Sharp PNV602 Lcd Monitor User Manual

							PN-V602
LCD MONITOR
OPERATION MANUAL 
						

							IMPORTANT:
To aid reporting in case of loss or theft, please record the 
product’s model and serial numbers in the space provided. 
The numbers are located in the rear of the product.
Model No.:
Serial No.:U.S.A. ONLY
FOR CUSTOMERS IN U.K.IMPORTANT
The wires in this mains lead are coloured in accordance with the followi\
ng code: GREEN-AND-YELLOW: Earth
BLUE:  Neutral
BROWN:  Live
As the colours of the wires in the mains lead of this apparatus may not \
correspond with the coloured markings identifying the 
terminals in your plug proceed as follows: •	The	wire	which 	is	coloured	GREEN-AND-YELLOW	must	be	connected	to	the	terminal	in	the	plug	which	is	marked	by	the	
letter E or by the safety earth 
	or	coloured	green	or	green-and-yellow.
•	The	wire	which 	is	coloured	BLUE	must	be	connected	to	the	terminal	which	is	marked	with	the	letter	 N or coloured black.
•	The	wire	which 	is	coloured	BROWN	must	be	connected	to	the	terminal	which	is	marked	with	the	letter	 L or coloured red.
Ensure	that	your	equipment	is	connected	correctly.	If	you	are	in	any	doubt	consult	a	qualified	electrician. “WARNING: THIS APPARATUS MUST BE EARTHED.” 
						

							3E
IMPORTANT INFORMATION
WARNING: 	TO	REDUCE	THE	RISK	OF	FIRE	OR	ELECTRIC	SHOCK,	DO	NOT 	EXPOSE	THIS	PRODUCT 	
TO	RAIN	OR	MOISTURE.
RISK	OF	ELECTRIC	
SHOCK
DO	NOT 	OPEN
CAUTION
CAUTION:	 	 TO	REDUCE	 THE	RISK	OF	ELECTRIC	
SHOCK,	DO	NOT 	REMOVE	COVER. 
NO	USER-SERVICEABLE	PARTS	
INSIDE. 
REFER	SERVICING	 TO	QUALIFIED	
SERVICE	PERSONNEL.
The	lightning	flash	with	arrowhead	symbol,	within	
an	equilateral	triangle,	is	intended	to	alert	the	
user to the presence of uninsulated “dangerous 
voltage” within the product’s enclosure that may 
be	of	sufficient	magnitude	to	constitute	a	risk	of	
electric shock to persons.
The exclamation point within a triangle is 
intended to alert the user to the presence of 
important operating and maintenance (servicing) 
instructions in the literature accompanying the 
product.
WARNING: 
FCC	Regulations	state	that	any	unauthorized	changes	or	modifications	to	this	equipment	not	expressly	approved	by	the	
manufacturer	could	void	the	user’s	authority	to	operate	this	equipment.
NOTE:This	equipment	has	been	tested	and	found	to	comply	with	the	limits	for	Class	 A	digital	device,	pursuant	to	Part	15	of	the	
FCC	Rules.	 These	limits	are	designed	to	provide	reasonable	protection	against	harmful	interference	when	the	equipment	
is	operated	in	a	commercial	environment.	 This	equipment	generates,	uses,	and	can	radiate	radio	frequency	energy	and,	if	
not installed and used in accordance with the instruction manual, may ca\
use harmful interference to radio communications. 
Operation	of	this	equipment	in	a	residential	area	is	likely	to	cause	harmful	interference	in	which	case	the	user	will	be	required	
to correct the interference at his own expense.
This	product	utilizes	a	CR	coin	Lithium	battery	which	contains	a	Perchlorate	material.
Special handling for this material may apply, 
California	residents,	See	 www.dtsc.ca.gov/hazardouswaste/perchlorate/  
Others,	consult	local	environmental	officers.
U.S.A. ONLY 
						

