Sharp R-1480 Manual

							29
R-1480
R-1481
R-1482
1. Disconnect the power supply cord, remove the oven
from wall and remove outer case (Refer to procedure of
Removal of Oven from Wall and Outer case Removal.)
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the wire leads from the fan motor and the
chassis support.
5. Remove one (1) screw holding the hood duct to oven
cavity.
6. Release the wire leads from the hole of the hood duct.
7. Lift up the fan motor side of the hood duct.
8. Remove the two (2) screws holding the fan motor to the
hood duct.
9. Remove the fan blade from the fan motor shaft according
the following procedure.
10.Hold the edge of the rotor of the fan motor by using a pair
of groove joint pliers.
CAUTION:
* Make sure that any pieces do not enter the gap
between the rotor and the stator of the fan motor
because the rotor is easily shaven by pliers and
metal pieces may be produced.
* Do not touch the pliers to the coil of the fan motor
because the coil may be cut or injured.
* Do not disfigure the bracket by touching with the
pliers.
11.Remove the fan blade from the shaft of the fan motor by
pulling and rotating the fan blade with your hand.
12. Now, the fan blade will be free.
CAUTION:
* Do not reuse the removed fan blade because the
hole (for shaft) may  be larger  than normal.
13.Now, the fan motor is free.Rear View
Side View 3. Discharge high voltage capacitor.
4. Remove  two (2) unit mounting screws.
5. Remove the hood duct. (Refer to the procedure of 
HOOD FAN MOTOR, HOOD DUCT AND OVEN LAMP
SOCKET REMOVAL.
6. Straighten the tab holding the thermal cut-out to the top
plate of the oven cavity.
7 . Release the thermal cut-out (cavity) from the one slit of
the oven cavity top plate.
8. Disconnect the wire leads from the thermal cut-out
(cavity).
9. Now, the thermal cut-out (cavity) is free.
TEMPERATURE FUSE (MAGNETRON) REMOVAL
1. Disconnect the power supply cord and remove the oven
from wall and remove outer case. (Refer to procedure of
Removal of Oven from Wall and Outer case Removal)
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Remove the hood fan motor and the hood duct from the
oven cavity, referring to the procedure of  HOOD FANMOTOR, HOOD DUCT AND OVEN LAMP SOCKET
REMOVAL.
5. Disconnect the wire leads from the temperature fuse
(Magnetron).
6. Remove the one (1) screw holding the temperature fuse
(Magnetron) to the oven cavity.
7. Now, the temperature fuse (Magnetron) is free.
COOLING FAN MOTOR REMOVAL
Gap
Rotor Bracket StatorGroove joint pliers
Coil
Shaft
Axis
Stator
Rotor
These are the positions 
that should be pinched 
with pliers
Top of Oven Cavity
Waveguide
Thermal 
Cut-Out
(Cavity) Thermal 
Cut-Out
Thermal 
Cut-Out
Tab
Tab
Slit
INSTALLATION
1. Install the fan blade to the fan motor shaft according to
the following procedure.
2. Hold the center of the bracket which supports the shaft
of the fan motor on the flat table.
3. Apply the screw lock tight into the hole (for shaft) of the
fan blade.
4. Install the fan blade to the shaft of fan motor by pushing
the fan blade with a small, light weight, ball peen hammer
or rubber mallet.
5. Install the fan motor to the hood duct with the two (2) screws.
CAUTION:
* Do not hit the fan blade strongly when installing
because the bracket may be disfigured.
* Make sure that the fan blade rotates smooth after
installation.
* Make sure that the axis of the shaft is not slanted. NOTE: When the tab is broken or turned off, use the another
tab which is fixed near the slit when the new thermal
cut-out is replaced. 
						

