Sim2 Multimedia Grand Cinema C3x Projector User Manual

							
1

+12VUSB 1. 1R/CrCONTRO L (RS 232)GR APH IC S RGBC/YB/CbHVS-VIDE OAUDIO OUTHDMI 1REMOTE32S-VIDEOMENUESCIN PUT1540I
ZOOM
ZOOM
ZOOM
ZOOM
F1
FOCUSAUTO ASPECTVCR
HELP ZOOM
F2
ZOOM
FOCUSFOCUSFOCUSFOCUS

Fig. 8
In the initial phase of installation the configurable keys (F1, F) 
serve as optical zoom and optical focus (Fig. 8).
LAMP POWER
If your room is especially dark, the images from the system  c3X 
could  result  execessively  bright.  In  order  to  enjoy  wonderful 
images,  the EcOMODE  function  activation  allows  to  re  du  ce 
the power used to feed the lamp. In this way, the brightness of 
the image will be adapted to your projection conditions and 
a grater life lamp will be guaranteed.
POWER ON
If active (AUTO) allows to power up the system directly from the 
power feeder, once the initializing phase is completed.
If not active (STAND-BY) once the initializing phase is completed 
the system remains in a stand-by mode waiting to receive the 
power on command from the remote control or the key pad.
TEST PATTERNS
Displays a series of five test patterns, useful for the installation 
of the projector.
Press ◀ and ▶  keys to browse pattern.
FACTORY DEFAULTS
Reconfigures  the  projector  to  original  factor y  settings  except 
Position, Orientation, Y/c Delay, Zoom and Focus (Fig. 9).
No
    Confirm?
Yes
ON SCREEN MENU
LANGUAGE
Lists the languages available for the On Screen Display menus.
SOURCE LIST
In order for the  c3X system to be more flexible, the following 
described functions allow to modify the input selection menu 
making it more user friendly.
The main window shows all the inputs available on the Projector. 
If one or more inputs are not utilized, it is often helpful to blank 
them from the input list (accessed with the 0 key).
Once the input has been chosen, in the drop menu that ap-
pears by pressing the ◀ key, it is possible to activate the source 
(Fig. 30). 
The exclusion or activation of the source will automatically 
renumber the remaining active inputs.
2  S-VIDEO   
4  GRAPHICS RGB 3  COMPONENT / RGBS   
1  VIDEO    1234
S-VIDEO 3    
GRAPH RGB 9 COMP RGB 5 
VIDEO 1    
55HDMIHDMI 5
Source list/Edit source name
ACTIVA  
NAME
Yes No
Fig.30
The inputs with an active video signal (visible in the input selec-
tion menu) are marked with a check symbol.
It can be also helpful to identify the input with a name chosen 
by  the  user  (for  example  with  the  name  of  the  connected 
source) rather than with the signal type.
Once chosen to have the input visible, in the drop menu, by 
selecting the Name option it is possible to rename the source 
in use.
This will make it easier to remember the source connected to 
Fig. 9 
						

							


a  specific  input.  You  can  use  up  to  1  alphanumeric  letters 
to  name  the  source  (for  more  details  check  the  “Insert  text ” 
section). 
INSERT TEXT
You will be able to insert text easily and rapidly by accessing 
the text insertion menu (fig. 31).
#ANCEL
#ONFIRM
%DITSOURCENAME	 !#$%&
()*+,-./
0123