							4E
IMPORTANT INFORMATION (Continued)
A. Information on Disposal for Users (private households)
1. In the European Union
Attention:	If	you	want	to	dispose	of	this	equipment,	please	do	not	use	the	ordinary	dustbin!	
Used	electrical	and	electronic	equipment	must	be	treated	separately	and	in	accordance	with	legislation	that	requires	proper	
treatment,	recovery	and	recycling	of	used	electrical	and	electronic	equipment.	
Following	the	implementation	by	member	states,	private	households	within	the	EU	states	may	return	their	used	electrical	and	
electronic	equipment	to	designated	collection	facilities	free	of	charge*.		In	some	countries*	your	local	retailer	may	also	take	
back your old product free of charge if you purchase a similar new one. \
*)	Please	contact	your	local	authority	for	further	details.
If	your	used	electrical	or	electronic	equipment	has	batteries	or	accumulators,	please	dispose	of	these	separately	beforehand	
according	to	local	requirements.
By	disposing	of	this	product	correctly	you	will	help	ensure	that	the	waste	undergoes	the	necessary	treatment,	recovery	and	
recycling and thus prevent potential negative effects on the environment and human health which could otherwise arise du\
e 
to inappropriate waste handling.
2. In other Countries outside the EU
If you wish to discard this product, please contact your local authoriti\
es and ask for the correct method of disposal.  
For	Switzerland:	Used	electrical	or	electronic	equipment	can	be	returned	free	of	charge	to	the	dealer,	even	if	you	don’t	
purchase	a	new	product.	Further	collection	facilities	are	listed	on	the	homepage	of	www.swico.ch	or	www.sens.ch.
B. Information on Disposal for Business Users
1. In the European Union
If the product is used for business purposes and you want to discard it:\
Please	contact	your	SHARP	dealer	who	will	inform	you	about	the	take-back	of	the	product.	 You	might	be	charged	for	the	
costs	arising	from	take-back	and	recycling.	Small	products	(and	small	amounts)	might	be	taken	back	by	your	local	collection	
facilities.
For	Spain:	Please	contact	the	established	collection	system	or	your	local	authority	for	take-back	of	your	used	products.
2. In other Countries outside the EU
If you wish to discard of this product, please contact your local author\
ities and ask for the correct method of disposal. Attention: Your product is marked with this symbol. It means that used electrical an\
d electronic products 
should not be mixed with general household waste. There is a separate collection system for these products.
EU	ONLY
The battery supplied with this product contains traces of Lead.
For	EU:
The	crossed-out	wheeled	bin	implies	that	used	batteries	should	not	be	put	to	the	general	household	
waste!	 There	is	a	separate	collection	system	for	used	batteries,	to	allow	proper	treatment	and	recycling	in	
accordance with legislation. Please contact your local authority for det\
ails on the collection and recycling 
schemes.
For	Switzerland: The used battery is to be returned to the selling point.
For	other	non-EU	countries: Please contact your local authority for correct method of disposal of th\
e used battery.
EU	ONLY
“BATTERY 	DISPOSAL”
THIS	PRODUCT 	CONTAINS	A	LITHIUM	PRIMARY 	(MANGANESS	DIOXIDE)	MEMORY 	BACK-UP	BATTERY 	THAT 	
MUST 	BE	DISPOSED	OF	PROPERLY.	PLEASE	CONTACT 	YOUR	LOCAL 	SHARP	DEALER	OR	 AUTHORIZED	SERVICE	
REPRESENTATIVE	FOR	 ASSISTANCE	IN	DISPOSING	OF	 THIS	BATTERY.
U.S.A.	AND	CANADA 	ONLY 
						

