Sanyo Plc Xf47 Projector User Manual

							
61

Maintenance and Care
The WARNING indicators show the state of the function which protects the projector. Check the state of the 
WARNING indicators and the READY indicator to take proper maintenance. 
Warning Indicators
The projector is shut down and the WARNING TEMP. 
indicator is blinking red.
When the temperature inside the projector reaches a 
certain level, the projector will be automatically shut down 
to protect the inside of the projector. The LAMP indicator 
turns red and the WARNING TEMP indicator blinks while 
the projector is being cooled down. When the projector has 
cooled down enough (to its normal operating temperature), 
it can be turned on again by pressing the ON/STAND-BY 
button.
✔Note:
	•	 The	WARNING	 TEMP.	indicator	continues	to	blink	even	after	the	
temperature	inside	the	projector	returns	to	normal.	 When	the	
projector	is	turned	on	again,	the	 WARNING	TEMP.	indicator	stops	
blinking.	
Then check the matters below:
–   Did you provide appropriate space for the projector to be 
ventilated? Check the installing condition to see if the air 
vents of the projector are not blocked.
–   Has the projector been installed near an Air-Conditioning/ 
Heating Duct or Vent? Move the installation of the 
projector away from the duct or vent.
–   Is the filter clean? Clean the filter.
CAUTION
DO NOT LEAVE THE PROJECTOR WITH THE 
AC POWER CORD CONNECTED UNDER AN 
ABNORMAL CONDITION. IT MAY RESULT IN FIRE 
OR ELECTRIC SHOCK.
Indicators
Indicators
READY
WARNING TEMP  .
blinking red
Maintenance and Care
READY
The projector is shut down; and the LAMP indicator is 
lighting and other indicators are blinking.
When the projector detects an abnormal condition, it 
will be automatically shut down to protect the inside of 
the projector and the LAMP indicator lights on and other 
indicators blink. In this case, unplug the AC power cord and 
plug it, and then turn on the projector once again to verify 
operation. If the projector cannot be turned on and these 
indicators are still lighting and blinking, unplug the AC power 
cord and contact the service station.
LAMP indicator lights on 
and other indicators blink . 
						

							
6

Troubleshooting
Before calling your dealer or service center for assistance, check the items below once again.
1. Make sure you have properly connected the projector to peripheral equipment as described \
on pages 20–21.
2.  Check the cable connection. Make sure that all computers, video equipment, and power cords are properly 
connected.
3.  Make sure that all power is switched on.
4.  If the projector still does not produce an image, restart your computer.
5.  If an image still does not appear, disconnect the projector from your computer and check your computer 
monitor’s display. A problem may be noticed with your graphics controller rather than with the projector. 
(When you reconnect the projector, be sure to turn the computer and monitor off before you turn on the 
projector. Turn on equipment in the order of the projector and computer.)
6.  If a problem still persists, check the following solutions.
Appendix
Problem:Solutions
No power  .– Plug the power cord of the projector into the AC outlet.
– Turn the MAIN ON/OFF switch to ON.
– Press the ON/STAND-BY Button to ON.
– Make sure the READY Indicator lights.
 –  Check the WARNING TEMP. and the READY indicator. If both the WARNING TEMP. and 
the READY indicator flashes, a projector cannot be turned on.
    (See "TURNING ON/OFF THE PROJECTOR" section on pages 23-24.)
– Check the projection lamp.  (Refer to page 57.)
Image is out of focus .– Adjust focus of the projector.
– Check Projection Lens to see if it needs cleaning.
 ✔Note:  Moving a projector from a cool temperature location to a warm temperature 
location may result in moisture condensation on Projection Lens.  In such cases, 
leave the projector OFF and wait until condensation evaporates.
Picture is Left/Right 
reversed .– Check the Ceiling / Rear function.  (See page 43.)
Picture is Top/Bottom 
reversed .– Check the Ceiling function.  (See page 43)
Some displays are not 
seen during Operation .– Check the Display function. (See “SETTING” section on page 47.)
No image .– Check the connection between your computer or video equipment and a projector.
– It takes about 20 seconds to display an image after turning on the projector.
– See if the selected system is corresponding with your computer or video equipment.
– Make sure the temperature is not out of Operating Temperature (41˚F–95˚F [5˚C–35˚C]).
The initial display is not 
shown .– Make sure “Off ” or “Countdown Off” are not chosen at Display function.
   (See “SETTING” section on page 47)
The initial display is not 
same with the default 
one .– Make sure “User” or “Off” are not chosen at Logo select function.
   (See “SETTING” section on page 48)
	
appears on the screen
–  The end of lamp life is approaching. Replace the lamp with a new one promptly.  
    (See page 57) 
						