456

789:
???????????
Fig.31
The text insertion mode remains the same if text is being inserted 
for  the  first  time  or  if  a  previously  inserted  name  is  being  edi-
ted. The letter insertion can be done in any available position 
(represented by horizontal lines). Use the ◀ and ▶ keys to move 
between letters either left or right respectively.
Press the numeric key matching the letter (Fig. 3), the first click 
of  the  key  selects  the  first  letter,  the  second  click  the  second 
letter and so on.
The available letters are shown in the text insertion menu.
Once one letter has been inserted, to insert the following one 
it is necessar y to move with the cursor in the next right position 
with the ▶ key of the remote control, repeat this procedure to 
insert other letters. 
Use the ▲ key to switch from small case to capital letters and 
viceversa.
Any mistake can be deleted with the ▼ key once it has been 
positioned on the wrong letter.
Once the text insertion process is finished, it can be confirmed 
and saved by clicking the MENU+ key.
If you want to delete the modifications use the MENU- key of the 
remote control.
F1/F2 KEYS
This  allows  to  assign  different  functions  to  the  remote  control 
keys, named F1 and F.
The window is made of 6 options, once for each line and by 
two columns showing the F1-F keys. The choice between F1 
and F is made by the ◀ and ▶ keys of the remote control; the 
function given to F1 and F is chosen with the ▼ and ▲ keys.
The function delivered by the key is memorized by the inter-
section on the line and column.
In the following window are described the 6 options
Fig.3
Zoom
Allows to access the optic zoom, where the ◀ and ▶ keys allow to increase or decrease the size of the projected image.
Focus
Once selected, the ◀ and ▶ keys allow to focus the image.MagnificationAllows you to select the area to be viewed and then magnify the projected image. The degree of enlargement is selected in Zoom mode (identified by a magnifying glass in the centre 
of the image) using the ◀ and ▶  keys. The area of the picture to be enlarged is selected  in Pan mode (symbol in the centre 
of  the  picture)  using  the   ◀,▶, ▼  and ▲      arrow  keys.  You  can toggle between Zoom and Pan mode by pressing the  F1/F 
key on the remote control. 
Blank
Blanks the active video signal producing a completely black 
screen. Once pressed the key an indication of a few seconds 
on the OSD will confirm its activation. A click of any other key of 
the remote control allows to restore the previous settings.
Color temperature
The following click of the key (F1 or F) allows to choose between 
the different color temperatures available. HIGH , MID , LOW , USER .
Source list
F1/F2 keys
Source info
OSD Backgroung
OSD Position
OSD Timeout
Language
-ENU
English
Zoom
Focus
Magnification
Blank
Colour temperature
Gamma correction
F1F2 
						

							
3

Gamma correction
The following click of the key (F1 or F) allows to choose between 
the different gamma curves available.
 
SOURCE INFORMATION
When active (YES) each source change will show the information 
related to the signal. If not active (NO) there will be no information 
on the selected source..
OSD BACKGROUND
Determines  the  type  of  background  for  the  On  Screen  Di-
splay.
OSD TIMEOUT
Use this adjustment to set the display time after which the On 
Screen Display will disappear.
OSD POSITION
Allows  the  On  Screen  Display  to  be  positioned  in  a  particular 
area of the projected image. The OSD can be positioned using 
the arrow keys for fine adjustments or keys 1...9 on the remote 
control to select one of 9 preset positions.
MEMORIES
The main parameters of the image may be saved in distinct 
groups  of  values  (known  as  ‘Memories’);  these  parameters 
can  subsequently  be  applied  all  together  by  way  of  a  single 
command.
There are 3 distinct Memories (Memor y 1, Memor y  , Memor y 
3)  for each of the 5 signal types managed:
making a total of 75 different available Memories.
The  image  parameters  that  can  be  saved/recalled  by  the 
Memories management system are the following:
Image Picture
BRIGHTNESS  ASPEcT
cONTRAST cOLOR TEMP.
cOLOR OVERScAN
TINT GAMMA
SHARPNESS 
FILTER 
SHARPNESS MODE
VIDEO TYPE Setup
NOISE REDUcTION LAMP POWER
Some  of  these  parameters  may  not  be  available  for  certain 
inputs or certain input signals, as indicated in Tables 4 and 5.
The  menu  page  for  the  Memories  management  functions  is 
activated by pressing the   key on the remote control or the  
◀ key on the keypad (Fig. 33).CONTROL (RS232)
GRAPHICS RGBB/CbHVS-VIDEO
AUDIO OUT
HDMI 1
REMOTE
2S-VIDEO
MENU
ESCINPUT
1
5
4
0I
Fig.33 
						