							5E
Thank	you	for	your	purchase	of	a	SHARP	LCD	product.	To	ensure	safety	and	many	years	of	trouble-free	operation	of	your	
product, please read the Safety Precautions carefully before using this \
product.
SAFETY PRECAUTIONS
Electricity	is	used	to	perform	many	useful	functions,	but	it	can	also	cause	personal	injuries	and	property	damage	if	improperly	
handled.	 This	product	has	been	engineered	and	manufactured	with	the	highest	priority	on	safety.	However,	improper	use	can	
result	in	electric	shock	and/or	fire.	In	order	to	prevent	potential	danger,	please	observe	the	following	instructions	when	installing,	
operating	and	cleaning	the	product.	 To	ensure	your	safety	and	prolong	the	service	life	of	your	LCD	product,	please	read	the	
following precautions carefully before using the product.
  1.	 Read 	instructions	—	 All	operating	instructions	must	be	read	and	understood	before	the	product	is	operated.
	 2.	 	 Keep	this	manual	in	a	safe	place	—	 These	safety	and	operating	instructions	must	be	kept	in	a	safe	place	for	future	
reference.
	 3.	 Observe	warnings	—	 All	warnings	on	the	product	and	in	the	instructions	must	be	observed	closely.
	 4.	 Follow	instructions	—	 All	operating	instructions	must	be	followed.
	 5.	 	
Cleaning	—	Unplug	the	power	cord	from	the	 AC	outlet	before	cleaning	the	product.	Use	a	dry	cloth	to	clean	the	product.	Do	
not	use	liquid	cleaners	or	aerosol	cleaners.
	 6.	 	
Attachments	—	Do	not	use	attachments	not	recommended	by	the	manufacturer.	Use	of	inadequate	attachments	can	result	
in accidents.
	 7.	 	 Water	and	moisture	—	Do	not	use	the	product	near	water.	Do	not	install	the	product	in	a	place	where	water	may	splash	onto	
it.	Be	careful	of	equipment	which	drains	water	such	as	an	air-conditioner.
	 8.	 Ventilation	—	 The	vents	and	other	openings	in	the	cabinet	are	designed	for	ventilation.
	 	 	 Do	not	cover	or	block	these	vents	and	openings	since	insufficient	ventilation	can	cause	overheating	and/or	shorten	the	life	
of	the	product.	Do	not	place	the	product	on	a	sofa,	rug	or	other	similar	surface,	since	they	can	block	ventilation	openings.	
Do	not	place	the	product	in	an	enclosed	place	such	as	a	bookcase	or	rack,	unless	proper	ventilation	is	provided	or	the	
manufacturer’s instructions are followed.
	 9.	 	 Power	cord	protection	—	 The	power	cords	must	be	routed	properly	to	prevent	people	from	stepping	on	them	or	objects	from	
resting on them.
	10.	 	
The	LCD	panel	used	in	this	product	is	made	of	glass.	 Therefore,	it	can	break	when	the	product	is	dropped	or	applied	with	
impact.	Be	careful	not	to	be	injured	by	broken	glass	pieces	in	case	the	LCD	panel	breaks.
	11.	 Overloading	—	Do	not	overload	 AC	outlets	or	extension	cords.	Overloading	can	cause	fire	or	electric	shock.
	12.	 	
Entering	of	objects	and	liquids	—	Never	insert	an	object	into	the	product	through	vents	or	openings.	High	voltage	flows	in	
the	product,	and	inserting	an	object	can	cause	electric	shock	and/or	short	internal	parts.
	 	 For	the	same	reason,	do	not	spill	water	or	liquid	on	the	product.
	13.	 	 Servicing	—	Do	not	attempt	to	service	the	product	yourself.	Removing	covers	can	expose	you	to	high	voltage	and	other	
dangerous	conditions.	Request	a	qualified	service	person	to	perform	servicing.
	14.	 	 Repair	—	If	any	of	the	following	conditions	occurs,	unplug	the	power	cord	from	the	 AC	outlet,	and	request	a	qualified	service	
person to perform repairs.  
a.	 When	the	power	cord	or	plug	 is	damaged. 
b.	 When	a	liquid 	was	spilled	on	the	product	or	when	objects	have 	fallen	into	the	product. 
c.	 When	the	product	has	been	exposed	to	rain	or	water. 
d.	 When	the	product	does	not	operate	properly	as	described	in	the	operating	instructions.  
	 	 Do	not	touch	the	controls	other	than	those	described	in	the	operating	instructions.	Improper	adjustment	of	controls	
not	described	in	the	instructions	can	cause	damage,	which	often	requires	extensive	adjustment	work	by	a	qualified	
technician.
	 	 e.	 When	the	product	has	been	dropped	or	damaged.  
	 	 f.	 	 When	the	product	displays	an	abnormal	condition.	 Any	noticeable	abnormality	in	the	product	indicates	that	the	product	
needs servicing.
15.	 	
Replacement	parts	—	In	case	the	product	needs	replacement	parts,	make	sure	that	the	service	person	uses	replacement	
parts	specified	by	the	manufacturer,	or	those	with	the	same	characteristics	and	performance	as	the	original	parts.	Use	of	
unauthorized	parts	can	result	in	fire,	electric	shock	and/or	other	danger.
	16.	 Safety	checks	—	Upon	completion	of	service	or	repair	work,	request	the	service	technician	to	
    perform safety checks to ensure that the product is in proper operating \
condition.
	17.	 	 Wall	mounting	—	When	mounting	the	product	on	a	wall,	be	sure	to	install	the	product	according	to	the	method	
recommended by the manufacturer.
	18.	 	 Heat	sources	—	Keep	the	product	away	from	heat	sources	such	as	radiators,	heaters,	stoves	and	other	heat-generating	
products	(including	amplifiers).
DEAR SHARP CUSTOMER 
						

