Sanyo LNS-T01z, LNS-w01z Installation Manual

1AA6P1P2629--  (ICPWZ)
÷	¥Óé´£«»”èï¶

èï¶w	“
ÇZz‡hx¦õwKqtzS–Mts’sM
æ
¼U’”	ÔùUK“‡b{
\•’w
æ
¼x™Ô
žAqs”	ÔùUK“‡bwpzG
~t-`oXi^M{
Þ
†Ì¤w
$xîMw‹wqŸs”	ÔùUK“‡b{
	“
ÇZ^À	Íw«™
\wèï¶xzæÞ¯ï‡hx÷	¥Óé´£«»”Š.pw¶”ÜS‘|Ñ¥”§
µÐ
TxpV‡dœ{
Ô èï¶w	“
ÇZz¦õ^Àx±”ϵU	[»UæloXi^M{
Ô èï¶w	“
ÇZz¦õ^Àx\w^À		q	{t`hUMz
Y`XæloXi^
M{
Ô èï¶txèï¶-¢whŠw©ß¿ÓU...

 

ÇÅå Ì”
èï¶Ú¢ïÄÒå­¿Ä

$
èﶛ	“
ÇZ‡b{¢
$€	°£
 xa

LCD PROJECTOR LENS
MODEL NO. LNS-W01Z / LNS-T01Z
LENS REPLACEMENT 
AND INSTALLATION PROCEDURES
NOTES ON REPLACEMENT AND INSTALLATION
The procedures and the needed pars for lens installation depend on the type of
cabinet.  Before installing or replacing the lens, make sure the type of cabinet and be
sure to refer to the Installation Manual corresponding with your projector.
When installing or replacing the lens, make sure the Lens Model No. matches with
your projector.  Refer to the catalog, or contact...

Some parts are not used for installation or replacement.  Keep these parts for later use.
Note : Figures in this manual may be differ from the actual product.
NOTES ON LENS INSTALLATION
The ZOOM and FOCUS adjustment on the Top Control or the Remote Control can-
not be operated with this Lens.
• Lens installation and replacement should be made by the qualified service per-
sonnel.
• Be sure to install the lens following this procedure precisely.
• The lens cover is on the lens for protection.  Be sure to...

LENS REPLACEMENT AND INSTALLATION PROCEDURE
1. Remove screws A (2 screws).
2. Pull down the lower lens cover while pushing
the part D, then remove it.
3. Remove screws B (2 screws).
4. Remove screws C (2 screws) and remove
upper lens cover.
1
A
Fig-1
Fig-2
IN CASE OF MODEL WITHOUT LENS
Remove 2 screws and pull down the plate.
2
UPPER LENS COVER
LOWER LENS COVER
C
B
D
D
COVER PLATE
REMOVE THE LENS COVER. (See figure-1)
(At the step , insert the light-block sheet in
the same position as the removed cover...

MOUNT THE LENS COVER. (See figure-6)
INSTALL THE LENS. (See figure-4)
1. Remove protective caps(front and
back) on the lens.
2. Mount the lens on mounting bracket
of the main cabinet with 4 screws.
Use the screws included with the lens.
Use the driver included with the lens to
fasten the screws.
(After using, save it for latter use.)
3
A
INSTALL THE LIGHT-BLOCK SHEET. (See figure-5)4
Install the light-block sheet around the lens
as shown in the illustration.  Use the sheet
included with the lens.
When...