							
4

The operations that can be performed on each memor y se-
lected are described here below.
Save a memory
To save the current values of the image parameters in Memor y 
1, use the ▼ and ▲ keys to move to line ‘1’ and then open the 
pull-down menu by pressing the  ◀  key (Fig. 34). Then select 
the option ‘Save current settings’. To confirm that the operation 
has been completed successfully, the message current settings 
saved in Memory 1 is displayed at the bottom of the screen and 
the letter ‘S’ appears to the left of the memor y name. The same 
procedure is used to save parameters in Memories  and 3.
0  Auto
3       S   MEMORIA 1
-EMORIES
Save current settings
Save initial settings
Rename
2        I   
1       S   
Fig.34
Recall a memory
To  recall  a  Memor y,  select  the  desired  line  and  press ▶.  The 
parameters saved in the selected Memor y will be applied to 
the  image  displayed  and  a  message  will  appear  to  confirm 
the  operation  Memor y  1  recalled.  The  Memor y  recalled  will 
be  associated  with  the  source  and  signal  type,  and  will  be 
automatically  recalled  ever y  time  that  particular  source  and 
signal type combination is selected.
Save default settings
To restore the original values to a previously modified Memor y, 
select the line corresponding to the Memor y in question and 
open the pull-down menu ( ◀ key). Then select the line  Initial 
settings saved in Memor y 1. To confirm that the operation has 
3  COMP/RGB(YCrCb 15KHz) 3  COMP/RGB(RGB 15KHz) 
4  COMP/RGB(YCrCb 32KHz) 4  COMP/RGB(RGB 32KHz) 
6  HDMI
1  VIDEO    
5GRAPHICS RGB 
2  S-VIDEO     
been  completed  successfully,  the  message  Memor y  1  ini-
tialised is displayed at the bottom of the screen and the letter 
‘I’ appears to the left of the name of the memor y.
Rename a memory
It  is  possible  to  assign  a  name  to  each  Memor y.  To  assign 
a  name  (with  a  maximum  length  of  1  alphanumeric  char-
acters)  to  a  Memor y,  select  the  option  ‘Rename’  from  the 
corresponding  pull-down  menu.  Enter  the  text  following  the 
procedure indicated in paragraph SOURcE LIST.
Restore Current Settings
On entering the MEMORIES menu, a copy of the current settings 
is saved in a temporary menu (labelled with 0 - AUTO). Once one 
or more memories have been recalled, you can restore the 
settings that were effective at the moment the Memories menu 
was  accessed  by  selecting 0  -  AUTO.  However,  this  operation 
must be completed before the  MEMORIES menu page disap-
pears (30 seconds after the last operation commanded from 
the remote control or the keypad). The next time it appears, 
the temporar y memor y will contain new information that takes 
into account any Memories selected the penultimate time the 
‘Memories’ page was accessed.
Memor y  0  (-  AUTO)   can  be  used  even  when  you  do  not  wish 
to enable the Memories management function for the signal 
currently in use. Once Memor y 0 has been selected, when a 
source is chosen, the settings that were effective at the time 
the    Memor y  was  previously  recalled  will  be  automatically 
applied.  
INFO
Displays  the  current  status  of  the  projector  and  information 
concerning the projected video/graphic signal.
This function is displayed on pressing   on the remote control 
(or, in the absence of the On Screen Display, the ▶ key on the 
remote control). 
						

