Singer Professional 5 Manual

							 
 
 
 
 
 
 
 
 
 
 
 
 
      
 
                         
 
 
 
 
 
 
 
 
                                 
 
 
 
 
 
 
 
 
 
 
 
  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
      
 
                         
 
 
 
 
 
 
 
 
                                 
 
 
 
 
 
 
 
 
 
 
 
 
 
 Three-Thread Overlock (narrow) page 4   
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
      
 
                         
 
 
 
 
 
 
 
 
                                 
 
 
 
 
 
 
 
 
 
 
 
  
 
 
 
 
  
 
  
 

						

							 
   
   
 
Two-Thread Overedge (narrow) page 7
 
 
  

						

							 
  3. Thread the top cover thread guide by pulling the thread towards the left until 
       it slips under the guide.  Then pull the thread along the right side of the  
       button as illustrated.  
 
 
 
 
 
 
 
 
 
 
  4. While holding the thread, firmly pull the thread between the tension disks. 
 
 
  
 
 
 
 
 
 
 
 5. Turn the handwheel toward you until the lower looper extends 5-10mm  
       (approximately ½”) from the needle plate edge.   
 
  6. Thread the looper area of the machine following the green color coded  
       thread guides 4-9. 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
Three-Thread Overlock (narrow) page 8  
						

							 
 7. Thread the hole in the Upper Looper from front to back k.  Pull about 4  
                inches of thread through the looper and place to the back of the  
                throat plate. 
  
 
 
 
 
 
 
 
 
 
 
 
 
 

						

							 
   
  
 4. While holding the thread, firmly pull the thread between the tension disks. 
 
 
  
 
 
 
 
 
 
  
  5. Turn the handwheel toward you until the lower looper extends 5-10mm  
       (approximately ½”) from the needle plate edge.   
 
  6. Thread the looper area of the machine following the red color coded  
       thread guides 4-10. 
 
 
 
 7. Place the thread slighty from left and  
      to the right of threading guide f. 
 
 
 
 
  8. Place the thread slightly from the  
               front and to the back of threading 
               guide g. 
 
 
 
 
  9. Place the thread through h, i and j. 
  
 
 
 
 
 
 
      
 
                         
 
 
Three-Thread Overlock (narrow) page 10  
						

							 
   
 
Three-Thread Overlock (narrow) page 11  
 10. Thread the looper eye (A) from front to back.  Pull about 4 inches of thread. 
                 Position thread into V cutout (B) on threader.  Firmly hold thread tail with left   
                 hand and pull Threader Lever (C) up into place (D).  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
 
     
 
 
 
 
 
 
NOTE: Make sure the Upper Looper thread is 
behind the Lower Looper thread. 
Threader Lever 
“V” cutout   
						

							 
  
  5. Continue to thread points 4-8.  Slip the thread into the rear slot of the  
      thread guide g.  Go over the take up lever h.  Continue by slipping the  
               thread into the right slot of the thread guides i and j.  
 
  8. Before threading the eye of the needle, make sure the thread is   
               behind
 the thread guide located on the bottom of the needle clamp. 
 
 
 
 
 
 
 
 
 
 
 
  
 
  
 
  
  9. Draw about 4 inches of the thread through the needle eye towards the back 
      of the machine.  
  
      10. Place the thread to the back, under the Presser Foot.   
 
 
 
 
 
 
 
 
 
Three-Thread Overlock (narrow) page 13