Sanyo LNS-T30KS/W30KS, LNS-T30KB/W30KB Parts Manual

Following checks and confirmations should be taken for safety.
Check the following things by the time of the cabinet assembly after the lens
replacement.
1. Confirm the lens is securely fixed by 4 screws.
2. Confirm the proper wiring and the wires are fixed properly.
3. Confirm the each connector is connected properly.
4. Wiring must not be tangled in the mechanical parts.
5. There is no missing part, or no loosing mounting part.
LCD PROJECTOR LENS
MODEL LNS-T30KS/W30KS
LENS REPLACEMENT PROCEDURE
NOTES...

Remove 4 screws on side cabinet and 1 screw
on rear.
Grasp the two sides, pull the cabinet top
upward and remove.
LENS REPLACEMENT PROCEDURE
REMOVE THE CABINET TOP (See figure-1)1
1.
2.
2
Fig-1
REMOVE THE CABINET FRONT (See figure-2)
Remove 2 screws on cabinet front bottom.
Grasp the two sides, pull the cabinet front
forward and remove.
Remove 2 speaker connectors, LED
connector K8K,  remote control pre-amp.
connector K18D and remove the cabinet
front completely.1.
2.
3.
Fig-2
3REMOVE THE LED UNIT AND...

Remove 7 screws-A, 2 screws-B and
disconnect the 3 FPC cables of LCD panels.
Grasp the two sides, pull the Main unit upward.
Disconnect the lens motor connector K16S
from the circuit board.
REMOVE THE LENS MOTOR CONNECTOR (See figure 4, 5)5
1.
2.
3.
Fig-4
A
A
A
A
AAA B
B
Cut the wire band and remove the
lens motor lead.
LENS MOTOR CONNECTOR K16SLENS MOTOR CONNECTOR K16S
Fig-5
FPC CABLE REMOVAL
CONNECTOR
FPC
CABLE
CABLE
LOCK
When disconnecting the FPC cable, pull out
the cable lock from the connector and...

MOUNT THE CABINET TOP (See figure-9)
1.
2.
8
Fig-9
MOUNT THE MAIN UNIT (See figure-8)
Mount the main unit with 7 screws-A, 2
screws-B and connect the 3 FPC cables.
Fig-8
9MOUNT THE CABINET FRONT (See figure-8)
10
Remove 4 screws and pull out lens from lens
mounting bracket. Be careful not to drop the
lens when removing it.
REMOVE THE LENS (See figure-6)6
Fig-6
Remove the protective cover on the replacing
lens.
Insert the lens to the lens mounting bracket
and fasten it with the four screws. Use the
screws...

†
¶whŠz
žcmWw:Uq¬Ý›æloXi^M{
èﶦõwKqz©ßÏÉ¿Ä›
ʈqo”‡QtzmWw:U›æl
oXi^M{

èï¶UŠwµ«æá”p`lT“{^•oM”T{



¢U
Y`X昕oM”Tz‡h

¢w
TU
Y`X昕oM”T{

¤
€¯É«»”xz`lT“x‡loM”T{



¢Uݧ
æ
¼tT’‡loMsMT{

Ž•oM”
æ
¼xsMT{
÷	¥Óé´£«»”èï¶

èﶦõS‘|	“
ÇZx
	Í
æ©ßÏÉ¿ÄØ¢Š£z™Ø¢Š£wµ«æá
”›Ž`‡b{
	Í
æ©ßÏÉ¿Äw†± Å›Ëloz	ÍtËj	Í[”
‘OtŽ`‡b{
èﶦõw`Th
	Í
æ©ßÏÉ¿Ä›Žb{¢
$
€	°£


™

w		qpæM‡b{

$

²Ø©ßÏÉ¿Ä›Žb{¢
$€	°£

²Ø©ßÏÉ¿ÄwØwµ«æᔢŠ£›Ž`‡b{

²Ø©ßÏÉ¿Äw†± Å›Ëloz	
²t¾Á”‘
OtŽ`‡b{


µ«æá” 
¢Š£zµ«æá” #
¢Š£t|
-$%ÍÉçw1$
­”Òç¢U	t£›Ž`‡b{
Ý ïâÇ¿Äw†± Å›ËlozT”X	ÍtËj
	Í[‡b{
èï¶Þ”»”w¯É«»” ,4
›Ž`‡b{
¢
$€	°£
èï¶Þ”»”w¯É«»”›Žb{