							
6

Picture is not bright 
enough .– Check if “Contrast” or “Brightness” are adjusted properly. (See page 44) 
–  Check if “Image level” is selected properly. (See pages 37, 41)
–  Check  the Lamp control function. ( See “SETTING” section on page 50)
–   Check the Lamp replace indicator. If it lights, the end of lamp life is approaching. Replace 
the lamp with a new one promptly.  (See page 57)
–   The image is darker when 2 lamp mode is selected, compared with 4 lamp mode. Check 
the lamp mode at SETTING section on page 50. 
The color is strange .– Check the Input signal, color system, video system, or computer system mode.
The image is distorted or 
runs off  .– Check “PC Adjust” menu or “ Screen” menu and adjust them.
Auto PC adjustment 
function does not work.
–  Check the Input signal.  Auto PC Adjustment function can not work when 480p, 575p, 
720p, 480i, 575i, 1035i, or 1080i is selected or when the digital signal is input into DVI 
terminal. (See page 34) 
The setting does not 
remain after turning off 
power  .–  Make sure you selected “Store” after adjusting settings. Some settings can not be stored 
if not registered with “Store”.
Power management 
function does not work .–  Power management function can not work while “Freeze” or “No Show” function is 
running.
Capture function does not 
work .– Check the connection to see if there is signal.
Some menus can not be 
selected .– Each of the Video Input and Computer Input has a limit on selectable menus.
The power is turned off 
automatically  .–  Power management function runs by initial setting.  Check “SETTING” section on page  
51.
you can not operate with 
the side control .–   The side control is not available If the side control is locked at “Key lock” under “Security” 
of SETTING section.  Please check “SETTING” section on page 52.
Indicators blinks or lights .–  Check the status of the projector with referring to “ INDICATORS AND PROJECTOR 
CONDITION” on pages 68-69.
The Remote Control does 
not work .
– Check the batteries.
–  Check if the RC sensor is set properly.(See page 51)
–  Make sure no obstruction is between the projector and remote control.
–  Make sure you are not too far from a projector when using the remote control.
    Maximum operating range is 16.4’ (5m).
–  Make sure that the remote control code conforms to the projector’s code.      
(See “SETTING” section on page 50.)
–   Make sure the reset switch in the compartment lid on back of the remote control is set to 
use position.
–  Unlock the Key lock function for the remote control. (See page 52)
–   Wireless remote control does not work when the remote control cable is connected to the  
projector. (See page 15)
Unable to unlock the Logo 
PIN code lock, Security 
key lock or Security PIN 
code lock . – Contact the dealer where you purchased the projector or the service center.
Forget the Logo PIN code 
or Security PIN code .
 – Contact the dealer where you purchased the projector or the service center.
appears on the screen – 
Your operation is invalid. Operate correctly.
Appendix 
						

							
64

WARNING: 
High voltages are used to operate this projector . Do not attempt to open the cabinet .
If problems still persist after following all operating instructions, contact the dealer where you purchased the projector 
or  the  service  center.  Specify  the  model  number  and  explain  about  the  problem. We  will  advise  you  how  to  obtain 
service.
This  symbol  on  the  nameplate  means  the  product  is  Listed  by  Under writers 
Laboratories  Inc.  It  is  designed  and  manufactured  to  meet  rigid  U.L.  safety 
standards against risk of fire, casualty, and electrical hazards.
The CE Mark is a Directive conformity mark of the European Community (EC).
Pixelworks ICs used.
Appendix 
						

							
65

Menu Tree
InputRGB (PC analog)Go to System (1)Input 1
Y, Pb/Cb,Pr/Cr
Computer Input/Video Input
RGB (Scart)
RGB (PC digital)
RGB (AV HDCP)
Network
RGBGo to System (1)
Go to System (3)
Go to System (2)Video
S-video
Input 2
Go to System (1)
InputH-sync freq.V-sync freq.
PIN code lock
Information
Key lock
ScreenLanguageLamp mode
Power management
Security
Remote control code
Quit
0–630–63
Off/On/Film
Image AdjustContrastBrightnessColor ✽Tint ✽
RedGreenBlue
Sharpness
ResetStore
Gamma
Progressive ✽
0–630–630–63
0–31 0–15
Image 1Yes / No
Quit
Off/OnNoise reduction ✽
0–630–63
✔Note:
 •	 The	Menu	display	varies	depending	on	the	input	signal.
InformationImage Adjust
✽Displayed	only	in	Video	Input
HighMidLow
XLow
Adj.
Color temp.
Appendix
Colormanagement
Auto picture controlOff/L1/L2
HighMidLow
Color temp.
OffsetRed/Green/Blue
Image 10
Color
Gamma
ListColor M.
Menu
MidLow
Color M.
All DelMenu
Lamp control
Go to System (2) 
						

