Sharp Projector Pg A10x User Manual

27
Basic Operation
3Press  ,  or  on the
remote control to select the IN-
PUT mode.
•After pressing  once on the projector,
use 
 to select the desired input mode.
Note
•When no signal is received, “NO SIG-
NAL” will be displayed. When a signal
that the projector is not preset to re-
ceive is received, “NOT REG.” will be
displayed.
•The INPUT mode is not displayed
when “OSD Display” is set to “OFF”.
(See page 44.)
About the INPUT mode
4Press  or  on the remote
control to adjust the volume.
Note
•Pressing...

28
Image Projection
', ", \, |
buttons MENU button Power OFF
button
ENTER
button
“Language” menu icon
6Press  on the projector or
 on the remote control, then
press that button again while the
confirmation message is dis-
played, to turn off the projector.
Note
•If you accidentally pressed  or
 and do not want to turn off the
power, wait until the confirmation
message disappears.
•The projector cannot be operated
while a message “Shutting down.
Please wait.” is displayed.
Info
•Do not unplug the...

29
Basic Operation
Keystone Correction (Correcting Trapezoidal Distortion)
Correcting Trapezoidal
Distortion
This function allows for Keystone (On-screen
Trapezoidal Distortion) Correction.
Note
•When the image is projected either from the
top or from the bottom towards the screen
at an angle, the image becomes distorted
trapezoidally.
The function for correcting trapezoidal dis-
tortion is called Keystone Correction.
•The Keystone Correction can be adjusted up
to an angle of approximately ±35 degrees....

30
Menu Items
This list shows the items that can be set in the projector.
 INPUT 1 Mode
Note
•In the “Picture” menu of INPUT 1, “Color”, “Tint” and “Sharp” are only displayed when “Signal Type” is set
to “Component”.
•In the “Picture” menu of INPUT 1, “sRGB” is only displayed when “Signal Type” is set to “RGB”.
•In the “Fine Sync” menu of INPUT 1, “Signal Info” can only be selected when “Signal Type” is set to
“Component”.
+30 −30
+30 −30
+30 −30
+30 −30
+30 −30
+30 −30
+30 −30
Main menu Sub menuMain...

31
Basic Operation
 INPUT 2 / 3 Mode
Main menu
+30 −30
+30 −30
+30 −30
+30 −30
+30 −30
+30 −30
+30 −30
Main menu Sub menu
Contrast
Bright
Color
Tint
Sharp
Red
Blue
Reset
CLR Temp
Gamma
Memory5500 K
6500 K
7500 K
8500 K
9300 K
10500 K
Standard
Presentation
Cinema
Game
Memory 1
Memory OFFMemory 5 Picture
Page 36
Options
Page 44
OSD Display [ON/OFF]
Background
Eco Mode [Eco/Standard]
Sharp
Blue
None
Auto Power Off [ON/OFF]
Menu Position
Password
Anti-TheftCenter
Upper Right
Lower Right
Upper Left
Lower...

32
The menu screens allow you to adjust the image and various projector settings.
You can operate the menus from the remote control using the following procedure.
Using the Menu Screen
Example:“Picture” menu screen for
INPUT 1 (RGB) mode
Menu Selections
(Adjustments)
1Press .
•The “Picture” menu screen for the se-
lected input mode is displayed.
Note
•The on-screen display shown on the
right is displayed when the INPUT 1
(RGB) mode is selected.
2Press 
\ \\ \
\ or 
| || |
| to display the other
menu...

33
Basic Operation
3Press 
' '' '
' or 
" "" "
" to select the item
you want to adjust.
•The selected item is highlighted.
Note
•To display a single adjustment item,
press 
 after selecting the item.
Only the selected adjustment item will
be displayed.
Then if you press ' or ", the follow-
ing item (“Red” after “Bright”) will be
displayed.
•Press 
 to return to the previous
screen.
4Press 
\ \\ \
\ or 
| || |
| to adjust the item
selected.
•The adjustment...

34
Menu Selections
(Settings)
1Press .
•The “Picture” menu screen for the se-
lected input mode is displayed.
Note
•The on-screen display shown on the
right is displayed when INPUT 1 (RGB)
mode is selected.
2Press 
\ \\ \
\ or 
| || |
| to display the other
menu screens.
•The menu icon for the selected menu
screen is highlighted.
Note
•The “Fine Sync” menu is not available
for INPUT 2 or 3.
•For details on the menus, see the tree
charts on pages 30 and 31.
Using the Menu Screen
', ", \, |
buttons...

35
Basic Operation
3Press 
' '' '
' or 
" "" "
" to select the
item you want to set, and then
press 
| || |
| to display the sub menu.
•The selected item is highlighted.
Note
•Press  or \ to return to the pre-
vious screen.
•For some items, press \ or | to se-
lect the icon using “
”.
4Press 
' '' '
' or 
" "" "
" to select the set-
ting of the item displayed in the
sub menu.
5Press .
•The item selected is set.
6Press .
•The...

36
You can adjust the projector’s picture to your preferences using the “Picture” menu. For
operation of the menu screen, see pages 32 to 35.
CLR Temp (Adjusting the
Color Temperature)
Select “CLR Temp” on the “Picture” menu
and the desired color temperature setting.
Description of Color Temperature SettingsAdjusting the Image
Select the item on the “Picture” menu and
adjust the image.
Description of Adjustment Items
Note
•“Color”, “Tint” and “Sharp” are not displayed
when selecting INPUT 1 and setting...