							30
R-1480
R-1481
R-1482
1. Disconnect the power supply cord.
2. Open the door and block it open.
3. Remove the three (3) screws holding the base cover to
the oven cavity
4. Remove the base cover from the oven cavity by pulling
REMOVAL)
4. Lift the oven lamp cover up.
5. Now, the oven lamp and the socket are found.
6. Screw the oven lamp off from the lamp socket.
7. Now, the oven lamp is  free.
TURNTABLE MOTOR REMOVAL
down and moving to the left slightly.
5. Disconnect the wire leads from the  turntable motor.
6. Remove two (2) screws holding turntable motor to the
oven cavity.
7. Now the turntable motor is free.
1. Disconnect the power supply cord and remove the oven
from wall and remove outer case. (Refer to procedure of
Removal of Oven from Wall and Outer case Removal)
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Remove the hood fan motor and the hood duct from the
oven cavity, referring to the procedure of  HOOD FAN
MOTOR, HOOD DUCT AND OVEN LAMP SOCKET
REMOVAL.
STIRRER MOTOR REMOVAL
5. Disconnect the wire leads from the stirrer motor.
6. Remove the two (2) screws holding the stirrer motor to
the waveguide of the oven cavity.
7. Remove the stirrer motor from the waveguide.
8. Now, the stirrer motor is free.
9.  When installing the stirrer motor, the shaft of stirrer
motor must be inserted to the stirrer fan shaft. Refer to
the procedure of  STIRRER COVER AND STIRRER
FAN INSTALLATION.
1. Put the stirrer fan on the stirrer cover to match the stirrer
fan shaft to the center of the stirrer support.
2. Insert the shaft of stirrer fan to the shaft of stirrer motor.
3. Insert the cutout of stirrer cover to the tabs on the ceiling.
4. Install the stirrer cover to the oven cavity, and secure it
by one canoe clip.
STIRRER COVER AND STIRRER FAN INSTALLATION
1. Disconnect the power supply cord.
2. Remove one (1) screw holding the hood exhaust louver
to oven cavity front flange.
3. Remove the hood exhaust louver from the oven by
pushing the right and left tabs of the hood exhaust louver.
(Refer to procedure of HOOD EXHAUST LOUVER
OVEN LAMP REMOVAL
1. Disconnect the power supply cord.
2. Open the door and block it open.
3. Remove one (1) screw holding the hood exhaust louver
to oven cavity front flange.
4. Remove the hood exhaust louver from the oven by
pushing the right and left tabs of the hood exhaust louver.
(Refer to procedure of HOOD EXHAUST LOUVER
REMOVAL)
5. Remove one (1) screw holding the control panel to the
oven cavity front  face plate.
6. Release the control panel from the oven cavity front face
plate by lifting it up.
7. Disconnect the wire leads from the relays RY1 and RY2.
CONTROL PANEL ASSEMBLY, CONTROL UNIT  AND KEY UNIT REMOVAL
8. Disconnect the connectors CN-A, CN-B, CN-E and CN-
F from the control unit.
9.  Remove the control panel assembly from the oven.
10.Now, the control panel assembly is free.
11.Disconnect the connector CN-G from the control unit.
12.Remove four (4) screws holding the control unit to the
key fixing plate.
13.Release the two (2) tabs holding the control unit to the
key fixing plate.
14.Now, the control unit is free.
15.Remove the one (1) screw holding the key fixing plate to
the control panel.
16.Release the four (4) tabs holding the key fixing plate to
Shaft
Stirrer Fan
Stirrer 
Cover
Canoe Clip
Stirrer Support
Shaft
Table
Center of
bracket6. Install the hood duct to the oven cavity with the one (1)
screw.
7. Re-install the wire leads to the hole of the hood duct.
8. Connect the wire leads to the fan motor and chassis
support, referring to the pictorial diagram.
9. Refer to procedure of OUTER CASE REMOVAL.  And
reverse their procedure. And re-install the outer case. 
						

							31
R-1480
R-1481
R-1482
the control panel.
17.Remove the key fixing plate from the control panel.
18.Tear the key unit from the key fixing plate.
19.Now, the key unit is free
NOTES FOR KEY UNIT REPLACEMENT
1. Do not reuse the torn key unit because the performance
of the adhesive becomes weak.
2. Before attaching a new key unit, wipe off remaining
adhesive on the key fixing plate surfaces completely with
a soft cloth soaked in alcohol.
3. When attaching the key unit to the key fixing plate, adjust
the upper edge and right edge of the key unit to the
correct position of  key fixing plate.
4. Stick the key unit firmly to the key fixing plate by rubbing
with soft cloth not to scratch.
NOTES FOR NEW CONTROL UNIT REPLACEMENT
1. Before installation of the new CPU into the control panel,
grasp the middle section between thumb and finger,
bend the display board forward a until b breaks as
shown in step 1.
2. To remove the middle section push both sides of the
middle section towards d until c breaks as shown in
step 2.
NOTE: Discard the middle section.
3. After removing the middle section, bend the display
board 90û, positioning the jumper wires into the notches
CN-G
LSI
Control Unit
Middle
sectionBreak
point Display
Boardb
c
Top edge of the display board
Middle
SectionJumper
wires
ba
c
d
Jumper
wires
NotchesControl 
panel
Locator pinClip (F)
Clip (E)
POSITIVE LOCK¨  CONNECTOR (NO-CASE TYPE) REMOVAL
1. Disconnect the power supply cord and remove the oven
from wall and remove outer case. (Refer to procedure of
Removal of Oven from Wall and Outer case Removal)
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Push the lever of positive lock
¨ connector.
5. Pull down on the positive lock¨ connector.
CAUTION: WHEN CONNECTING THE POSITIVE LOCK
¨
CONNECTORS TO THE TERMINALS, IN-
STALL THE POSITIVE LOCK¨ SO THAT THE
LEVER FACES YOU
Terminal
Push
Pull down4
5
Lever Positive lock®
connector
of the display board as shown in step 3.
4. Insert the bottom edge of the display board under the tab
of control panel as shown in step 4.
5. Place the top edge of the display board on the clip (F).
And press the  display board downward as shown in step
4. (Holes in middle of display board should be positioned
into locator pins.)
6. After installing display board, press the CPU downward
90û until CPU is locked into place by the clips.
7. Hold the CPU with the four (4) screws.
8. After installing CPU, make sure jumper wires are not
bent, touching or broken.
Positive lock
¨ connector STEP 1 STEP 2 STEP 3 STEP 4
DOOR SENSING SWITCH, SECONDARY INTERLOCK SWITCH AND MONITOR SWITCH REMOVAL
1. Disconnect the power supply cord and remove the oven
from wall and remove outer case. (Refer to procedure of
Removal of Oven from Wall and Outer case Removal)2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Remove the control panel assembly, referring to the 
						

