.
    Do not use benzene, thin-
    ner or any volatile sub-
    stances to clean the TV
    monitor. These chemicals
    may damaged the cabinet
    finish.
    Caution
    Care for Using TV Monitor
    Screen likely damaged by external shock. When
    using the TV monitor, following precautions
    should be taken.
    Do not press or hit the screen face.
    Do not write, paint or affix anything on the screen.
    Do not put anything on the TV monitor. service life of your television, and can also be
    dangerous.
    If the LCD panel is broken and leaks liquid
    crystal, do not touch it. Moreover, never swal-
    low or suck the liquid, or touch the liquid with
    your skin. In case the liquid drops in your
    mouth or eyes, clear it by water adequately at
    once and go to see a doctor. If not, there is a
    possibility causing poisoning. If the liquid
    drops on skin or clothes, also clear it by water
    adequately at once, if not, the skin or clothes
    will be damaged. To prevent fire or electrical shock hazard, do
    not expose the television receiver to rain or
    moisture.
    Inst. Manual_N2WW(UE2-A)  5/30/05 3:08 PM  Page 2
     
    						
    							ANT.75Ω
    Installation
    3 3
    Step 1 : Connecting the Aerial and Power Supply
    •Connect your aerial cable plug to the rear of the TV set.
    For further information please consult your local dealer.
    •Connect the AC power plug to the wall socket (AC100-264 Volts, 50Hz/60Hz).
    Note:The form of the AC code and AC plug are different with each country.
    Inst. Manual_N2WW(UE2-A)  5/30/05 3:08 PM  Page 3
     
    						
    							4 4
    Installation
    Step 3 : Switching on/Plug & Play
    Use 2 “AAA” 1.5 volt batteries.
    Be sure batteries are installed correctly.
    Note:Do not mix old batteries with new ones or mix different type of batteries together.
    Step 2 : Battery Installation of the Remote Control Transmitter
    Let’s start ! Let’s start !
    This TV set provides a self-automatic tuning system function called “Plug & Play”.
    It automatically begins searching and storing of all available channels when switching-on the
    TV set for the first time.
    1 1Press the Power ON/OFFbutton to turn the TV on, and the TV set will search and store of
    all available TV channels automatically.
    2 2After completing Plug & Play, press the MENUbutton  to return to the normal TV mode.
    ✐ This procedure only appears at the first switch-on time.
    Now the installation is completed ! 
    Inst. Manual_N2WW(UE2-A)  5/30/05 3:08 PM  Page 4
     
    						
    							Control Panel
    5 5
    P
    Each button listed this section has the same function as it’s corresponding button on the
    Remote Control
    Programme
    Up/Down
    Power ON/OFF
    button
    Remote Control
    DetectorStand-by and
    Power Indicator
    Volume
    P
    360˚
    Do not position hand under the screen frame
    while rotating the TV.
    Caution
    Viewing Angle Adjustment
    Swivel stand is rotated 360˚ right and left.
    Inst. Manual_N2WW(UE2-A)  5/30/05 3:08 PM  Page 5
     
    						
    							CS
    6 6
    Remote Control Transmitter
    TV/AV Selector
    Recall/Colour System
    Numeric buttons
    Digit
    TEXT/TV Stereo/Mono
    BASS
    Power ON/OFF
    Sound Mute
    Wide
    Alternate
    Volume +/-
    Picture Mode
    SURROUND
    MENU
    To select the next or previ-
    ous programme position.
    Digital Shot
    TIMER
    DVD button
    Programme Up/Down
    Sound Mode
    CS button
    OK button
    Cursors 
    These buttons are not used.
    VCR and DVD button
    To call up the List screen of
    the Digital Shot. To increase or decrease the
    sound volume level.
    Press repeatedly to switch to
    TV, AV1, AV2, AV3, AV4 or
    AV5 mode.
    Red
    Green
    YellowBlue
    To call up the Timer menu
    directly.
    To select half mute, full
    mute or restore the sound.
    Inst. Manual_N2WW(UE2-A)  5/30/05 3:08 PM  Page 6
     
