Sanyo LNS W02/T02 Installation Manual

							PARTS LIST
Following parts are contained in the packing.
·  LENS                
· LENS MOUNTING SCREWS          
· DRIVER                                          
· LIGHT-BLOCK SHEET 
· LENS COVER (UPPER · LOWER )   
NOTES ON LENS INSTALLATION
LCD PROJECTOR LENS
MODEL NO. LNS-W02/T02
LNS-W02K/T02K Series
Lens installation should be performed by the qualified service personnel.
It should be followed by this procedure precisely.
Before attempt to install the lens, confirm the model number (both the LCD
projector and the lens) and use the proper lens.
If you have any questions, contact to the dealers.
Following checks and confirmations should be taken for safety.
Check the following things by the time of the cabinet assembly after the
lens installation.
1. Confirm the lens is securely fixed by 4 screws.
2. Wiring must not be tangled in the gear of the lens motor or the other 
mechanical part.
3. There is no missing part, or no loosing mounting part.
1AA6P1P2289-- (ICSC)
1 piece
6 screws (2 for spare)
1 piece
1 sheet
1 set
LENS REPLACEMENT AND
INSTALLATION PROCEDURE 
						

							LENS REPLACEMENT AND INSTALLATION PROCEDURE
Remove screws A (2 screws).
Pull down the lower lens cover while pushing
the part D, then remove it.
Remove screws B (2 screws).
Remove screws C (2 screws) and remove
upper lens cover.1
5Perform the steps tofor lens replacement and installation.
1
1.
2.
A
Fig-1
Fig-3
lIN CASE OF MODEL WITHOUT LENS
Remove 2 screws and pull down the plate.
2
3.
4.
UPPER LENS COVER
LOWER LENS COVER
C
B
D
D
COVER PLATE
REMOVE THE LENS COVER.
(At the step , insert the light-block sheet in the same
position as the removed cover plate has been placed.
Two screws are not used.)
Use the light-block sheet included with lens.5
REMOVE THE COVER PLATE OF THE LENS COVER. (See figure-3)
Set the light-block
sheet, so that the
large rounder side
is set over the lens.
SCREWS
LIGHT-BLOCK SHEET
Fig-2
LENS COVER
Remove 4 screws of the lens cover and 
remove the lens cover.
First, set the lens at the center position with
lens shift button.
First check the shape of cabinet.
In case figure-1 cabinet.
In case figure-2 cabinet. 
						

							LENS MOTOR LEAD
CONNECTOR “ K16B”
(D)
(D)(D)
(D)
C
LENS MOTOR
kFigure shown inside of the cabinet.
REMOVE THE LENS. (See figure-4)
1. Remove the connector “K16B” of the
circuit board.
2. Loosen the A, B, C wire holder and
remove the lens motor lead.
3. Remove screws D (4 screws) which
fastens the lens and remove the lens. lIN CASE OF MODEL WITH LENS
B
ATTACHED DRIVER
Fig-5
LENS MOUNTING BRACKET
LENS MOTOR LEAD
CONNECTOR “K16B”
(D)
(D)(D)
(D)
B
A
LENS MOTORFig-4
This part wiring should
not be tightened.
C
A
INSTALL THE LENS. (See figure-4,5)3
1. Remove protective caps (front 
and back ) on the lens.
2. Mount the lens at the lens
mounting bracket with screws
(4 screws) included with the
lens. Use the driver included
with the lens to fasten the
screws . (After using, save it for
latter use.)  (See figure-5)
3. Connect the lens motor lead to
the connector “K16B” of the 
circuit board. (See figure-4)
4. Fasten the lens motor lead at
the A, B, C points with wire
holder.
(See figure-4) 
						

							4INSTALL THE LIGHT-BLOCK SHEET.
Fig-6
LIGHT-BLOCK SHEET
(See figure-6)
Install the light-block sheet around the lens
as shown in the illustration.
(Use the sheet included with the lens.)
MOUNT THE LENS COVER. (See figure-7)
5
When in install the both upper and lower lens 
covers, put the light-block sheet through the
lens and install the sheet so that it  should be
placed in the guide slot of the lens cover. (See
figure-8) If the installation of the light-block
sheet is incorrect, there will be the space
between lens and the lens cover, so that it will
be the cause of leakage of light or the dust
entering at the main cabinet.
1.Insert the upper part lens cover and fix them 
with screws A (4 screws).
Fig-7
UPPER LENS COVER
LOWER LENS COVER
A
A
B
LIGHT-BLOCK SHEET
Insert into the slot.
Set the light-block sheet,
so that the large rounder
side is set over the lens.
Fig-8
gRemoved lens cover in figure-2 is not   
used, keep the cover for possible re-
use when current lens is used.
2.Insert the lower part lens cover and fix them 
with screws B (2 screws).