							32
R-1480
R-1481
R-1482
1. Disconnect the power supply cord and remove the oven
from wall and remove outer case. (Refer to procedure of
Removal of Oven from Wall and Outer case Removal)
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Remove the control panel assembly, referring to the
procedure of CONTROL PANEL ASSEMBLY ,
CONTROL UNIT AND KEY UNIT REMOVAL.
If the door sensing switch, secondary interlock switch and
monitor switch do not operate properly due to a
misadjustment, the following adjustment should be made.
5. Loosen the two (2) screws holding latch hook to the oven
cavity front flange.
6. With door closed, adjust latch hook by moving it back and
forth, and up and down. In and out play of the door
allowed by the upper and lower position of the latch hook
should be less than 0.5mm. The vertical position of the
latch hook should be adjusted so that the door sensing
switch and secondary interlock switch are activated with
the door closed. The horizontal position of the latch hook
should be adjusted so that the monitor switch is activated
with the door closed.
7. Secure the screws with washers firmly.
8. Check all of the switches operation. If any switch has not
activated with the door closed, loosen screw and adjust
the latch hook position.
After adjustment, check the following.
1. In and out play of door remains less than 0.5mm when in
DOOR SENSING SWITCH, SECONDARY INTERLOCK SWITCH AND MONITOR SWITCH ADJUSTMENT
DOOR REPLACEMENT
DOOR ASSEMBLY REMOVAL
1. Disconnect the power supply cord and remove the oven
from wall and remove outer case. (Refer to procedure of
Removal of Oven from Wall and Outer case Removal)
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Remove the hood exhaust louver from the oven cavity by
pushing the right and left tabs of the hood exhaust louver.
(Refer to the procedure of HOOD EXHAUST LOUVER
REMOVAL.)
5. Insert a putty knife (thickness of about 0.5mm) into the
gap  A  between the door stopper and the choke cover
as shown in Figure C-3 to free engaging parts.
6. Lift up the door stopper.
7. Now, the door stopper is free from the door assembly.8. Lift up the door assembly to release the upper and lower
door hinge pins from the upper and lower oven hinges.
9. Now, the door assembly is free.
Note: When the individual parts are replaced, refer to
Door Disassembly.
DOOR ASSEMBLY RE-INSTALL
1. On re-installing door, insert the lower oven hinge to lower
door hinge pin.
2. Insert the upper oven hinge to the upper door hinge pin.
3. Shut the door (close the contacts of interlock switches).
4. Make sure upper and lower oven hinges are inserted into
the upper an lower door hinge pins.
5. Make sure the door is parallel with oven face lines (left
and upper side lines) and door latch heads pass through the latched position. First check upper position of latch
hook, pushing and pulling upper portion of door toward
the oven face. Then check lower portion of the latch
hook, pushing and pulling lower portion of the door
toward the oven face. Both results (play in the door)
should be less than 0.5mm.
2. The door sensing switch and secondary interlock switch
interrupt the circuit before the door can be opened.
3. Monitor switch contacts close when door is opened.
4. The contact of door sensing switch and secondary
interlock switch open within 1.2mm gap between right
side of cavity face plate and door when door is open.
5. Re-install outer case and check for microwave leakage
around door with an approved microwave survey meter.
(Refer to Microwave Measurement Procedure.)
Figure C-1. Latch Switch Adjustments procedure of CONTROL PANEL ASSEMBLY ,
CONTROL UNIT AND KEY UNIT REMOVAL.
5. Remove the two (2) screws holding the latch hook to the
oven cavity front flange.
6. Remove the latch hook from the oven cavity front flange.
7. Disconnect the wire leads of each switch.
8. Remove each switch from the latch hook by pushing the
one (1) stopper tub holding each switch.
9. Now, each switch is  free.
Re-install
1. Re-install each switch in its place. The secondary interlockswitch is in the lower position, door sensing switch is in
the upper position and the monitor switch is in the middle
position.
2. Re-connect wire leads to each switch. Refer to pictorial
diagram.
3. Secure the latch hook (with two (2) mounting screws) to
oven cavity front flange.
4. Make sure that the monitor switch is operating properly
and check continuity of the monitor circuit.    Refer to
chapter Test Procedure and Adjustment procedure.
Secondary
Interlock
Switch
Monitor
Switch
Monitor
Fuse
Door
Sensing
Switch
Latch
Hook
DoorLatch
Heads 
						