    						
    							7 7
    General Operation
    Press the Power ON/OFFbutton to
    turn on or off (Stand-by) the TV set.
    Power ON/OFF(Stand by)  Power ON/OFF(Stand by) 
    Auto Shut Of Auto Shut Of
    f Function f Function
    -/- -
    Alter Alter
    nate nate
    Press the Alternatebutton, and the
    programme position will alternately
    select the previous position and the
    present position.
    Pictur Pictur
    e Mode Selection e Mode Selection
    Press the Picture Modebutton
    repeatedly to select the following
    picture modes;
    Personal :Your personal preference mode.
    Standard:Normal viewing mode.
    Dynamic:Suitable for brightly lit room.You can turn on the TV in the standby mode
    by pressing the following buttons in addition
    to the Power ON/OFFbutton.
    ●Programme Up/Down button of the 
    remote control transmitter or the TV set.
    ●1to 9,0 button on the remote control 
    transmitter.
    If the TV is left on after you have gone to
    sleep, the TV set changes to the standby
    mode within 10 minutes after all broadcasts
    have ended.
    Lighting of the Stand-by and Power Indicator
    shows that there is a power supply. For shut-
    ting off a power supply completely, discon-
    nect the power cord from the power outlet.
    Bass Expander On/Of Bass Expander On/Of
    f f
    Press the BASSbutton to get an 
    emphasised bass sound. Press the Sound Modebutton
    repeatedly to select the following 
    sound modes;
    Personal:
    Your personal preference mode.
    Music:Suitable for music programme.
    Ta l k :Suitable for news programme.
    Normal:Normal listening mode.
    Sound Mode Selection Sound Mode Selection
    Active 3D Surr Active 3D Surr
    ound ound
    Press the SURROUNDbutton to
    switch 3D Surround on (Active)
    and off.
    Dir Dir
    ect Pr ect Pr
    ogramme Selection ogramme Selection
    Example:
    ■Press 6button to select programme 
    position 6.
    ■ To select programme position 27, press 
    the Digitbutton, press 0, 2then 7button.
    or
    Press the Digitbutton, press 2, 7button 
    and wait for 5 seconds.
    ■ To select programme position 215, press 
    the DIGIT button, press 2,1then 
    5button.
    -/- -
    -/- --/- -
    -/- --/- -
    -/- -
    -/- -
    -/- --/- -
    -/- -
    -/- -
    -/- --/- --/- --/- -
    Inst. Manual_N2WW(UE2-A)  5/30/05 3:08 PM  Page 7
     
    						
    							8 8
    General Operation
    Pr Pr
    ogramme Infor ogramme Infor
    mation Call mation Call
    To display the on screen indication, press
    the Recall/Colour Systembutton.
    A2 Ster A2 Ster
    eo, NICAM Ster eo, NICAM Ster
    eo eo
    and Bilingual Br and Bilingual Br
    oadcast oadcast
    Receiving Receiving
    ■A2 Stereo and NICAM Stereo sound
    reception
    ■ Bilingual reception
    If the TV receives bilingual programs, the
    TV initially selects language A and displays
    “A” on the screen briefly. If you want to
    switch to language B or Mono (only avail-
    able in NICAM reception), press the Stereo/
    Monobutton.
    A2 Bilingual 
    When receiving NICAM stereo broadcast,
    NICAMwill be displayed on the screen. For
    A2 (German) stereo broadcasts, Stereowill
    be displayed. When a clear stereo sound
    can not be obtained during NICAM or A2
    (German)  stereo broadcast due to poor 
    signal reception, press the Stereo/Mono
    button to select mono mode.
    NICAM Stereo
    A2 Stereo
    NICAM Bilingual 
    Sound Status
    Off-timerProgramme Position
    Sound System
    OFF  02:00
    Mono
    A
    NICAM
    AUTO
    BG
    Colour System Selection Colour System Selection
    If the clear picture cannot be obtained, press
    the Recall/Colour System button repeated-
    ly until optimum image can be produced.
    SECAM
    NTSC4.43
    A colour system entry to the memory can
    not be made during TV mode, make it
    during Semi-auto tuning mode.
    NTSC
    PA LAUTO
    Colour System
    Stereo
    NICAM
    Mono
    B
    Mono
    AB
    03
    Inst. Manual_N2WW(UE2-A)  5/30/05 3:08 PM  Page 8
     
