Sharp Xr10xl Manual

7
Introduction
15. OverloadingDo not overload wall outlets, extension cords, or
integral convenience receptacles as this can
result in a risk of fire or electric shock.
16. Object and Liquid EntryNever push objects of any kind into this product
through openings as they may touch dangerous
voltage points or short-out parts that could result
in a fire or electric shock. Never spill liquid of any
kind on the product.
17. ServicingDo not attempt to service this product yourself as
opening or removing covers...

8Observe the following safeguards when setting up your
projector.
Caution concerning the lamp unit

Potential hazard of glass par-
ticles if lamp ruptures. In
case of lamp rupture, contact
your nearest Sharp Autho-
rized Projector Dealer or Ser-
vice Center for replacement.
See “Replacing the Lamp” on
page 52.
Caution concerning the setup of the pro-
jector

For minimal servicing and to maintain high
image quality, SHARP recommends that this
projector be installed in an area free from
humidity, dust and...

9
Introduction
When turning off the projector, the cooling fan
runs to decrease the internal temperature for
a while. Unplug the power cord after the cool-
ing fan stops. The period the cooling fan runs
will vary, depending on the circumstances and
the internal temperature.
Caution regarding usage of the projector

When using the projector, take care not to
subject it to hard impact and/or vibration, as
this can result in damage. Take extra care with
the lens. Before moving the projector, make
certain...

10
Accessories
Remote control
RRMCGA398WJSATwo R-6 batteries
 (“AA” size, UM/SUM-3,
HP-7 or similar)
Power cord*RGB cable
(10' (3.0 m))
QCNWGA045WJPZ
• Operation manual (this manual (TINS-C689WJZZ) and CD-ROM (UDSKAA083WJZZ))
Optional accessories

3 RCA to 15-pin D-sub cable (10n (3.0 m))

DIN-D-sub RS-232C adaptor (5 57/64o (15 cm))

Remote receiver

Lamp unit
AN-C3CP2
AN-A1RS
AN-MR2
AN-XR20L2 (for XG-MB65X-L/XG-MB55X-L)
AN-XR10L2 (for XR-10X-L/XR-10S-L)
Supplied accessories
For U.S. and
Canada,...

11
Introduction
31
37
50
30
30
28
29
47
28
15
27
27, 50
37, 46
27, 50
37
Top View
STANDBY/ON
button
For turning the
power on and
putting the
projector into
standby mode.Lamp indicator
Temperature warning
indicator
Adjustment buttons
(P/R/O/Q)
For selecting menu items.Volume buttons
(–O/Q+)
For adjusting the speaker
sound level.
ENTER button
For setting
items selected
or adjusted on
the menu.
MENU/HELP button
For displaying
adjustment and
setting screens, and
help screen.
Front View
Focus ring
For...

12
25
47
29
26
25
25
24
23
24
25
21
23
24
26
24
43
47
Numbers in Z refer to the main pages in this operation manual where the topic
is explained.
Terminals
Rear View
Refer to “INPUT Terminals and Connectable Main Equipment” on page 21.
AUDIO (INPUT
3, 4) terminal
(Shared for
INPUT 3 and 4) INPUT 3 terminal
Terminal for connect-
ing video equipment
with an S-video
terminal.
INPUT 4 terminal
Terminal for
connecting video
equipment.
Speaker
Rear adjustment
footKensington Security
Standard connector
AC...

13
Introduction
31
37
30
34
30
37
46
2727
37
34
34
37
30
34
32
Numbers in Z refer to the main pages in this operation manual where the topic
is explained.
STANDBY button
For putting the
projector into the
standby mode.
KEYSTONE button
For entering the
Keystone Correction
mode.
RETURN button
For returning to the
previous menu screen
during menu operations.
FORWARD/BACK
buttons
Same function as the
[Page Down] and [Page
Up] keys on a computer
keyboard when using the
optional Remote Receiver
(AN-MR2).
BREAK...

14
• Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
• Insert the batteries making sure the polarities correctly match the m and n marks inside the battery
compartment.
• Batteries of different types have different properties, therefore do not mix batteries of different types.
• Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
• Remove the batteries from the remote control once they have...

15
Introduction
• The signal from the remote control can be re-
flected off a screen for easy operation. How-
ever, the effective distance of the signal may
differ depending on the screen material.
When using the remote control
• Ensure that you do not drop it or expose it to
moisture or high temperature.
• The remote control may malfunction under a
fluorescent lamp. In this case, move the pro-
jector away from the fluorescent lamp.
Usable Range
The remote control can be used to control the
projector...

16
Quick Start
This section shows the basic operation (projector connecting with the computer). For details, see
the page described below for each step.
Setup and Projection
In this section, connection of the projector and the computer is explained using one example.
When connecting equipment other than a computer, see
pages 24 and 25.
3. Remove the lens cap and turn the projector on 2. Connect the projector to the computer and plug the power cord
into the AC socket of the projector
On the projector On...