							6E
SAFETY PRECAUTIONS (Continued)
	19.	 Batteries	—	Incorrect	use	of	batteries	may	cause	the	batteries	to	burst	or	ignite.	A	leaky	battery	may	corrode	the	equipment,
    dirty your hands or spoil your clothing. In order to avoid these problem\
s, make sure to observe the precautions below:
	 	 •	Use	the	specified	batteries	only.
	 	 •		 Install	the	batteries	with	due	attention	to	the	plus	(+)	and	minus	(-)	sides	of	the	batteries	according	to	the	instructions	in	the	
compartment.
	 	 •	Do	not	mix	old	and	new	batteries.
	 	 •	Do	not	mix	batteries	of	different	types.	Voltage	specifications	of	batteries	of	the	same	shape	may	vary.
	 	 •	Replace	an	exhausted	battery	with	a	new	one	promptly.
	 	 •	If	you	will	not	use	the	remote	control	for	a	long	time,	remove	the	batteries.
	 	 •		 If	leaked	battery	fluid	gets	on	your	skin	or	clothing,	rinse	immediately	and	thoroughly.	If	it	gets	into	your	eye,	bathe	your	
eye	well	rather	than	rubbing	and	seek	medical	treatment	immediately.	Leaked	battery	fluid	that	gets	into	your	eye	or	your	
clothing may cause a skin irritation or damage your eye.
	20.	 	 Usage	of	the	monitor	must	not	be	accompanied	by	fatal	risks	or	dangers	that,	could	lead	directly	to	death,	personal	injury,	
severe physical damage or other loss, including nuclear reaction control\
 in nuclear facility, medical life support system, and 
missile launch control in a weapon system.
	21.	 	 Do	not	stay	in	contact	with	the	parts	of	the	product	that	become	hot	for	long	periods	of	time.	Doing	so	may	result	in	  
low-temperature	burns.
WARNING:
This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be 
required	to	take	adequate	counter	measures.
To	maintain	compliance	with	EMC	regulations,	use	shielded	cables	to	connect	to	the	following	terminals:	PC/AV	DVI-D	output	
terminal,	PC/AV	DVI-D	input	terminal,	PC/AV	HDMI	input	terminal,	PC	D-SUB	input	terminal,	PC	RGB	input	terminals,	and	
RS-232C	input/output	terminals.
If	a	monitor	is	not	positioned	in	a	sufficiently	stable	location,	it	can	be	potentially	hazardous	due	to	falling.	Many	injuries,	
particularly to children, can be avoided by taking simple precautions su\
ch as:
•	Using	fixing	devices	like	wall	mount	brackets	recommended	by	the	manufacturer.
•	Only	using	furniture	that	can	safely	support	the	monitor.
•	Ensuring	the	monitor	is	not	overhanging	the	edge	of	the	supporting	furniture.
•		 Not	placing	the	monitor	on	tall	furniture	(for	example,	cupboards	or	bookcases)	without	anchoring	both	the	furniture	and	the	
monitor to a suitable support.
•	Not	standing	the	monitors	on	cloth	or	other	materials	placed	between	the	monitor	and	supporting	furniture.
•	Educating	children	about	the	dangers	of	climbing	on	furniture	to	reach	the	monitor	or	its	controls.	
Especially for child safety
-	Don’t	allow	children	to	climb	on	or	play	with	the	monitor.
-	Don’t	place	the	monitor	on	furniture	that	can	easily	be	used	as	steps,	such	as	a	chest	of	drawers.
-		 Remember	that	children	can	become	excited	while	watching	a	program,	especially	on	a	“larger	than	life”	monitor.	Care	
should be taken to place or install the monitor where it cannot be pushe\
d, pulled over, or knocked down.
-		 Care	should	be	taken	to	route	all	cords	and	cables	connected	to	the	monitor	so	that	they	cannot	be	pulled	or	grabbed	by	
curious children. 
						