							
5

QUICK MENUS
The  quick  menus  provide  access  to  the  main  adjustments 
that affect image quality, without calling the main On Screen 
menus. 
BRIGHTNESS, cONTRAST , cOLOUR , TINT , SHARPNESS and FILTER adjustments 
appear at the bottom of the screen one after the other when 
the ▼ and ▲  keys are pressed .
MESSAGES
The following messages may appear during operation of the 
system:
No signal
The system does not recognise any signal applied to the se-
lected input. In this case:
•  Make  sure  the  selected  input  is  connected  to  a  video  or 
graphic  signal  and  that  that  source  is  functioning  cor-
rectly.
•  check  the  condition  of  the  cables  used  to  connect  the 
system to the various sources.
•  Make sure the video or graphic signals supplied by the sour-
ce are compatible with the system’s technical specifications 
and, in particular, with those of the selected input.
Out of range
This message appears when either the resolution or the vertical/
horizontal frequency of the input signal exceeds  c3X specifica-
tions (e.g. a QXGA graphic signal) or when an input is supplied 
with an incompatible signal (e.g. after setting the components 
input to YPrPb 15kHz a progressive signal is connected).
Substitution lamp
If  the  lamp  hours  exceed  the  90%  of  the  life  lamp,  at  ever y 
switching on , a brief message appears on the screen to re-
member the need of replacing it in a short time.
If  the  lamp  life  is  greater  than  100%    the  message  above 
persists until the ESc key is pressed. 
						

							
6

11  TROUBLESHOOTING GUIDE
No power  (Green and red LED are OFF) 
• check the power switch at the rear: it must be in position I.
• check if the power cable has been connected correctly to 
a working socket.
• check the power socket fuse, at the rear of the projector.
• Replace the fuse on the mains socket with an identical type  
(T 5A H ) (Fig. ). (Fig. ). 
• Should  the  problem  persist,  seek  authorised  technical  assi-
stance.
The lamp is not coming on
• Allow a few minutes pause between switching off and turning 
on again (from stand-by). This will allow the lamp to cool down 
sufficiently.
• If the lamp doesn’t come on – even though the projector has 
had sufficient time to cool down – seek technical assistance 
from your nearest Dealer.
No image
• check  that  the  selected  input  is  actually  connected  to  a 
active video or graphic signal.
• check that the above source actually works. 
• Verify compatibility of video/graphic signals with the   technical 
specifications of the projector.
• check the integrity of cables used to connect various sour-
ces.
• c heck  the  cooling  air  inlets  or  air  outlets  on  the  units  are 
not  obstructed  and    the    room  temperature  is  below  35°c 
(95°F).
Image is disturbed, unstable or noisy
• Verify compatibility of video/graphic signals with the technical 
specifications of the  projector.   
• check the integrity of cables connecting projector to various 
sources.
• If the signal source is a terrestrial broadcast (via a Vc R) check 
that the receiving channel has been correctly tuned in and 
that the aerial system is in good working order. 
• Should the problem be present with a signal coming from a 
video-recorder, ensure that the videotape is an Original “ first 
generation” copy and in good condition. 
• Adjust  the  VcR’s  tracking  control  for  optimum  picture  per-
formance.  Ensure  the  VcR  mode  is  active  in  the  Picture  
menu.
Incomplete image along borders (vertical and horizontal) 
• compare  compatibility  of  video/graphic  signals  and  tech-
nical specifications of your projector.   
• Press A on your remote control or AUTO on keypad to execute 
automatic adjustments.       
10  CLEANING AND MAINTENANCE
The Projector do not require internal cleaning.
There is no user serviceable parts inside the projector. 
Please refer all service requirements to qualified personnel.
Cleaning the projector ’s cover: 
Use  a  soft  slightly  damp  cloth.  Do  not  use  abrasive  cleaners, 
solvents  or  other  harsh  chemicals,  as  this  will  damage  the 
finish  of  the  cover.  Avoid  direct  cleaning  of  the  rear  panel’s 
screen-printing.
Cleaning the lens:
The lens may be cleaned with a ver y soft, non-abrasive small 
brush, in order to remove dust particles.  Alternatively, use a soft 
dr y cleaning cloth (of the type used for camera lens cleaning) 
to remove fingerprints and grease marks. 
						