							
66

Computer Input
System (1)Mode 1
Mode 2
Image SelectStandard
Real
Image 1
Image 10
ScreenNormal
True
Wide
Full screen
Digital zoom +
Digital zoom -
PC AdjustAuto PC adj.
Fine sync.
Total dots
Position H
Position V
Current mode
Clamp
Display area - H
Display area - V
Reset
Mode free
Store
Quit
0–31
Yes/No
Mode 1
Mode 10
Quit
✽ System displayed in the System Menu varies depending on the input signal.
✔Note:
 •	 The	Menu	display	varies	depending	on	the	input	signal.
SVGA 1
SVGA 2
SVGA 3
Rear
Keystone
CeilingResetStore
On/OffOn/Off
CustomH & VScale
Position
H / VOn/OffH / VCommonReset
Video Input
System (2)Auto
PAL
SECAM
NTSC
NTSC 4.43
PAL-M
PAL-N
System (3)Auto
1080i
1035i
720p
575p
480p
575i
480i
Image SelectStandard
Cinema
Image 1
Image 10
ScreenNormal
Wide
Rear
Keystone
CeilingResetStore
On/OffOn/Off
CustomH & VScale
Position
H / VOn/OffH / VCommonReset
Reset
Reset
Appendix
Quit
Quit 
						

							
67

Computer Input/Video Input
SettingLanguage
Fan control
Quit
Position/Simple Menu
Blue/User/Black
Logo select
Capture
Logo PIN code lock
Quit
Auto/Normal/Eco
12 languages provided.
Menu
Logo
Lamp control
Both/Front/Back
Normal/Max
Power management
Background
On/Off
Logo PIN code change
Quit
RC sensor
Ready
Off
Shut down
1–30 Min.
Quit
On/OffOn start
Key lockSecurityOff
Projector
Remote Control
PIN code lockOff/On1/On2
PIN code change
Used timeFilter counter
Yes/NoFactory default
Quit
On/Countdown Off/OffDisplay
User/Default/Off
Yes/No
Code 1Remote Control
Code 8
Quit
Off/100H/300H/500H
ResetYes/No
Quit
8 test patterns providedTest patternQuit
Lamp counterHour(s)
Quit
ResetYes/No
Appendix
Quit
Lamp mode4-Lamp mode/ 2-Lamp mode
Quit
Projector ID 
						

							
6

Indicators and Projector Condition
Check the indicators for the projector condition.  
Indicators
Projector ConditionLAMP
red
READY
green
WARNINGTEMP.
red
LAMPREPLACE
orange
The projector is off. (The main switch is OFF position  or the AC power 
cord is unplugged.)
The projector is in stand-by mode. Press the ON/STAND-BY button to 
turn on the projector.
The projector is operating normally.
The projector is preparing for stand-by or the projection lamp is 
being cooled down. The projector cannot be turned on until cooling is 
completed and the READY indicator lights green.
The projector is in the Power management mode.
The projector is operating normally .
• • • on
• • • off• • •  
blinking at the normal rate       
(approx. 1 second ON,         
1 second OFF)• • • dim
• • •  blinking slow           
(approx. 2 seconds ON, 
2 seconds OFF)
• • • blinking fast              
(approx. 0.5 seconds ON,  
0.5 seconds OFF)
✽
✽
✽
✽
Appendix
✽When the projection lamp reaches its end of life, the LAMP REPLACE indicator lights orange.  
When this lights orange, replace the projection lamp a new one promptly. Reset the lamp 
counter after replacing the lamp (p.57) 
						

							
69

Indicators
Projector ConditionLAMP
red
READY
green
WARNINGTEMP.
red
LAMPREPLACE
orange
The temperature inside the projector is elevated close to the 
abnormally high level.
The temperature inside the projector is abnormally high. The projector 
cannot be turned on. When the projector is cooled down enough and 
the temperature returns to normal, the READY indicator lights green 
and the projector can be turned on. (The WARNING TEMP. indicator 
keeps blinking.) Check and clean the filter.
The projector has been cooled down enough and the temperature 
returns to normal. When turning on the projector, the WARNING TEMP. 
indicator stops blinking. Check and clean the filter.
Any  of  4  lamps  becomes  out,  Lamp  Mode  is  changed  over  from  4  lamps  to  2 
lamps.  And when any of 2 lamps are out, a projector operates with 1 lamp.
The lamp has been used overtime. Replace the lamp immediately 
and then reset the lamp counter. The indicator will be turned off after 
resetting the counter.
The projector detects an abnormal condition and cannot be turned on. 
Unplug the AC power cord and plug it again to turn on the projector. If 
the projector is turned off again, unplug the AC power cord and contact 
the dealer or the service center. Do not leave the projector on. It may 
cause an electric shock or a fire hazard.
✽
Appendix
The projector is detecting abnormal condition .
✽
✽
✽
✽
✽✽✽ 
						

