Sim2 Multimedia Domino D80e Projector User Manual

460.554.000
D80

2
Sets the unit to stand-by.
Activates the On Screen Display menus and 
allows navigation though the various pages. ▲,▼
,◀,▶
Navigates between the On Screen 
Display menus and parameter settings.
Calls up the  
Source Selection menu.
Deactivates the On Screen Display
1  REMOTE CONTROL AND KEYPAD
KEYS 0-9
Select the sources directly. 
Switches on the panel from Standby.
STAND-BY / ON
Sets the panel to stand-by .
ESCAPE
Deactivates the On Screen Display.
UP/DOwN/LEfT/RighT ARROw KEYS
Navigates between the...

3
Different input signal resolutions can be adapted to match the specified 
screen  resolution  without  loss  of  image  quality,  thanks  to  a  generous 
selection of preset aspect ratios, some of which are user definable.
All picture adjustments can be made with the remote control interac-
ting  with  a  simple  menu-activated  On  Screen  Display;  alternatively, 
the  projector  can  be  controlled  by  a  domestic  automation  system 
via its serial port.
The appliance has been subjected to...

4
CAUTiONTo reduce the risk of electric shock, disconnect the power supply cable on the rear panel before removing th\
e top cover of the projector.
For technical assistance refer to trained personnel authorised by the man\
ufacturer.
Read  all  chapters  of  this  manual  carefully  before  switching  on  the  projector.  This  manual  provides  basic  instructions  for  using  the  D80E 
system. installation, preliinary adjustments and procedures that necessitate the removal of the top cover and...

5
fCC STATEMENT
CLASS B PRODUCT
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These 
limits  are  designed  to  provide  reasonable  protection  against  harmful  interference  in  a  residential  installation.  This  equipment  generates,  uses 
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to 
radio communications....

6
  
    
 
      
      
       
                                      
     8
    
     (
  
     
             65; 8 4+ 6 9 ) 53 6853 +::8+ 
2  685:+) :/54 ) 54:8+ 2+9 8+97; + *   /4) +4* + 
8+3 62 ) +8 6 8 ; 4 ,; 9/( 2+ * + 3 +3 + :?6+ 
+: * + 3 +3 9 )  8  ) :+8/9: /7 ; +          ,58 ) 54:/4 ; +*  685:+) :/54  -  /4 9: 
8 /91 5, ,/8+   8+62 ) + 
542? = /:.  9 3 + :?6+ 
 4*  8  :/4-  ,; 9+  
        
 
  
  
  
  
  
    
    
12
3
6 7
4 5
8
9
10
20 12
11
13
17
18 14
15
16
19 19
•  
Read this manual...

7
•  Changing the fuses.
  Before changing the fuse disconnect the unit from the 
mains power supply.
  The  fuse  compartment  is  next  to  the  power  supply  con-
nector (Fig. 3). Remove the fuse holder (2) with a flat head 
screwdriver and replace the fuse (3). Fit a new spare fuse 
(4). Use only T 3,15 A H fuses.
Fig.3
•   Be careful with cables.
  Make certain cables are routed so that people will not be 
impeded or tripped up.
  Keep all cables away from children. 
  Install the unit as close to...

8
3  UNPACKiNg
To remove the D80E system from its carton follow the diagrams (Fig. 4).
Keep the carton for use when transporting or shipping the unit.Fig.4
CONTENTS Of PACKA
gE
User and 
installation manual
Remote control 
1,5 AA batterie s Po
wer cables 
EU , UK , US
Pr
ojector
Fig.5
- the projector
- Remote control 
- four 1.5V AAA batteries (for remote control)
- three power cables (EU, UK, USA) for the projector
- the user manual.
- Additionals feets
If anything is missing, immediately inform your...

9
Position the projector on a stable, suitable platform or utilise the 
optional bracket for a fixed ceiling installation.
ATTENTiON:  in case of floor mounting, read carefully the sa-
fety instruction "w arning on floor mounting" at chapter 2.
w ARNiNg:  if  using  the  ceiling  mount  bracket,  scrupulously 
observe  the  safety  instructions  included  with  the  bracket 
itself.  if  using  a  bracket  other  than  that  supplied  by  SiM2 
Multimedia, make sure that the projector is at least...

10
To  activate  an  electric  motorised  screen  a  12  Volt  output  is 
provided at the rear of the projector (Fig. 10).
The output is activated (Voltage: 12 Vdc) when the projector is 
switched on and is de-activated (no Voltage output) when the 
projector is in stand-by mode.
You can also use black motirised curtains to delimit the screen 
when the projected image aspect ratio changes (Fig. 11a). This 
option is controlled via the output at the rear of the projector. 
For rear projection the screen...