Sanyo Pdg Dwl100 Projector User Manual

							Multimedia Projector
MODEL PDG-DWL100
Owner's Manual 
						

							English
1
English
Table of Contents
Table of Contents
Usage Notice
Precautions ............................................................2
Introduction
Product Features  ...................................................5
Package Overview .................................................6
Product Overview  ..................................................7
Projector  .............................................................7
Connection Ports ................................................8
Control Panel ......................................................8
Remote Control ...................................................9
Remote Control Battery Installation  ..................12
Remote Control Operating Range  ....................12
Installation
Connecting the Projector .....................................13
Connect to Computer/Notebook  .......................13
Connect to Video  ..............................................14
Powering On/Off the Projector .............................15
Powering On the Projector ................................15
Powering Off the Projector ................................16
Warning Indicator  ..............................................17
Adjusting the Projected Image  .............................18
Adjusting the Height of Projector Image  ...........18
Adjusting the Projector Focus ...........................19
Adjusting Projection Image Size  .......................19
User Controls
On Screen Display ...............................................20
How to operate  .................................................20
Image(PC Mode)  ..............................................21
Image(Video Mode) ..........................................23
Screen  ..............................................................25
Setting ...............................................................27
Setting/Network  ................................................30
Language ..........................................................31
Information  ........................................................31
Controlling the Projector From Web  ....................32
Configuring the Network Setting .......................32
Home Page .......................................................35
Control Panel Page ...........................................36
Network Setting Page  .......................................37
Security Setting Page  .......................................38
Alert Setting Page .............................................39
Logout Page  .....................................................40
Appendices
Troubleshooting ...................................................41
Replacing the lamp ..............................................46
Cleaning the Air Filters  ........................................48
Specifications.......................................................49
Computer Compatibility (Analog) .........................50
Computer Compatibility (Digital-HDMI)................51
Configurations of Terminals  .................................53
Terminal : Analog RGB (Mini D-sub 15 pin) ......53
Terminal : Mini DIN 8-pin  ..................................53
Regulation & Safety Notices ................................54
Serial Control Interface  ........................................56
Operation  ..........................................................56
Functional Execution Command .......................57
Status Read Command  ....................................58
Use of Telnet ........................................................59
PJLink Notice  .......................................................60
Dimensions  ..........................................................61
Table of Contents 
						

							2
English
Usage Notice
Precautions
 
Follow all warnings, precautions and maintenance as recom-
mended in this user’s guide to maximize the life of your unit.
■ Warning-This apparatus must be earthed.
■ Warning-Do not look into the projector’s lens when the 
lamp is on.  The bright light may hurt your eyes.
■ Warning-To reduce the risk of fire or electric shock, do not 
expose this projector to rain or moisture.
■ Warning-Please do not open or disassemble the projector 
as this may cause electric shock.
■ Warning-When replacing the lamp, please allow unit to 
cool down, and follow all replacement instruc-
tions..
■ Warning-This projector will detect the life of the lamp 
itself.  Please be sure to change the lamp when it 
shows warning messages.
■ Warning-Reset the “Lamp Counter Reset” function from 
the on-screen display “Setting” menu after re-
placing the lamp module (refer to page 29).
■ Warning-When switching the projector off, please ensure 
the cooling cycle has been completed before 
disconnecting power. Allow 120 seconds for the 
projector to cool down.
■ Warning-Do not use lens cap when projector is powered 
on.
■ Warning-Turn on the projector first and then the signal 
sources.
■ Warning-When the lamp reaches the end of its life, it will 
burn out and may make a loud popping sound. 
If this happens, the projector will not turn back 
on until the lamp module has been replaced. To 
replace the lamp, follow the procedures listed 
under “Replacing the Lamp”. 
						

							English
3
English
Usage Notice
■ Warning-Allowing the proper amount of space on the 
top, sides, and rear of the projector cabinet is 
critical for proper air circulation and cooling of 
the unit. The dimensions shown here indicate the 
minimum space required. If the projector is to be 
built into a compartment or similarly enclosed, 
these minimum distances must be maintained.
1.5 (50 cm)
1.5 (50 cm) 1.5 (50 cm) 3 (1 m)
SIDE and TOP
REAR
■ Warning-Avoid positioning the projector as described 
below when installing.
Do not roll the projector more than 9 degrees 
from side to side.
Do not pitch the projector more than 15 degrees 
from above and below.
Do not point the projector up to project an im-
age.
Do not point the projector down to project an 
image.
Do not put the projector on either side to project 
an image. 
						