							
7

You  can  purchase  the  following  optional  accessories  at  your 
Dealer:
 - ceiling Bracket Kit.
 - Type of lens
Up to six types of lenses are available to accommodate different 
throw  distances  and  your  specific    installations.  See ADDITIONAL 
INFORMATION    for  more  details  on  throw  distances  and  the    di-
mensions of  the image projected.  To change the lens,  contact 
always  your nearest dealer.
Use only original, or SIM Multimedia approved, accessories.
12   OPTIONAL ACCESSORIES
CAUTION: for ceiling installation, by means of suspension bracket, 
carefully  follow  the  instructions  and  safety  instructions  recom-
mended by the Manufacturer in the bracket’s literature.
Rivolgetevi  sempre  al  vostro  centro  di  assistenza  per  sostituire 
l’obiettivo.  Utilizzate  solo  accessori  originali  o  approvati  da SIM2 
Multimedia.
• Adjust the horizontal and vertical position of projected image 
by selecting  POSITION on the IMAGE ADJUSTMENTS menu.
• Adjust the width and height of image, selecting ASPEcT in the 
IMAGE ADJUSTMENTS menu.
• Adjust the Overscan value in the IMAGE/OVERScAN menu.
Image too dark, too pale or unnaturally coloured
• Verify  compatibility  of  video/graphic  signals  with  technical 
specifications of your projector.   
• Go to PIcTURE menu, select and regulate any of the following, 
accordingly: cONTRAST , BRIGHTNESS , cOLOR, and TINT.
• If necessary, reset the cOLOR  TEMPERATURE and G AMMA  cORRE cTION 
(found on the IMAGE ADJUSTMENTS / ADVANcED SETTINGS menu).
 Graphic image with poor quality vertical detail
 
• Verify compatibility of video/graphic signals with technical 
specifications of your projector.
• Press A on your remote control or AUTO on keypad to exe-
cute automatic adjustments.
• Adjust FREQUENcY and PHASE  parameters, found in the 
IMAGE ADJUSTMENTS menu, to optimise vertical detail of the 
projected image.
Video  Image  showing  colour  misalignment  on  ver tical 
details
• Verify  compatibility  of  video/graphic  signals  with  technical 
specifications of your projector.
•  Adjust Y/ c  D ELAY  settings  in  the IMAGE   ADJUSTMENTS   /  ADVAN cED 
SETTINGS  to  reduce  colour  misalignment.  For  best  results  use 
an external colour bar test pattern source.
Remote control does not work 
• check the batteries and for correct polarity.
• Ensure  that  the  area  between  the  infrared  sensor  (front  of 
projector) and the remote control is free of obstruction.
• Ensure  that  infrared  sensors  (front  and  rear  of  projector)  are 
not exposed to intense light levels. 
						

							
28

ELECTRICAL
Input signals:
 • 1 COMPOSITE VIDEO (CVBS)
       
    RCA type connectors, gold-plated 
       
    1,0 V
pp / 75 Ω, negative synchronisation
 
• 1 S-VIDEO (Y/C)
            
   
4-pin mini-DIN connectors
       
   
Y: 1,0 V
pp / 75 Ω,  negative synchronisation 
     
C: 0,286 Vpp / 75 Ω, [NTSC nominal burst level] 
     
0,3 Vpp / 75 Ω [PAL, SECAM nominal burst level]
 
• 1 COMPONENTI (Y/Pr/Pb/H/V) - RGBS  
     
1 set of 4 RCA connectors
   
- Components signal   
          
     
Y: 1,0 V
pp / 75 Ω , negative or 3-level synchronisation      
     
Pr,Pb:0,7 Vpp / 75 Ω
       
 
- RGB signal
 
         
     