							
70

Compatible Computer Specifications
Basically this projector can accept the signal from all computers with the V- and H-Frequency mentioned below 
and less than 230 MHz of Dot Clock.
 PC Adjustment is limited when selecting these modes.
Appendix
✽True cannot be selected when UXGA2, UXGA3, UXGA4 and UXGA5 are selected (p.38)
ON-SCREEN DISPLA yRESOLUTION H-Freq .(kHz)V-Freq .(Hz)
VGA 1640x48031.470 59.880 
VGA 2720x40031.470 70.090 
VGA 3640x40031.470 70.090 
VGA 4640x48037.860 74.380 
VGA 5640x48037.860 72.810 
VGA 6640x48037.500 75.000 
VGA 7640x48043.269 85.000 
MAC LC13640x48034.970 66.600 
MAC 13640x48035.000 66.670 
480p640x48031.470 59.880 
575p768x57531.250 50.000 
575i768x576 (Interlace)15.625 50.000 
480i640x480 (Interlace)15.734 60.000 
SVGA 1800x60035.156 56.250 
SVGA 2800x60037.880 60.320 
SVGA 3800x60046.875 75.000 
SVGA 4800x60053.674 85.060 
SVGA 5800x60048.080 72.190 
SVGA 6800x60037.900 61.030 
SVGA 7800x60034.500 55.380 
SVGA 8800x60038.000 60.510 
SVGA 9800x60038.600 60.310 
SVGA 10800x60032.700 51.090 
SVGA 11800x60038.000 60.510 
MAC 16832x62449.720 74.550 
XGA 11024x76848.360 60.000 
XGA 21024x76868.677 84.997 
XGA 31024x76860.023 75.030 
XGA 41024x76856.476 70.070 
XGA 51024x76860.310 74.920 
XGA 61024x76848.500 60.020 
XGA 71024x76844.000 54.580 
XGA 81024x76863.480 79.350 
XGA 91024x768 (Interlace)36.000 87.170 
XGA 101024x76862.040 77.070 
XGA 111024x76861.000 75.700 
XGA 121024x768 (Interlace)35.522 86.960 
XGA 131024x76846.900 58.200 
XGA 141024x76847.000 58.300 
XGA 151024x76858.030 72.000 
MAC 191024x76860.240 75.080 
SXGA 11152x86464.200 70.400 
SXGA 21280x102462.500 58.600 
SXGA 31280x102463.900 60.000 
SXGA 41280x102463.340 59.980 
SXGA 51280x102463.740 60.010 
ON-SCREEN 
DISPLA yRESOLUTION H-Freq .(kHz)V-Freq .(Hz)
SXGA 61280x102471.690 67.190 
SXGA 71280x102481.130 76.107 
SXGA 81280x102463.980 60.020 
SXGA 91280x102479.976 75.025 
SXGA 101280x96060.000 60.000 
SXGA 111152x90061.200 65.200 
SXGA 121152x90071.400 75.600 
SXGA 131280x1024 (Interlace)50.000 86.000 
SXGA 141280x1024 (Interlace)50.000 94.000 
SXGA 151280x102463.370 60.010 
SXGA 161280x102476.970 72.000 
SXGA 171152x90061.850 66.000 
SXGA 181280x1024 (Interlace)46.430 86.700 
SXGA 191280x102463.790 60.180 
SXGA 201280x102491.146 85.024 
SXGA+ 11400x105063.970 60.190 
SXGA+ 21400x105065.350 60.120 
SXGA+ 31400x105065.120 59.900 
SXGA+ 41400x105064.03060.010
SXGA+ 51400x105062.50058.600
MAC 211152x87068.680 75.060 
MAC1280x96075.000 75.080 
MAC1280x102480.000 75.080 
WXGA 11366x76848.360 60.000 
WXGA 21360x76847.700 60.000 
WXGA 31376x76848.360 60.000 
WXGA 41360x76856.160 72.000 
WXGA 61280x76847.776 59.870 
WXGA 71280x76860.289 74.893 
WXGA 81280x76868.633 84.837 
WXGA 91280x80049.600 60.050 
WXGA 101280x80041.200 50.000 
UXGA 11600x120075.000 60.000 
UXGA 21600x120081.250 65.000 
UXGA 31600x120087.500 70.000 
UXGA 41600x120093.750 75.000 
UXGA 51600x1200106.250 85.000 
720p1280x72045.000 60.000 
720p1280x72037.49550.000 
1035i1920x1035 (Interlace)33.750 60.000 
1080i
1920x1080 (Interlace)33.750 60.000 
1920x1080 (Interlace)28.125 50.000 
✽
✽
✽
✽