Sanyo Pid 42ae1 Instruction Manual

INSTRUCTION MANUALPID- 42AE1
PID- 42AS1
LCD Monitor
Please read this Instruction book before using your LCD monitor. We wish you many hours of pleasure from your new LCD monitor.
 

2

TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . .2
SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . .3
Installation and Use  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .3
SERVICING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Servicing   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .4
Federal Communications Commission Notice   .  .  .  ....

3

CAUTION: Please read and retain for your safety. This unit has been designed and manufactured to assure your personal safety, but improper use can result in potential electric shock or fire hazards. In order not to defeat the safeguards incorporated in this monitor observe the 
following basic rules for its installation, use and servicing .
Installation and Use
Do not allow anything to rest on the power 
cord  . Do not locate this LCD monitor where the cord will be damaged by people walking on it.
Do...

4

Servicing
Your monitor is fully transistorised and does not contain any user ser viceable components. 
You must not remove the rear cover of the monitor by yourself. The apparatus is working with high voltages and could damage objects or even endanger people. Leave all required repair and ser vice jobs to an authorised ser vice technician. He will exclusively use such spare par ts that are complying with the same safety standards as applicable to the original par ts. The use of original spare par ts...



Federal Communications Commission Notice
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC 
Rules . These limits are designed to provide reasonable protection against harmful interference when the equipment is operated 
in a commercial environment . This equipment generates, uses, and can radiate radio frequency energy and, if not installed 
and used in accordance with the instruction manual, may cause harmful interference...

6

AC Power Cord Requirement
The AC Power Cord supplied with this LCD monitor meets the requirement for use in the country in which you  
purchase it  . 
AC Power Cord for the United States and Canada:
AC Power Cord used in the United States and Canada is listed by the Under writers Laboratories (UL) and certified  
by the Canadian Standard Association (CSA)  .
AC Power Cord has a grounding-type AC line plug. This is a safety feature to make sure that the plug will fit into the power outlet.  
Do not...

7

Installation Notice
1.  The LCD monitor can be installated by the following two ways:
2.   The product should be mounted to wall only as recommended by the manufacturer  .
3.  The installation of the bracket must be done by a qualified professional.
  ● Installing the bracket by unqualified personnel may result in injury.
  ● Always use the mounting device specified by a qualified professional.
Note:
For use only with UL Listed Wall Mount Bracket.
SERVICING
Screw holes for installing
Screw holes for...

8

Step: 1 Mains Connection
■  Connect the display unit to VGA, BNC and Scart con-
nector as required.
1.   Connect the in-line power connector to the Mains Inlet as shown 
above  .
2.  Connect the power cord of the LCD monitor to a suitable wall outlet  . 
✐  As this product does not have a mains On/Off switch, please 
ensure your mains plug is easily accessible  .
✐  The LCD monitor is prepared for a mains voltage AC100 ~ 240V, 
50Hz/60Hz  . To completely switch off the mains, or when the 
display...

9

InputTo switch input source from AV1, RGB, AV2, AV3, PC, DVI or Network mode .
StandbyTo switch the monitor on and off  . Also see page 10 .
MenuTo enter and exit the main menu, and sub menu  .
WideTo select the screen mode Full, Full All, Zoom 16:9, Title in 16:9, Zoom 14:9, Title in 14:9,  Normal or Natural wide .
Refer to page 14  .
RecallTo display input selection information and the Time 
set .
You can also select colour systems in AV1/AV3 mode as follows: AUTO í PAL í SECAM í NTSC í NTSC4.43 í...

10

INSTALLATION
Controls and Menus
å
ç
å The LCD display has a Standby light to show there is power.
Switching into/from standby mode
The Standby mode is used for switching the LCD monitor off for short 
periods of time . In standby mode the monitor is switched off but is still 
receiving mains power  .
●   To turn the monitor into standby mode, press the 4 button .  
The blue power indicator illuminates more brightly  .
●  
To turn the monitor ON from standby mode, press the 4 button 
again  .
If you...