Sharp Xg V10xu Projector User Manual

							E-40
Basic Operation
Basic Operations
Projector
Using the GUI (Graphical User Interface) Menu Screen
(GUI) On-screen Display
1
INPUT 1, 2 (RGB) or 3 (DIGITAL) mode
1
INPUT 4, 5 (VIDEO) mode
4(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1Press MENU to display the INPUT 1, 2, 3, 4 or 5
mode menu bar.
2Press ß/© to select an adjustment menu on the
menu bar.
3Press ∂/ƒ to select a specific adjustment item.
4To display a single adjustment item, press ENTER
after selecting the item. Only the menu bar and
the selected adjustment item will appear.
5Press ß/© to adjust the item.
6Press UNDO to return to the previous screen.
7To exit from the GUI, press MENU.
•For details on items on the menu screen, see the tree charts
on pages 41 and 42.
ß 2 © ß 2 ©
ß 
2 ©MOUSEADJ.
1.2.3 4.5.6
1, 7
6 2, 3, 54
6
This projector has two sets of menu screens that allow you to adjust the image and various projector settings.
These menu screens can be operated from the projector or the remote control with the following procedure.
∂
3ƒ
ß 
5 ©
∂
3ƒ
ß 
5 ©
Remote Control
ß 5 ©       
						

							E-41
Basic Operation
Menu Bars
Items on the INPUT 1, 2 or 3 Mode Menu Bar
Main menuSub menuMain menuSub menu
PictureOptions
Options Fine Sync
AudioTint
30 30
Color
30 30
Sharp
30 30
ContrastLamp 1
Lamp 2 
30 30
Bright
30 30
Red
30 30
Blue
Reset
30 30
CLR Temp
Progressive Mode Signal Type
3 3
Component RGB
2D Progressive
3D Progressive
Film Mode
Auto Sync Clock
150 150

150 150
[ON/OFF]
Auto Sync Disp[ON/OFF]
Phase
60 60
H-Pos
V-Pos
Reset
Save Setting
Select Setting
Special Modes
60 60
Signal Info1
2
•
•
7
Resolution800600
640480
1
2
•
•
7
Resolution
Vert Freq
75 Hz
72 Hz 1
2
•
•
7
Resolution800600
640480Vert Freq
75 Hz
72 Hz
Resolution
Hor Freq
Vert Freq640480
37.5 kHz
72 Hz
Economy Mode OSD Display
Background
[ON/OFF]
[ON/OFF]
Auto Power Off
ID No. DisplayMNTR Out/RS232C
[ON/OFF]
Startup ImageTreble
30 30
Balance
30 30
Bass
30 30
Reset
Pict in Pict
Sharp
Sharp Custom
Custom Blue
None
None
Display Off
Standby Off
Display On Normal
Level A
Level BLamp Timer
Lamp ModeBoth Lamps
Lamp 1 Only
Lamp 2 Only
Equal Use
PRJ Mode
Stack Setting
Keylock Level
Set Inputs
RS-232C
Set ID No.
Password
Optional BoardCeiling
Front
Ceiling
Rear Front
Rear
Level B
Input 1
Input 2
Input 3
Input 4
Input 5
9600bps
115200bps
ID No. Input 6
38400bps
Old Password
Reconfirm New Password Slave
Level A Master Normal
NormalLanguage
English
Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português
Status
[ON/OFF]
[ON/OFF]
[ON/OFF]
[ON/OFF]
[ON/OFF]
[ON/OFF]
•The resolution, vertical frequency and horizontal frequency figures displayed above are for example purposes only.
•“Color”, “Tint”, and “Sharp” appear only when Component input is selected in INPUT 1 or 2 mode. For INPUT 3 (DVI), in
“Picture” menu, only “CLR Temp” is active and the other menus are displayed in gray. In “Fine Sync” menu, only “Signal
Info” is active and the other menus are displayed in gray.
•Only the items highlighted in the tree charts above can be adjusted.
•To adjust the items under the sub menu, press © after selecting the sub menu. 
						