    						
    							Auto
    It automatically switches to the optimum screen mode according to the WSSsignal provided
    in the receiving signal source. If the signal does not have it, the TV keeps current screen mode.
    This setting may cause the picture to change when a different format is received e.g. when an
    advert is received.
    WSS (Wide-Screen-Signalling)
    This function is to be automatically set to the optimum screen mode for the wide screen 
    television according to the aspect ratio bits of the picture format (16:9, 14:9, 4:3, etc.) on 
    the receiving signal source. To use this function, the picture mode should be selected to 
    the “Auto” mode. This function is also effective in the AV mode. When you connect AV 
    equipment which has the WSSfunction, the screen mode is automatically selected to the 
    optimum screen mode.Press the Wide button to select the following screen modes;
    Auto/ Natural/ Zoom 14:9/ Title-in 14:9/ Zoom 16:9/ Title-in 16:9/ Full/
    Normal
    General Operation
    9 9
    Natural
    Scr Scr
    een Mode Selection een Mode Selection
    Today there are various transmission formats with different size ratios, e.g. 4:3, 14:9, 16:9
    and video format such as letterbox. 4:3 picture sometimes have a black band at the top and
    bottom of the screen. You can select a screen mode to optimise the picture display.
    4:3 14:9 16:9
    Letterbox Video
    Stretches the picture
    horizontally to fill the
    screen, the picture is
    more stretched at the
    edges.The height is expand-
    ed to fill the whole
    screen.The picture fills the
    screen and is propor-
    tionally correct.The black bars top
    and bottom remain
    and the height is
    compressed to fit into
    the picture area.
    Inst. Manual_N2WW(UE2-A)  5/30/05 3:08 PM  Page 9
     
    						
    							10 10
    General Operation
    Title-in 14:9
    Zoom 16:9 Zoom 14:9
    4:3 14:9 16:9
    Letterbox Video
    The correct picture
    width is maintained
    but the top and 
    bottom are cropped.Zooms in slightly
    cropping the top and
    bottom.Zooms in slightly
    cropping the top and
    bottom.The black bars top
    and bottom are small-
    er and the picture
    height is compressed
    slightly.
    TITLES ON SCREENTITLES ON SCREENTITLES ON SCREENTITLES ON SCREEN
    4:3 14:9 16:9
    Letterbox Video
    As zoom (14:9), but
    bottom is compressed
    even more to allow
    subtitles to be seen.As zoom (14:9), but
    bottom is compressed
    even more to allow
    subtitles to be seen.As zoom (14:9), but
    bottom is compressed
    even more to allow
    subtitles to be seen.As zoom (14:9), but
    bottom is compressed
    even more to allow
    subtitles to be seen.
    4:3 14:9 16:9
    Letterbox Video
    The correct picture
    width is maintained
    but the top and bot-
    tom are cropped.Zooms in slightly
    cropping the top and
    bottom.Zooms in slightly
    cropping the top and
    bottom.The black bars top
    and bottom are small-
    er and the picture
    height is compressed
    slightly.
    Inst. Manual_N2WW(UE2-A)  5/30/05 3:08 PM  Page 10
     
    						
    All Sanyo manuals Comments (0)

    Related Manuals for Sanyo Lcd 27xa2 Instruction Manual