							33
R-1480
R-1481
R-1482
latch holes correctly.
6. Re-install the door stopper to the door assembly.
7. Re-install the hood exhaust louver to the oven cavity
front face plate.
Note: After any service to the door;
(A) Make sure that door sensing switch and secondary
interlock switch are operating properly. (Refer to
chapter Test Procedures.)
(B) An approved microwave survey meter should be
used to assure compliance with proper microwave
radiation emission limitation standards.
After any servicing, make sure of the following :
1. Door latch heads smoothly catch latch hook through
latch holes and that latch head goes through center of
latch hole.
2. Deviation of door alignment from horizontal line of cavity
face plate is to be less than 1.0mm.
3. Door is positioned with its face pressed toward cavity
face plate.
4. Re-install outer case and check for microwave leakage
around door with an approved microwave survey meter.
(Refer to Microwave Measurement Procedure.)
Note: The door on a microwave oven is designed to
act as an electronic seal preventing the leakage
LATCH SPRING, LATCH HEAD AND DOOR PANEL
13.Release the latch spring from the tab of the latch head
and tab of the door frame.
14.Release the latch head from the door frame.
15.Now, the latch spring, latch head and door frame are
free. 1. Disconnect the power supply cord and remove the oven
from wall and remove outer case. (Refer to procedure of
Removal of Oven from Wall and Outer case Removal)
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Remove the hood exhaust louver from the oven cavity by
pushing the right and left tabs of the hood exhaust louver.
(Refer to the procedure of HOOD EXHAUST LOUVER
REMOVAL.)
5. Remove door assembly, refer to Door Replacement.
Replacement of door components are as follows:
6. Place door assembly on a soft cloth with latches facing
up.
Note: As the engaging part of choke cover and door frame
are provided at 15 places, do not force any particular
part.
CHOKE COVER
7. Insert a putty knife (thickness of about 0.5mm) into the
gap A between the choke cover and door stopper and
between the choke cover and the door frame as shown
Figure C-3 to free engaging parts.
8. Pry the principles of the lever and  lift up the choke cover
by inserting a putty knife in order shown in Figure C-3.
9. Now choke cover is free from door panel and door frame.
DOOR FRAME
10.Remove six (6) screws holding the door panel and the
door handle to the door frame assembly.
11.Release the door frame assembly from the door panel.
NOTE: It is easier to release the engaging parts of the upper
or lower door hinge pin side at first.
12.Now, door frame assembly is free.of microwave energy from oven cavity during
cook cycle. This function does not require that
door be air-tight, moisture (condensation)-tight
or light-tight. Therefore, occasional appearance
of moisture, light or sensing of gentle warm air
movement around oven door is not abnormal
and do not of themselves indicate a leakage of
microwave energy from oven cavity.
Figure C-2. Door Replacement and adjustment
DOOR DISASSEMBLY
Figure C-3. Door Disassembly
DOOR GLASS
16.Remove the glass stopper from the door frame by
releasing the tab of door frame.
17.At first, slide the door glass toward the glass stopper
side, and then slide it up. And release it from the right and
lower long tabs of the door frame.
18.Release the door glass from the upper long tab of the
door frame.
19.Release the door glass from the long tabs of  the door
frame.
20.Now, the door glass is free.
Upper Door
Hige Pin
Upper 
Oven
Hige
Lower 
Oven Hige
Lower Door
Hige Pin RE-INSTALL
RE-INSTALL
Door Stopper Door assembly
Latch
Heads
Hood Exhaust Louver Tab
Tab
A
Choke Cover
Door FrameDoor Stopper
Putty Knife 
						