R,B:0,7 V
pp / 75 Ω
         
     
G: 0,7 Vpp / 75 Ω , HV Sync                       
   
1,0 Vpp / 75 Ω ,negative or 3-level synchronisation    
     
TTL positive or negative, 0,3-5 Vpp / 1 kΩ 
 
• 1 RGBHV (analogue RGB)
      
    
female DB15HD connectors
         
     
R,B: 0,7 V
pp / 75 Ω
         
     
G:0.7 V
pp / 75 Ω , separate H/V Sync or H+V Sync                   
       
1.0 V
pp / 75 Ω , negative or 3-level synchronisation     
     
TTL positive or negative, 0.3-5 V
pp / 1 kΩ  • 1 HDMI™   
Control: 
  Remote control, via RS232 from PC or   
  home automation devices, USB 1.1
Horizontal frequency: 
  from 15 to 80 kHz (up to UXGA, 85 Hz)
Vertical frequency: 
  48 -100 Hz
Video standards: 
  automatically selected (PAL B, G, H, I, M,   
  N, 60, SECAM, NTSC 3.58 and 4.43)
High definition video: 
  ATSC HDTV (480p, 720p, 1080i,)
Graphic standards: 
  VGA, SVGA, XGA, SXGA, UXGA         
Deinterlacer: 
  Faroudja chipset, DCDi™, 3:2 pull-down   
sequence conversion
Colour temperature: 
 
from 6500 to 10000 K
Outputs: 
 
-   2  12-V  jack  connector  outputs  (1  active 
with system powered on, 1 active with 
 
16:9 aspect ratio selected)
 
-  1  Optical  S/PDIF  audio  output  Toslink  con-nector
GENERAL PROJECTOR
Power supply cable:
  
(EU, UK e US); lenght 2m
Supply: 
 
da 100 a 240 Vac, tolerance +/- 10% 
 
frequency from 48 to 62 Hz
Consumption:  350 W max (240 W Max C3X LITE)Fuse:   T 5 A H, 5 x 20 mmDimensions of projector:   435x190x430 mm (LxAxP) Weight of projector:  11 kgOperation temperature:   10 to 35°CTransportation temp.:  -15 to 55°CStorage temperature: -15 to 55°CHumidity:   20% a 95% humidity non-condensingSafety:   EN 60950Transportability:   desktop equipmentCompatibility:  EN 55022 Class B
  EN 55024
  EN 61000-3-2
  EN 61000-3-3
Transportation: IEC 68-2-31, IEC 68-2-32
A  T EC h NICAL  s PECI f ICATION s 
						

							
9

B  ON SCREEN MENU LAYOUT
BrightnessContrastColorTintSharpnessFilterCinema Mode Video Type
Video • S-Video[NTSC]YCrCb15kHzRGBS  15kHz
RGBSRGB GraficoHDMI™
OrientationKeystoneLens
Power ONTest patternsInitial settings
Lamp Power
FloorFloor-rearCeilingCeiling-rear
NormalAnamorphicLetterboxPanoramicPixel to PixelUser 1User 2User 3
HighMediumLowUser
HorizontalVerticalScreen control
HorizontalVerticalScreen control
HorizontalVerticalScreen control
Red OffsetGreen OffsetBlue OffsetRed GainGreen GainBlue Gain
BrightnessContrastSharpnessSharpness Mode 
BrightnessContrastColorTintSharpnessSharpness Mode 
BrightnessContrastColorSharpnessFilterCinema Mode Video Type
Noise reductionNoise reduction
Video • S-Video[PAL, SECAM]
AspectColor TemperatureGamma CorrectionOverscan
HDMI™
AspectColor TemperatureGamma Correction Overscan
PositionY/C Delay
AspectColor Temperature
Gamma Correction OverscanPosition
AspectColor TemperatureGamma Correction
PositionFrequencyPhase
Video • S-VideoYCrCb  15kHzRGBS  15kHz
YCrCb
YCrCbRGBRGB  Grafico
 Image
 Setup
 Picture
AspectColor Temperature
Graphic NTSCNTSC EnhGraphic Enh
PAL SECAMPAL SECAM Enh
Gamma Correction
HorizontalVerticalZoomFocusLens ShiftAutoStand-by
LanguageSource listF1/F2 keysSource infoOSD backgroundOSD PositionOSD Timeout
Menu
ZoomFocuaMagnificationBlankColor temperatureGamma correction
Yes    No
ItalianoEnglish
Français
EspañolDeusch
Português
2  S-VIDEO 
4  GRAPHICS RGB3  COMPONENT / RGBS 
1  VIDEO1
234
S-VIDEO 2
GRAPH RGB 4COMP RGB 3
 5  5HDMIHDMI 5
F1F2
Active  Yes   No
Name
Cancel
Confirm
Edit source name ()?@1 ABC2 DEF3
GHI4 JKL5MNO6PQRS7-
+
 TUV8
0
WXYZ9
_ _ _ _ _ _ _ _ _ _ _
Not active       Auto      Manual
Flesh tone correction        On    OffFlesh tone correction        On    Off
Value
Overscan
Memories
Cancel
Confirm
Edit memory name ()?@1 ABC2 DEF3
GHI4 JKL5MNO6PQRS7-
+
 TUV8
0
WXYZ9
_ _ _ _ _ _ _ _ _ _ _
0  Auto
3    S   MEMORY  3
Memories
2    S   MEMORY  2   1    S   MEMORY 1Save current settingsSave initial settingsRename
VIDEO 1 
						