							E-42
Basic Operation
Menu Bars
Items on the INPUT 4 or 5 Mode Menu Bar
Main menuSub menuMain menuSub menu
PictureOptions
AudioTint
30 30
Color
30 30
Sharp
30 30
ContrastLamp 1
Lamp 2 
30 30
Bright
30 30
Red
30 30
Blue
Reset
30 30
CLR Temp
Progressive Mode Signal Type
3 3
Video
Component
2D Progressive
3D Progressive
Film Mode
Economy Mode Background
[ON/OFF]Auto Power Off
ID No. DisplayMNTR Out/RS232C
[ON/OFF]
Startup ImageTreble
30 30
Balance
30 30
Bass
30 30
Reset
Sharp
Sharp Custom
Custom Blue
None
None
Display Off
Standby Off
Display On Options3D DNR
OSD Display
[ON/OFF]
Video SystemNormal
PAL (50/60Hz) Level A
SECAM Level B
Auto
NTSC3.58
PAL–M
PAL–N NTSC4.43Lamp Timer
Lamp ModeBoth Lamps
Lamp 1 Only
Lamp 2 Only
Equal Use
PRJ Mode
Stack Setting
Keylock Level
Set Inputs
RS-232C
Set ID No.
Password
Optional BoardCeiling
Front
Ceiling
Rear Front
Rear
Level B
Input 1
Input 2
Input 3
Input 4
Input 5
9600bps
115200bps
ID No. Input 6
38400bps
Old Password
Reconfirm New Password Slave
Level A Master Normal
Normal
Language
English
Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português
Status
[ON/OFF]
[ON/OFF]
[ON/OFF]
[ON/OFF]
[ON/OFF]
[ON/OFF]
•Only the items highlighted in the tree charts above can be adjusted.
•To adjust the items under the sub menu, press © after selecting the sub menu.
•When selecting “Component” on “Signal Type”, the tree chart becomes the same as the one in INPUT 1, 2 or 3 mode. 
						

							E-43
Basic Operation
Adjusting the Picture
You can adjust the projector’s picture to your prefer-
ences with the following picture settings.
Description of Adjustment Items
Projector
For less contrast
For less brightness
For less color intensity
Skin tones become purplish
For less sharpness
For weaker red
For weaker blue Selected itemFor more contrast
For more brightness
For more color intensity
Skin tones become greenish
For more sharpness
For stronger red
For stronger blue
ß button
© button
All image adjustment items are returned to the factory preset
settings. Contrast
Bright
Color
Tint
Sharp
Red
Blue
Reset
•“Color”, “Tint” and “Sharp” do not appear for RGB input in
INPUT 1 or 2 mode.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1Press MENU. Menu bar and “Picture” menu
screen appear. GUI operation guide is also
displayed.
2Press ∂/ƒ  to select a specific adjustment item.
3Press ß/© to move the 
 mark of the selected
adjustment item to the desired setting.
4To exit from the GUI, press MENU.
•To reset all adjustment items, select “Reset” on the “Picture”
menu screen and press ENTER.
•The adjustments can be stored separately in the INPUT 1
to 5 modes.
•Depending on the type of signal received, “Sharp” may not
be adjustable for COMPONENT input in INPUT 1 or 2 mode.
MOUSEADJ.
Remote Control
1.2.3 4.5.6
1, 4
2, 3
(GUI) On-screen Display
e. g. (RGB input in INPUT 1 or 2 mode)
1
2    
						

							E-44
Basic Operation
Adjusting the Picture
Projector Remote ControlAdjusting the Color Temperature
This function can be used to adjust the color
temperature to suit the type of image input to the
projector (video, computer image, TV broadcast, etc.).
Decrease the color temperature to create warmer,
reddish images for natural flesh tones, or increase to
create cooler, bluish images for a brighter picture.
Description of Color Temperature
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1Press MENU. Menu bar and “Picture” menu
screen appear. GUI operation guide is also
displayed.
2Press ∂/ƒ to select “CLR Temp”.
3Press ß/© to move the 
 mark of the selected
adjustment item to the desired setting.
4To exit from the GUI, press MENU.
1.2.3 4.5.6
1, 4
2, 3
(GUI) On-screen Display
Increases color temperature for
cooler, bluish, florescent-like
images.
(High color temperature)Decreases color temperature for
warmer, reddish,
incandescent-like images.
(Low color temperature)
3
3(Red) ß button© button (Blue)
MOUSEADJ.  
						