							4
English
Usage Notice
  Do:
■   Turn off the product before cleaning.
■   Use a soft cloth moistened with mild detergent to clean the 
display housing.
■   Disconnect the power plug from AC outlet if the product is not 
being used for a long period of time.
  Do not:
■   Block the slots and openings on the unit provided for ventila-
tion.
■   Use abrasive cleaners, waxes or solvents to clean the unit.
■   Use under the following conditions:
-   Extremely heat, cold or humidity.
-   In areas susceptible to excessive dust and dirt.
-   Near any appliance generating a strong magnetic field.
-   In direct sunlight.  
						

							English
5
English
Introduction
Product Features
 
This product is a WXGA single chip 0.65” DLP® projector. 
Outstanding features include:
	■  True WXGA, 1280 x 800 addressable pixels
 ■ Single chip DLP® technology
 ■  NTSC3.58/NTSC4.43/PAL(B/D/G/H/I/M/N)/
SECAM (B/D/G/K/K1/L) and SDTV(480i/576i), 
EDTV(480p/576p), HDTV(720p/1080i/1080p) compat-
ible
 ■   Multi-Auto functions: Auto detection, Auto image and 
Auto saving the adjustments
 ■ Full function remote control
 ■ User friendly multilingual on screen display 
 ■   Advanced digital keystone correction and high quality 
full screen image re-scaling
 ■   Built-in mono 8-Watt speaker.
 ■  UXGA, SXGA+, SXGA  compression and VGA, SVGA 
re-sizing
 ■ Macintosh compatible
Introduction 
						

							6
English
Introduction
Power Cable VGA Cable
Wireless Remote ControlProjector with lens cap
Package Overview
This projector comes with all the items shown below. Check to 
make sure your unit is complete. Contact your dealer immedi-
ately if anything is missing.
	Due to the differ-ence in applications for each country, some regions may have dif-ferent accessories.
Note
Documentation: 
	CD-ROM User’s Manual
	Quick Reference Guide
CableFactory code
AC Power Cable (for U.S.A.)42.00105G011
AC Power Cable (for Continental Europe)42.00120G011
AC Power Cable (for UK)42.00110G011
VGA Cable42.00200G005
2 x AAA Batteries 
						

							English
7
English
Introduction
1. Control Panel
2. Remote Sensor
3. Focus Ring
4. Ventilation (outlet)
5. Lens
6.  Lens Cap (with String)
7. Ventilation (inlet)
8. Speaker
Projector
Product Overview
1
2
3
7
5
4
4
6
4
8
7
7
7
Air Flow 
						

							8
English
Introduction
Connection Ports
SERVICEPORTCOMPUTER IN 1
COMPONENT IN 1( VARIABLE )AUDIO OUTMONITOR OUTS-VIDEO INVIDEO INAUDIO IN
COMPUTER IN 2
COMPONENT IN 2
12345
1013
1.  SERVICE Port
2. HDMI Port
3. S-VIDEO IN Connector
4. VIDEO IN Connector
5.   MONITOR OUT Con-
nector
6.   COMPUTER IN 2/
COMPONENT 2 Con-
nector
789
1112
7.   COMPUTER IN 1/
COMPONENT 1 Con-
nector
8. Network Port
9. AUDIO IN Jack
10. AC IN
11. AUDIO OUT Jack
12. KensingtonTM Lock Port
13. Speaker
Control Panel
123
4
5
7
8
6
1. TEMP LED
2. LAMP LED
3. POWER LED
4. INPUT Button
5.   ON/STAND-BY Button
6.   Four Directional Select 
Keys
7. ENTER Button
8. MENU Button
6 
						

							English
9
English
Introduction
Remote Control
1Infrared trans-
mitter
Sends signals to the projector.
2Infrared indica-
tor
Signals indicator for sending.
3ON/STAND-
BY
Refer to the “Power On/Off the Pro-
jector” section. (See pages 15~16)
4ENTERConfirm your section of items in sub 
menu operation.
2
3
5
15
7
9
11
16
4
17
18
19
20
8
6
12
13
21
22
23
24
10
14
1