							7E
-		The	 TFT	color	LCD	panel	used	in	this	monitor	is	made	with	
the	application	of	high	precision	technology.	However,	there	
may be minute points on the screen where pixels never light 
or are permanently lit. Also, if the screen is viewed from 
an acute angle there may be uneven colors or brightness. 
Please note that these are not malfunctions but common 
phenomena	of	LCDs	and	will	not	affect	the	performance	of	
the monitor.
-		 Do	not	display	a	still	picture	for	a	long	period,	as	this	could	
cause a residual image.
-	Never	rub	or	tap	the	monitor	with	hard	objects.
-		 Please	understand	that	SHARP 	CORPORATION	bears	no	
responsibility for errors made during use by the customer or 
a third party, nor for any other malfunctions or damage to this 
product arising during use, except where indemnity liability is 
recognized	under	law.
-		 This	monitor	and	its	accessories	may	be	upgraded	without	
advance notice.
-		 Do	not	use	the	monitor	where	there	is	a	lot	of	dust,	where	
humidity is high, or where the monitor may come into contact 
with	oil	or	steam,	as	this	could	lead	to	fire.
-		 Ensure	that	the	monitor	does	not	come	into	contact	with	
water	or	other	fluids.	Ensure	that	no	objects	such	as	paper	
clips	or	pins	enter	the	monitor	as	this	could	lead	to	fire	or	
electric shock.
-		 Do	not	place	the	monitor	on	top	of	unstable	objects	or	in	
unsafe	places.	Do	not	allow	the	monitor	to	receive	strong	
shocks	or	to	strongly	vibrate.	Causing	the	monitor	to	fall	or	
topple over may damage it.
-		 Do	not	use	the	monitor	near	heating	equipment	or	in	places	
where there is likelihood of high temperature, as this may 
lead	to	generation	of	excessive	heat	and	outbreak	of	fire.
-		 Do	not	use	the	monitor	in	places	where	it	may	be	exposed	to	
direct sunlight.
-		 If	the	monitor	is	installed	in	a	location	exposed	to	sunlight	
such as next to a window, measures to reduce ultraviolet and 
infrared	radiation	and	temperature	measures	are	required.	
For	details,	consult	your	dealer.
-		 Please	be	sure	to	constantly	remove	dust	and	garbage	that	
has attached to the ventilation opening. If dust collects in the 
ventilation opening, it may lead to excessive heat, outbreak 
of	fire,	or	malfunction.	 
As a standard, clean the inside of the monitor once every 
year. If dust collects inside the monitor, it may lead to 
excessive	heat,	outbreak	of	fire,	or	malfunction.	Please	
request	a	cleaning	of	the	inside	of	the	monitor	from	an	
authorized	SHARP 	servicing	dealer	or	service	center.
-		 Images	cannot	be	rotated	on	this	monitor. 
When	using	in	vertical	orientation,	you	will	need	to	prepare	
appropriately orientated content in advance.
-		 The	 AC	outlet	shall	be	installed	near	the	equipment	and	shall	
be easily accessible.
The Power Cord
-		 Use	only	the	power	cord	supplied	with	the	monitor.
-		 Do	not	damage	the	power	cord	nor	place	heavy	objects	on	
it, stretch it or over bend it. Also, do not add extension cords. 
Damage	to	the	cord	may	result	in	fire	or	electric	shock.
-		 Do	not	use	the	power	cord	with	a	power	tap.  
Adding	an	extension	cord	may	lead	to	fire	as	a	result	of	
overheating. -		
Do	not	remove	or	insert	the	power	plug	with	wet	hands.	
Doing	so	could	result	in	electric	shock.
-	Unplug	the	power	cord	if	it	is	not	used	for	a	long	time.
-		 Do	not	attempt	to	repair	the	power	cord	if	it	is	broken	
or malfunctioning. Refer the servicing to the service 
representative.
Manual Scope
-		Microsoft,	Windows	and	Internet	Explorer	are	registered	
trademarks	of	Microsoft	Corporation.
-		 HDMI,	the	HDMI	Logo	and	High-Definition	Multimedia	
Interface	are	trademarks	or	registered	trademarks	of	HDMI	
Licensing	LLC.
-		 Adobe, 	Acrobat, 	and 	Reader 	are 	either 	registered 	trademarks	
or trademarks of Adobe Systems Incorporated in the United 
States and/or other countries.
-		 This	product	comes	with	RICOH	Bitmap	Fonts	produced	and	
sold	by	RICOH	COMPANY,	LTD.
-		 All	other	brand	and	product	names	are	trademarks	or	
registered trademarks of their respective holders.
-		 Language	of	OSD	menu	used	in	this	manual	is	English	by	
way of example.
-		 Illustrations	in	this	manual	may	not	exactly	represent	the	
actual product or display.
-		 This	manual	assumes	use	in	landscape	orientation,	except	
where	specifically	noted.
-		 This	manual	assumes	that	this	product	will	be	used	with	
the	remote	control	unit	buttons,	except	where	specifically	
noted. Operation by using the buttons on the rear side of the 
product will perform the same functions.
Rear side buttons
Remote control 
unit buttons
	 *		 For	operation	with	the	remote	control	unit,	the	PN-ZR01	
control	kit	(optional)	is	required.	
LED Backlight
●	 The	LED	backlight	in	this	product	has	a	limited	lifetime.
	 *		If	the	screen	gets	dark	or	does	not	turn	on,	it	may	be	
necessary	to	replace	the	LED	backlight.	 This	LED	
backlight is exclusive to this product and must be replaced 
by	an	authorized	Sharp	servicing	dealer	or	service	center.
	 *		 Please	contact	your	local	Sharp	servicing	dealer	or	
service center for assistance.
Fan
●	 The	fan	in	this	product	has	a	limited	lifetime.	
TIPS AND SAFETY INSTRUCTIONS 
						