							34
R-1480
R-1481
R-1482
6
45
12
3
6
45
12
3 A
B
C
D
E
F
G
HA
B
C
D
E
F
G
H
Figure S-1. Pictorial Diagram
HIGH
VOLTAGE
RECTIFIER HIGH VOLTAGE
CAPACITOR
HIGH VOLTAGE
WIRE A
HIGH VOLTAGE COMPONENTS
POWER 
TRANSFORMERPower Supply
cord 120V 60Hz
1 2 3
WHT
GRNBLK
WHT
GRNBLK
CAVITY
THERMAL
CUT-OUT
MAGNETRON
TEMPERATURE 
FUSE
WHTRED
BLKREDBLK
FAN
MOTOR
TURNTABLE
MOTOR
GRYORGWHTORG
ORG
RED
WHT
ORG
BLK WHTHOOD LAMPS
& SOCKETS
Blue 
Marking 
Blue Marking OVEN LAMP & SOCKET
to Chassis Support
CN-E
GRYWHTWHT
WHTBLU
WHT
WHTWHT
BLK
SECONDARY
INTERLOCK
SWITCHN.O. N.C.
COM.COM.
MONITOR
SWITCHFUSE & HOLDER
N.O. N.O.
GRNRED
N.O.
COM.
DOOR SENSING SWITCH
CN-BCN-E
CN-F
CN-E
CN-A
1 1
9
11
132
12
3 5 7 PRIMARY
INTERLOCK
RELAY 
RY1 RY2
RY4
RY1
N.O.
RY1
COM.
RY2
N.O.
RY2
COM.
GRY
C100 T1HOOD FAN MOTOR
STIRRER MOTOR
12 3 4 5 6
WHTRED
YLW
BLUBLK WHTRED
YLW
BLUBLK
12
RED GRN
12 3 4 5 6 7
YLW WHT
BLK
REDCN-A
W
H
T
G
R
Y
HOOD FAN
THERMAL
CUT-OUT
RED
WHTREDRED
RED
ORG
REDORG
GRN
to Right Base Plate
GRN
12 3 4 5 6 7
BLK RED
ORG
WHT8 9
ORGCN-B
IC1
IC2
COM. COM.RY2:
CN-G
RY5
REDBLKREDORGORG
BLK
RED
WHTWHT
RED
MAGNETRON
W
H
T
R
E
D
WHT 
						

							35
R-1480
R-1481
R-1482
6
45
12
3
6
45
12
3 A
B
C
D
E
F
G
HA
B
C
D
E
F
G
H
Figure S-2. Control Panel Circuit
+
–
+ –
+–
+
–
A 7
VRS1 (J1)
D20 R110
R110 47 1/2w
C110 0.033µ/250v C110
D25 D26 D27 D28
T1
D1
D1-D4
11ES1
Q20
KRA101M
Q24
KRA101M
R20
1k 1/2w
RY4
RY5
RY1
RY2 NO NCRY3
Q25
KRA101M
Q26
KRA101M
Q28
KRA101MQ30
KRA101M
Q27
KRC243MQ40
KRA101M MOTOR RUN
CAPACITOR
TURNTABLE
MOTOR
HOOD LAMP
HOOD THERMO
HOOD MOTOR

COM(H)
FAN MOTOR
OVEN LAMP
STIRRER MOTOR
MICROHIGH

LOW

 COMQ4
DTA123ES
C10 0.1µ/50v
VC
C73 330pF
C72 330pF
C71 330pF
C70 330pFR10 3.3 1/2w
Note
Fluorescent display tube
VF1
MIX CONV COOK LBS KG
TURNTABLE
OFF HELP
1. 2 F
33. 32 F
VF2
VP VP
Q3
KRA101M R4 510 1/2w R3 750 1w
VCC
1 
10 
20 
30 
32 3340 50
60 64
P30
P31
P32
P33
P34
P35
P36
P37
P00
P01
P02
P03
P04
P05
P06
P07
P10
P11
P12
P13
P14
P15
P16
P17
P20
P21
P22
P23
P24
P25
P26
P27 VEE
AVSS
VREF
AN7
AN6
AN5
AN4
AN3
AN2
AN1
AN0
P55
P54
P53
P52
P51
P50
P47
P46
P45
P44
P43
P42
INT1
P40
RESET
P71
P70
XIN
XOUT
VSS
C100
7µ/230vD2
D3 D4
a b
cd5
6
11
SSR1
C30
R31 4.7k
DOOR
SWITCHCF1
CST4.00MGW
CLOCK KITCHEN
TIMERSTOP
CLEAR POWER
LEVEL
MINUTE
PLUSNIGHT
LIGHT
FAN
HI / LO  TURN
TABLE
ON / OFF

 CUSTOM
HELP
POPCORN
BREAK
FAST
COMPU
COOK
COMPU
DEFROST
SNACKS
&
REHEATWORK
LIGHT
172
83
94
056
D30 S101D01 
133 2
3 2
1
4
10G471K
C1 0.1µ/50v
C20 10µ/35v
C21 0.1µ/50v R30 15k
D31
(J2)
(J4)
(J6)
(J3)
(J5)
(J7)
IC1
IZA876DR
(J15)C9
0.1µ
/50vSP40C2 1000µ/35v
C6 10µ/35v C5
C7 C8ZD1 HZ6A3
ZD3 HZ5C2
ZD4
HZ4A2
R7
4.7k R8
4.7kR1 4.3k 1/2w
R70 3.3k
R71 3.3k
R72 3.3k
R73 3.3k
D71
R77 3.3k
D72
R78 3.3k
D73
R79 3.3k
D74
R80 3.3k
D752
R81 3.3k
D76
R82 3.3k
D77
R83 3.3kR40 3.3k
R91 100k
R92 100k
R93 100k
4 P1
5 P2
6 P3
7 P4
8 P5
9 P6
10 P7
11 P8
12 P9
13 P10
15 P11
16 P12
17 P13
19 P14
20 P15
22 1G
23 2G
24 3G
25 4G
26 5G
27 6G
28 7G
29 8G
A 1
A 3
A 5
E 1 E 2G 1 G 2 G 3 G 4 G 5 G 6 G 7 G 8
G12 G11 G10 G 9
B 9
B 7
B 5
B 3
B 1COM
COMN.O.
N.O.



