Sim2 Multimedia Domino D80 Projector User Manual

11

SwiTChiNg Off AND RETURNiNg TO STANDBY
With the remote control: press  .
With the keypad: press .
When switching off, the projector goes into stand-by mode and 
stores the input selection at the time of switch-off.
The  fans  keep  running  until  the  lamp  cools  down  (green  and 
red leds on), after which they automatically switch off. Do not 
switch off the projector with the power switch until the fans have 
stopped running.  
6  CONNECTiONS
To obtain the best performance from your projector,...

1

D80 - Connection panel 
31245
Television receiver
DVD player
VCR
Videocamera
Video game console
Television receiver
HDTV receiver
DVD player
VCR
Video game console
ComputerDVD player
HDTV receiver
Fig.16
6
                   
       
                             
                     
     8
    
     (
   
 
ATTENTION: pour ne pas compromettre la protection contre les resque dincende remplacer par un fusible de meme type et de mems CAUTION: for continued protection
 against 
risk of fire,...

1

of the pictures reproduced by the D80 in the two cases:  the 
deinterlacing  performed  by  the D80  is  often  more  effective 
than that performed by the source itself.
gRAPhiCS RgB
This input should be connected to an RGB-type video or graphic 
signal using a cable with a DB15HD type connector.
The signal source device (typically a personal computer or game 
console) must be able to provide separate H/V synchronisation or 
composite H+V synchronisation.
hDMi™
HDMI™  (High  Definition...

14

RS232 iNTERfACE CONNECTOR 
The projector can be controlled from a PC: simply hookup 
the interface connector to a PC ’s RS serial cable.
Do  not  place  objects  between  the  remote  control  and  the 
receiver on the projector, as this can prevent the remote from 
working.
DVIC -S YN C
MOTORiSED SCREEN OUTPUTS
' ,* ,7$ /,1 3 8 7$8 ' ,22 8 7= 2 2 0& 2 1 7 52/   5 6         * 5 $ 3+ ,& 6 5 * %5  & U*  

15

MAiN MENU
To  access  the  main  menu  of  the  On  Screen  Display  press 
the MENU key on the keypad or the MENU+ or MENU- key on the 
remote control. 
The  main  menu  is  divided  into  four  windows, PICTURE,  IMAGE, 
SETUP  and  MENU,  in  which  the  various  adjustments  are  grouped 
according to the frequency of use. Use the ▲ and ▼ keys to 
select  the  line  corresponding  to  the  adjustment  you  wish  to 
make (Fig. 1). 
The  various  menus  only  offer  the  relevant...

16

To  access  these  submenus,  press  the  

17

NORMAL:  projects  the  image  occupying  the  full  height  of  the 
screen  while  maintaining  the  aspect  ratio  of  the  input  signal. 
When the input signal aspect ratio is 4: black vertical bands 
are displayed on the right and left of the picture.
ANAMORPHIC: correctly displays a 16:9 image.
LETTERBO x: serves to display a 4: letterbox image (with source 
signal having black bands above and below the picture) so that 
it fills the 16:9 screen and maintains the correct aspect...

18

There  are  4  sets  of  gamma  curves:  Standard  (ST),  Enhanced SIM  (EN)  and  Graphics  (GR),  User.  The  Standard  curve  has been  defined  for  general  use,  and  is  set  for  videocameras, digital cameras, and for viewing films or photos on your PC. The Enhanced set is suitable for watching movies. The Graphics set is suited to displaying synthetic graphics (PC, CAD, PC presenta-tions, etc.). User enables you to define your own curve. You can thus select the coefficient which...

19

Values from 1.5 to .  allow you to emphasise the detail of dark images,  but  reduce  overall  contrast.  Values  higher  than  . increase overall contrast, but reduce the detail of dark areas. 
For the most common video sources, the  overscanning value 
can be in the range (no overscanning) to  (maximum). The 
resulting image always maintains the selected aspect irrespec-
tive of the selected overscan value. 
POSiTiONUse this adjustment to position the image vertically...

0

TEST PATTERNS
Displays  a  series  of  five  test  patterns,  which  are  useful  when 
installing the system and checking basic functions. Use the ◀ 
and ▶ keys to browse through the test patterns (Fig. 7). 
iNiTiAL SETTiNgS
Reconfigures  the  projector  to  original  factor y  settings  except 
Position, Orientation, Y/C Delay, Zoom and Focus (Fig. 8).
MENUS
LANgUAgE
It  allow  to  select  the  languages  available  for  the  On  Screen 
Display menus.
iNPUTS LiST
In order to make...