							8E
MOUNTING PRECAUTIONS
•	 This	product	is	for	use	indoors.
•	 A	mounting	bracket	compliant	 with	VESA	specifications	is	
required.
•	 Since	the	monitor	is	heavy,	consult	your	dealer	before	 installing, removing or moving the monitor.
•	 Mounting	the	monitor	on	the	wall	requires	special	expertise	 and	the	work	must	be	performed	by	an	authorized	SHARP 	
dealer. You should never attempt to perform any of this 
work yourself. Our company will bear no responsibility 
for	accidents	or	injuries	caused	by	improper	mounting	or	
mishandling.
•	 Use	the	monitor	perpendicular 	to	a	level	surface.	If	
necessary,	the	monitor	may	be	tilted	up	to	20	degrees	
upward or downward.
•	 When	mounting	the	monitor	horizontally,	the	optional	fan	 cover	(PN-ZR31)	is	required.	For	details	along	with	the	
horizontal	mounting	conditions,	consult	your	dealer.
•	 This	monitor	should	be	used	at	an	ambient	temperature	 between	32°F	(0°C)	and	104°F	(40°C).
•	 Be	careful	of	high	temperatures	in	the	surrounding	area.  
When	installing	the	monitor	inside	a	housing,	or	if	the	
ambient	temperature	may	be	outside	of	the	range	of	32ºF	
(0ºC)	to	104ºF	(40ºC),	install	a	fan	or	take	other	measures	
to	keep	the	ambient	temperature	within	the	required	range.	
•	 Temperature	condition	may	change	when	using	the	monitor	 together	with	the	optional	equipments	recommended	by	
SHARP.	In	such	cases,	please	check	the	temperature	
condition	specified	by	the	optional	equipments.
•	 Do	not	block	any	ventilation	openings.	If	the	temperature	 inside the monitor rises, this could lead to a malfunction.
•	 Do 	not 	place 	the 	monitor 	on 	a 	device 	which 	generates 	heat. •	 Adhere	to	the	following	when	installing	the	monitor	in	its	
portrait	orientation.	Failing	to	adhere	to	the	following	may	
cause malfunctions. 
-		To	install	in	landscape	orientation,	rotate	the	monitor	90	
degrees to the right.
-	Set	the	MONITOR	on	the	SETUP 	menu	to	PORTRAIT.
(See page 24.)
-		 Be	sure	to	secure	the	power	cord	(supplied)	to	the	cable	
clamp attachment with the supplied cable clamp. Make 
sure that the power cord (supplied) does not supply power 
to the terminal when being secured and do not over bend 
the power cord (supplied).
Cable	clamp
Power cord (Supplied)
Cable	clamp	
attachment
Mounting Precautions (For SHARP dealers and service engineers)
•	 When	installing,	removing	or	moving	the	monitor,	ensure	that	this	is	carried	out	by	at	least	2	people.
•	 Be	sure	to	use	a	wall-mount	bracket	designed	or	designated	for	mounting	the	monitor.
•	 This 	monitor 	is 	designed 	to 	be 	installed 	on 	a 	concrete 	wall 	or 	pillar. 	Reinforced 	work 	might 	be 	necessary 	for 	some 	materials	
such as plaster / thin plastic board / wood before starting installation\
.   
This monitor and bracket must be installed on a wall which can endure at\
 least 4 times or more the weight of the monitor. 
Install by the most suitable method for the material and the structure.
•	 To	attach	a	VESA-compliant	mounting	bracket,	use	M6	screws	that	are	5/16	inch	(8	mm)	to	3/8	inch	(10	mm)	longer	than	 the thickness of the mounting bracket.
•	 When	moving	the	monitor,	be	sure	to	hold	it	with	either	both	handles	or	the	4	corners	on	the	bottom	of	the	unit.	Do	not	hold	 the	LCD	panel.	 This	may	cause	product	damage,	failure,	or	injury.
•	 When	performing	an	installation	where	the	monitor	is	stacked,	please	install	it	such	that	load	is	not	placed	on	the	monitor	 frame.
•	 After	mounting,	please	carefully	ensure	the	monitor	is	secure,	and	not	able	to	come	loose	from	the	wall	or	mount.
•	 Do	not	use	any	screw	holes	other	than	VESA 	holes	for	installation. 
						