START
TOUCH ON
: IF NOT SPECIFIED  1/8w ± 5%: IF NOT SPECIFIED  1SS270A: IF NOT SPECIFIED  0.01µF/16v  
						

							36
R-1480
R-1481
R-1482
6
45
12
3
6
45
12
3 A
B
C
D
E
F
G
HA
B
C
D
E
F
G
H
Figure S-3. Printed Wiring Board
DIP
,BFB
1
R10
C6C10
R4
R1
D4
(ZD2)
S1 S2
P (R2)D1 SP40C5
C7
D25
D20 46
4847 RY4
RY5
T1
(470V)
VRS1
(CN - A)
CN - A
AC(N) TTM RY3
AC(H)OL MICRO
FM ZD3
ZD1 ZD4 CF1 (J15)
R7
R40 27
28
29
30
31
32 (J11) (J10)
(R76)
(R100)
(D70)
D71
D72
D73
D74
D75
D76R77
R79
R80
R81
R82
R70
R71
R72
R73 
35 
3 1 B B  B 
B 
B  E  E E 
E B 
E 
E E E 
E 
E  B  B B 
B 
B  Q30  Q20 Q40 
Q3 
R83 R78
D77
(IC2)
34
42
C3
4356
1
3 5 7
11 7
2
9
1
75 3 1 9
R30
C110
R110R3 Q26
SSR1Q25Q24
Q4
D30
Q28
(Q1) IC1(J12)
(J13)
(J14)
C72C30 C8
C70
C71 C73
QKITPB027MRE0
R91
R92
R93 (J6)  (J4)  (J2) (J5)  (J7)  (J3)  33
CN - G
CN - E
R20  D31  R8 
C21 
R31 40 43C2
C9
C4 44
45C1C100 D2 D3
41
39 38 
C20 
RY2 (J1) 
RY1  Q27 
D26 
D28 
D27 
(CN - B)
CN - B
HOOD
LAMPHOOD
THERMHOOD
MHIGHHOOD
MLOW COM
37  36 
(CN - G)
112
12
1
133
33 112
32 64
2
3
4
5
6
7
8
9
10
11
12
13
19 14
15
16
17
18
20
21
22
23
24
25
26
  
						