							
30

BrightnessContrastColorTintSharpnessFilterCinema Mode Video Type
Video • S-Video[NTSC]YCrCb15kHzRGBS  15kHz
RGBSRGB GraficoHDMI™
OrientationKeystoneLens
Power ONTest patternsInitial settings
Lamp Power
FloorFloor-rearCeilingCeiling-rear
NormalAnamorphicLetterboxPanoramicPixel to PixelUser 1User 2User 3
HighMediumLowUser
HorizontalVerticalScreen control
HorizontalVerticalScreen control
HorizontalVerticalScreen control
Red OffsetGreen OffsetBlue OffsetRed GainGreen GainBlue Gain
BrightnessContrastSharpnessSharpness Mode 
BrightnessContrastColorTintSharpnessSharpness Mode 
BrightnessContrastColorSharpnessFilterCinema Mode Video Type
Noise reductionNoise reduction
Video • S-Video[PAL, SECAM]
AspectColor TemperatureGamma CorrectionOverscan
HDMI™
AspectColor TemperatureGamma Correction OverscanPositionY/C Delay
AspectColor TemperatureGamma Correction OverscanPosition
AspectColor TemperatureGamma Correction
PositionFrequencyPhase
Video • S-VideoYCrCb  15kHzRGBS  15kHz
YCrCb
YCrCbRGBRGB  Grafico
 Image
 Setup
 Picture
AspectColor Temperature
Graphic NTSCNTSC EnhGraphic EnhPAL SECAMPAL SECAM Enh
Gamma Correction
HorizontalVerticalZoomFocusLens ShiftAutoStand-by
LanguageSource listF1/F2 keysSource infoOSD backgroundOSD PositionOSD Timeout
Menu
ZoomFocuaMagnificationBlankColor temperatureGamma correction
Yes    No
ItalianoEnglish
Français
EspañolDeusch
Português
2  S-VIDEO 
4  GRAPHICS RGB3  COMPONENT / RGBS 
1  VIDEO1234
S-VIDEO 2
GRAPH RGB 4COMP RGB 3
 5  5HDMIHDMI 5
F1F2
Active  Yes   No
Name
CancelConfirm
Edit source name ()?@1 ABC2 DEF3GHI4 JKL5MNO6PQRS7-+
 TUV8
0
WXYZ9
_ _ _ _ _ _ _ _ _ _ _
Not active       Auto      Manual
Flesh tone correction        On    OffFlesh tone correction        On    OffValue
Overscan
Memories
CancelConfirm
Edit memory name ()?@1 ABC2 DEF3GHI4 JKL5MNO6PQRS7-+
 TUV8
0
WXYZ9
_ _ _ _ _ _ _ _ _ _ _0  Auto
3    S   MEMORY  3
Memories
2    S   MEMORY  2   1    S   MEMORY 1Save current settingsSave initial settingsRename
VIDEO 1