							9E
Contents
Supplied Components
If any component should be missing, please contact your dealer.
  Liquid	Crystal	Display	Monitor:	1
  Cable	clamp:	2
  Power	cord:	1
  CD-ROM	(Utility	Disk	for	Windows):	1
  Setup	manual:	1 
 Protection cover: 4
  Handle	screw	(short):	4
  Bezel	sheet	(long/short):	2	each
  Bezel	sheet	attachment	instructions:	1
*	 Sharp	Corporation	holds	authorship	rights	to	the	Utility	Disk	program.	Do	not	reproduce	it	without	permission.
*	 For	environmental	protection!
	 Do	not	dispose	of	batteries	in	household	waste.	Follow	the	disposal	instructions	for	your	area. IMPORTANT INFORMATION 
............................................3
DEAR SHARP CUSTOMER  .............................................. 5
SAFETY PRECAUTIONS  .................................................. 5
TIPS AND SAFETY INSTRUCTIONS  ...............................7
MOUNTING PRECAUTIONS  ............................................8
Mounting Precautions (For SHARP dealers and  
service engineers)  ........................................................... 8
Supplied Components  ..................................................... 9
Part Names  ..................................................................... 10
Connecting Peripheral Equipment  ............................... 12
Multiple monitor connection  ....................................... 13
Preparing the Remote Control Unit  .............................. 15
Installing the batteries  ................................................ 15
Remote control operation range  ................................. 15
Connecting the Power Cord  ......................................... 15
Binding Cables  ............................................................... 16
Removing the Handles  .................................................. 16
Affixing the Protection Covers  .....................................16
Turning Power On/Off  .................................................... 17
Turning on the main power .........................................17
Turning power on/off  .................................................. 17
Disabling	power	on/off	operations  .............................. 17
Basic Operation  ............................................................. 18Remote Control Mode 
 .................................................. 21
Menu Items  ..................................................................... 22
Displaying	the	menu	screen  ....................................... 22
Menu item details  ....................................................... 23
Adjustments	for	PC	screen	display  ............................ 30
Initialization (Reset)/Functional Restriction Setting 
(FUNCTION)  .................................................................... 31
Controlling the Monitor with a PC (RS-232C)  .............. 32
PC	connection  ............................................................ 32
Communication	conditions  ......................................... 32
Communication	procedure  ......................................... 32
Setting	of	the	GAMMA 	user	data ................................ 36
RS-232C	command	table  ........................................... 37
Controlling the Monitor with a PC (LAN)  ..................... 45
Settings to connect to a LAN  ......................................45
Controlling	with	a	PC  .................................................. 47
Troubleshooting  ............................................................. 53
Specifications  ................................................................ 55 
						