							37
R-1480
R-1481
R-1482
PARTS LIST
Note: The parts marked ÒDÓ may cause undue microwave exposure.
The parts marked Ò*Ó are used in voltage more than 250V.
¤ MARK: PARTS DELIVERY SECTION
ELECTRIC PARTS
1- 1 FH-DZB012MRY0 M High voltage rectifier assembly  1 AK
1- 2 RC-QZA173WRE0 M High voltage capacitor  1 AR
1- 3 QFS-TA013WRE0 M Temperature fuse 150ûC (Magnetron)  1 AG
1- 4 RMOTDA182WRE0 M Turntable motor  1 AQ
1- 5 RMOTDA214WRE0 M Stirrer motor  1 AQ
1- 6 RTHM-B005MRE0 M Thermal cut-out N.O. 60ûC (Hood Fan)  1 AG
1- 7 RTRN-B055MRE0 M Power transformer  1 BE
1- 8 RV-MZA280WRE0 M Magnetron 1 BD
1- 9 QFSHDB003MRE0 M Fuse holder  1 AD
1-10 QSW-MA110WRE0 M Secondary interlock and door sensing switches  2 AE
1-11 FFS-BA016/KIT M Monitor switch  with fuse assembly  1 AF
1-12 FACCDB011MRE0 M Power supply cord  1 AP
1-13 QSOCLB006MRE0 M Oven lamp socket  3 AE
1-14 FMOTEA366WRK0 M Hood fan motor  1 BE
1-15 RMOTEA346WRE0 M Fan motor  1 AR
1-16 RLMPTA071WRE0 M Oven lamp  3 AG
1-17 RTHM-A080WRE0 M Thermal cut-out 145ûC (Cavity)  1 AG
CABINET PARTS
2- 1 LSTY-B021MRP0 M Rear stay  1 AF
2- 2 PDIF-B018MRF0 M Hood exhaust louver  [R-1480]  1 AT
2- 2 PDIF-B019MRF0 M Hood exhaust louver  [R-1481]  1 AT
2- 2 PDIF-B020MRF0 M Hood exhaust louver  [R-1482]  1 AT
2- 3 GDAI-B045MRP0 M Right base plate  1 AM
2- 4 PCUSUB040MRP0 M Base cover cushion  1 AA
2- 5 GCABUB084MRP0 M Outer case cabinet [R-1480]  1 BA
2- 5 GCABUB085MRP0 M Outer case cabinet [R-1481]  1 BB
2- 5 GCABUB086MRP0 M Outer case cabinet [R-1482]  1 BC
2- 6 TMAPCB052MRR0 M Schematic diagram  1 AB
2- 7 FANGKB009MRY0 M Hood lamp glass assembly [R-1480]  1 AN
2- 7 FANGKB010MRY0 M Hood lamp glass assembly [R-1481]  1 AM
2- 7 FANGKB011MRY0 M Hood lamp glass assembly [R-1482]  1 AM
2-7-1 LANGQB016MRP0 M Hood lamp glass angle [R-1480]  1 AG
2-7-1 LANGQB020MRP0 M Hood lamp glass angle [R-1481]  1 AG
2-7-1 LANGQB027MRP0 M Hood lamp glass angle [R-1482]  1 AG
2-7-2 PGLSPB004MRE0 M Hood lamp glass  1 AH
2- 8 PCOVPB064MRt0 M Base cover [R-1480]  1 AY
2- 8 PCOVPB066MRt0 M Base cover [R-1481]  1 AY
2- 8 PCOVPB067MRt0 M Base cover [R-1482]  1 AY
CONTROL PANEL PARTS
3- 1 DPWBFB081MRU0 M Control unit 1 BL
3- 1A QCNCMA447DRE0 M 4-pin connector CN-A 1 AA
3- 1B QCNCMA448DRE0 M 5-pin connector CN-B 1 AA
3- 1C QCNCMA275DRE0 J 2-pin connector CN-E 1 AB
3- 1D QCNCWA030DRE0 J 12-pin connector CN-G 1 AE
3- 1E RV-KXB004MRE0 M Fluorescent display tube 1 AS
3- 1F PTPEHB010MRE0 M Tape 2mm 1 AB
C1 RC-KZA087DRE0 J Capacitor     0.1 uF    50V 1 AB
C2 VCEAB31VW108M J Capacitor    1000 uF    35V 1 AF
C5 VCKYD11CY103N J Capacitor    0.01 uF    16V 1 AH
C6 VCEAB31VW106M J Capacitor      10 uF    35V 1 AB
C7-8 VCKYD11CY103N J Capacitor    0.01 uF    16V 2 AH
C9-10 RC-KZA087DRE0 J Capacitor     0.1 uF    50V 2 AB
C20 VCEAB31VW106M J Capacitor      10 uF    35V 1 AB
C21 VCEAB31HW104M J Capacitor     0.1 uF    50V 1 AM
C30 VCKYD11CY103N J Capacitor    0.01 uF    16V 1 AH
C70-73 VCKYD11HB331K J Capacitor     330 pF    50V 4 AA
C100 RC-QZB014MRE0 M Capacitor       7 uF   230V 1 AK
C110 RC-QZB019MRE0 M Capacitor   0.033 uF   250V 1 AC
CF1 RCRS-A010DRE0 J Ceramic resonator (CST4.00MGW) 1 AD
D1-4 VHD11ES1///-1 J Diode (11ES1) 4 AB
D20 VHD1SS270A/-1 J Diode (1SS270A) 1 AA
D25-28 VHD1SS270A/-1 J Diode (1SS270A) 4 AA
D30-31 VHD1SS270A/-1 J Diode (1SS270A) 2 AA
D71-77 VHD1SS270A/-1 J Diode (1SS270A) 7 AA
REF. NO. PART NO. ¤ DESCRIPTION QTY CODE
*
*
*
D* 
						