							E-45
Basic Operation
Projector Remote ControlSelecting the Signal Type
This function allows you to select the input signal type
RGB (VIDEO) or COMPONENT for INPUT 1, 2, 4 or 5
port.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1Press MENU. Menu bar and “Picture” menu
screen appear. GUI operation guide is also
displayed.
2Press ∂/ƒ to select “Signal Type”, and then
press©.
3Press ∂/ƒ to select “RGB (VIDEO)” or
“Component”.
4Press ENTER to save the setting.
5To exit from the GUI, press MENU.
Adjusting the Picture
ProjectorRemote Control
1.2.3 4.5.6
1, 5
2, 3
4
(GUI) On-screen Display
1.2.3 4.5.6
1, 5
2, 3
4
(GUI) On-screen Display
Progressive Mode
This function allows you to select the progressive display
of a video signal. The progressive display projects a
smoother video image.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1Press MENU. Menu bar and “Picture” menu
screen appear. GUI operation guide is also
displayed.
2Press ∂/ƒ to select “Progressive Mode”, and
then press ©.
3Press ∂/ƒ to select “2D Progressive”, “3D
Progressive” or “Film Mode”.
4Press ENTER to save the setting.
5To exit from the GUI, press MENU.
MOUSEADJ.
MOUSEADJ.
Progressive Mode
Selects the progressive conversion mode.
2D Progressive
This function is useful to display fast-moving images such as sports
and action films. Mode that optimizes the image in a displayed frame.
3D ProgressiveThis function is useful to display relatively slow-moving images such
as drama and documentary more clearly.
Mode that optimizes the image by estimating the movement of a
number of preceding and succeeding frames.
Film ModeReproduces the image of film software clearly. Displays the optimized
image of film transformed with three-two pull down enhancement to
progressive mode images.
•Film Mode cannot work with PAL 50 Hz.   
						

							E-46
Basic Operation
When displaying computer patterns which are very
detailed (tiling, vertical stripes, etc.), interference may
occur between the LCD pixels, causing flickering,
vertical stripes, or contrast irregularities in portions of
the screen. Should this occur, adjust “Clock”, “Phase”,
“H-Pos” and “V-Pos” for the optimum computer image.
•Computer image adjustments can be made easily by
pressing AUTO SYNC (). See page 49 for details.
(GUI) On-screen Display
Projector
Adjusts vertical noise.
Adjusts horizontal noise (similar to tracking on your VCR).
Centers the on-screen image by moving it to the left or right.
Centers the on-screen image by moving it up or down.Clock
Phase
H-Pos
V-Pos
Description of Adjustment Items
(Select the desired computer input mode with INPUT 1
or 2.)
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1Press MENU.
2Press ß/©  to select “Fine Sync”.
3Press  ∂/ƒ  to select a specific adjustment item.
4Press ß/© to move the 
 mark of the selected
adjustment item to the desired setting.
5To exit from the GUI, press MENU.
•To reset all adjustment items, select “Reset” on the “Fine
Sync” menu screen and press ENTER.
2
Description Selected item
Remote Control
Adjusting the Computer Images (RGB menu only)
1.2.3 4.5.6
1, 5
2, 3, 4
3
MOUSEADJ.   
						