							10E
nFront view
1
23 45
6789
The rear buttons if seen  
from the front
1. LCD panel
2. INPUT button
3. MENU button
4. VOL -/Cursor control (
) button
5. VOL +/Cursor control (
) button
6. BRIGHT -/Cursor control (
) button
7. BRIGHT +/Cursor control (
) button
8. Power button
9. Power LED
Part Names
n Rear view
17 15
28
27
26
25 2921
23
16
19 20
18
2224
10
13
14
32
31
30 34
33
12
11
98 7654 32
When the PN-ZB02 
(optional) is attached
10
12
10
 
10. Fan/Fan cover
 
11.  Vents
 
12.  Handles
 
13.  Expansion terminal cover
Additional input/output terminals are available by attaching 
the	PN-ZB02	interface	expansion	board	(optional).
14.  Optional attachment section
This section is used to connect optional hardware for 
function expansion. Offering this attachment location 
is not a guarantee that future compatible hardware 
attachments will be released.
  15.  AC input terminal
 
16.  Main power switch
 
17.  PC/AV HDMI input terminal
 
18.  PC D-sub input terminal
 
19.  Audio input terminal
 
20.  Audio output terminals
 
21.  RS-232C output terminal
 
22.  RS-232C input terminal
 
23.  Optional terminal
This terminal is provided for possible future (optional) 
function expansion. Offering of this terminal is not a 
guarantee that future expanded functionality will be 
provided.
  24.  Control kit terminal
When the PN-ZB02 (optional) is attached
  25.  PC/AV DVI-D input terminal
 
26.  PC/AV DVI-D output terminal
 
27.  LAN terminal
 
28.  External speaker terminals
 
29.  Audio 1 input terminals
 
30.  Audio 2 input terminals
 
31.  PC RGB input terminals
 
32.  AV component input terminals
 
33.  AV video input terminal
 
34.  AV S-video input terminal
Caution
•	 Consult	your	SHARP 	dealer	for	attachment/detachment	of	
optional parts.
•	 Do	not	block	the	fan	cover.
•	 Do	not	open	the	expansion	terminal	cover	by	yourself.  
There are high voltage parts inside the cover which may 
cause an electric shock.