							38
R-1480
R-1481
R-1482
REF. NO. PART NO. ¤ DESCRIPTION QTY CODE
IC1 RH-IZA876DRE0 J LSI 1 AW
Q3 VSKRA101M//-3 J Transistor (KRA101M) 1 AB
Q4 VSDTA123ES/-3 J Transistor (DTA123ES) 1 AA
Q20 VSKRA101M//-3 J Transistor (KRA101M) 1 AB
Q24-26 VSKRA101M//-3 J Transistor (KRA101M) 3 AB
Q27 VSKRC243M//-3 J Transistor (KRC243M) 1 AB
Q28 VSKRA101M//-3 J Transistor (KRA101M) 1 AB
Q30 VSKRA101M//-3 J Transistor (KRA101M) 1 AB
R1 VRD-B12HF432J J Resistor      4.3k ohm   1/2W 1 AH
R2 VRD-B12EF152J J Resistor      1.5k ohm   1/4W 1 AA
R3 VRS-B13AA751J J Resistor       750 ohm   1W 1 AH
R4 VRD-B12HF511J J Resistor       510 ohm   1/2W 1 AB
R7-8 VRD-B12EF472J J Resistor      4.7k ohm   1/4W 2 AA
R10 VRD-B12HF3R3J J Resistor       3.3 ohm   1/2W 1 AH
R20 VRD-B12HF102J J Resistor        1k ohm   1/2W 1 AA
R30 VRD-B12EF153J J Resistor       15k ohm   1/4W 1 AA
R31 VRD-B12EF472J J Resistor      4.7k ohm   1/4W 1 AA
R40 VRD-B12EF332J J Resistor      3.3k ohm   1/4W 1 AA
R70-73 VRD-B12EF332J J Resistor      3.3k ohm   1/4W 4 AA
R77-83 VRD-B12EF332J J Resistor      3.3k ohm   1/4W 7 AA
R91-93 VRD-B12EF104J J Resistor      100k ohm   1/4W 3 AA
R110 VRS-A12HA470J J Resistor        47 ohm   1/2W 1 AH
RY1-2 RRLY-A113DRE0 M Relay (DU24D1-1PR(M)) 2 AG
RY3-4 RRLY-A080DRE0 J Relay (OJ-SH-124LM) 2 AG
RY5 RRLY-A112DRE0 M Relay (VE24HSE-K) 1 AH
SSR1 RH-SZA009DRE0 M Solid state relay 1 AG
SP40 RALM-A014DRE0 J Buzzer (PKM22EPT) 1 AG
T1 RTRNPB014MRE0 M Transformer 1 AM
VRS1 RH-VZA032DRE0 J Varistor (10G471K) 1 AE
ZD1 VHEHZ6A3///-1 J Zener diode (HZ6A-3) 1 AC
ZD3 VHEHZ5C2///-1 J Zener diode (HZ5C-2) 1 AA
ZD4 VHEHZ4A2///-1 J Zener diode (HZ4A-2) 1 AA
3- 2 FPNLCB205MRK0 M Control panel sub. assembly [R-1480] 1 AZ
3- 2 FPNLCB211MRK0 M Control panel sub, assembly [R-1481] 1 AZ
3- 2 FPNLCB212MRK0 M Control panel sub, assembly [R-1482] 1 AZ
3- 2-1 FUNTKB153MRE0 M Key unit [R-1480] 1 AU
3- 2-1 FUNTKB159MRE0 M Key unit [R-1481] 1 AU
3- 2-1 FUNTKB160MRE0 M Key unit [R-1482] 1 AU
3- 2-2 GMADIB030MRF0 M Display window 1 AF
3- 3 XEPSD30P10XS0 M Screw; 3mm x 10mm 5 AB
OVEN PARTS
4- 1 FFTA-B003MRK0 M Exhaust damper assembly  1 AH
4- 2 FROLPB024MRK0 M Turntable support  assembly  1 AK
4- 3 NTNT-A090WRE0 M Turntable tray  1 AN
4- 4 LANGKB010MRP0 M Capacitor holder  1 BB
4- 5 FCOVPB012MRY0 M Stirrer cover assembly  1 AK
4- 6 FFAN-B006MRK0 M Stirrer fan assembly  1 AL
4- 7 ************* M Oven cavity (Not replaceable part)  1 --
4- 8 PPACGB014MRF0 M Turntable motor packing  1 AA
4- 9 PHOK-B017MRF0 M Latch hook  1 AG
4-10 LANGTB036MRP0 M Unit mounting plate  1 AP
4-11 NFANPB001MRE0 M Fan blade  1 AC
4-12 LBSHC0037WRE0 M Cord bushing  1 AB
4-13 PCOVPB065MRP0 M Oven lamp cover  1 AD
4-14 PDUC-B077MRP0 M Hood intake duct  1 AG
4-15 PCUSUB039MRP0 M Hood intake duct cushion  2 AA
4-16 PFILWB005MRP0 M Lamp filter  1 AB
4-17 PSKR-B012MRP0 M Magnetron air guide 1 AB
4-18 LANGTB040MRP0 M Chassis support  2 AE
4-19 PDUC-B078MRF0 M Hood duct  1 AX
4-20 PCUSUB043MRP0 M Hood duct cushion  1 AB
4-21 LSTPPB031MRF0 M Door stopper  1 AC
4-22 PCUSUB045MRP0 M Cushion  1 AE
DOOR PARTS
5 CDORFB203MRK0 M Door assembly [R-1480]  1 BD
5 CDORFB205MRK0 M Door assembly [R-1481]  1 BE
5 CDORFB206MRK0 M Door assembly [R-1482]  1 BE
5- 1 FDORFB060MRT0 M Door panel assembly  1 AX
5- 2 FCOV-B125MRK0 M Door frame assembly [R-1480] 1 AS
5- 2 FCOV-B127MRK0 M Door frame assembly [R-1481] 1 AS
5- 2 FCOV-B128MRK0 M Door frame assembly [R-1482] 1 AS
D
D
DD
D
D
D
D
D