							E-47
Basic Operation
Adjusting the Computer Images (RGB menu only)
Saving and Selecting Adjustment Settings
This projector allows you to store up to seven adjustment
settings for use with various computers. Once these
settings are stored, they can be easily selected each
time you connect a computer to the projector.
Saving the adjustment setting
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1Press MENU.
2Press ß/© to select “Fine Sync”.
3Press ∂/ƒ to select “Save Setting”, and then
press ©.
4Press ∂/ƒ to select the desired memory location
of the setting.
5Press ENTER to save the setting.
6To exit from the GUI, press MENU.
Selecting a saved setting
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1Press MENU.
2Press ß/© to select “Fine Sync”.
3Press ∂/ƒ to select “Select Setting”, and then
press ©.
4Press ∂/ƒ to select the desired memory setting.
5Press ENTER to select the setting.
6To exit from the GUI, press MENU.
•If a memory position has not been set, a resolution and
frequency setting will not be displayed.
•When selecting the stored adjustment setting with “Select
Setting”, the computer system should match the stored
setting.
(GUI) On-screen Display
2
3
MOUSEADJ.
Projector Remote Control
1.2.3 4.5.6
1, 6
5 2, 3, 4
3
MOUSEADJ.    
						

							E-48
Basic Operation
Adjusting the Computer Images (RGB menu only)
Special Mode Adjustment
Ordinarily, the type of input signal is detected and the
correct resolution mode is automatically selected.
However, for some signals, the optimal resolution mode
in “Special Modes” on the “Fine Sync” menu screen
may need to be selected to match the computer display
mode.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1Press MENU.
2Press ß/© to select “Fine Sync”.
3Press ∂/ƒ to select “Special Modes”, and then
press ©.
4Press ∂/ƒ to select the optimal resolution mode.
5Press ENTER to save the setting.
6To exit from the GUI, press MENU.
•Avoid displaying computer patterns which repeat every
other line (horizontal stripes). (Flickering may occur, making
the image hard to see.)
•When inputting DTV 480P or 1080i signals, select the
corresponding type of signal in step 4 above.
Projector
(GUI) On-screen DisplayRemote Control
MOUSEADJ.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1Press MENU.
2Press ß/© to select “Fine Sync”.
3Press ∂/ƒ to select “Signal Info” to display the
current input signal.
4To exit from the GUI, press MENU. This function allows you to check the current input signal
information. ProjectorMOUSEADJ.
Remote Control
1.2.3 4.5.6
1, 6
5 2, 3, 4
1.2.3 4.5.6
1, 4
2, 3
(GUI) On-screen Display
Checking the Input Signal   
						

							E-49
Basic Operation
Adjusting the Computer Images (RGB menu only)
Auto Sync Adjustment
•Used to automatically adjust a computer image.
•Auto Sync adjustment can be made manually by
pressing AUTO SYNC, or automatically by setting
“Auto Sync” to “ON” in the projector’s GUI menu.
When “Auto Sync” is set to “ON”:
•The sync adjustment is automatically made each time
the projector is turned on while connected to a com-
puter or the input selection is changed.
•The Auto Sync adjustment setting previously made is
cleared when the projector’s setting is changed.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1Press MENU.
2Press ß/© to select “Fine Sync”.
3Press ∂/ƒ to select “Auto Sync”.
4Press ß/© to select “ON”.
5To exit from the GUI, press MENU.
•Automatic adjustments can be made by pressing AU TO
SYNC.
•When the optimum image cannot be achieved with Auto
Sync adjustment, use manual adjustments. (See page 46.)
During Auto Sync adjustment, the On-screen Display
changes as shown on the left.
•Auto Sync adjustment may take some time to complete,
depending on the image of the computer connected to the
projector.
(GUI) On-screen Display Projector
g
sf
On-screen Display
Auto Sync Display Function
Normally, an image is not superimposed during Auto
Sync adjustment. You can, however, choose to
superimpose a background image during Auto Sync
adjustment.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1Press MENU.
2Press ß/©  to select “Fine Sync”.
3Press  ∂/ƒ  to select “Auto Sync Disp”.
4Press ß/© to select “
” to superimpose a
background image or “
” to remove the
background image during Auto Sync adjustment.
5To exit from the GUI, press MENU.
MOUSEADJ.(GUI) On-screen Display
Remote Control
1.2.3 4.5.6
2, 3, 4
1, 5
AUTO SYNC
button
MOUSEADJ.