Smeg Lsa13x Instruction Manual
Have a look at the manual Smeg Lsa13x Instruction Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 81 Smeg manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
User instructions 9 3. Description of the controls 3.1 Upper panel All the dishwasher controls are grouped on the upper panel. Switch-on, programming, switch-off etc. procedures are only possible when the door is open. 1 ON/OFF BUTTON Pressing this button energises the appliance. 2 SELECTED PROGRAM INDICATOR LIGHTS Illumination of this light denotes the program selected and the occurrence of a fault (troubleshooting). 3 PROGRAM SELECTION BUTTON By pressing this button in sequence it is possible to select the desired program. 4 WATER HARDNESS ADJUSTMENT ON INDICATOR LIGHT The light flashes to indicate that the appliance is in “water hardness adjustment” mode. SALT WARNIN LIGHT (on some models only) If the symbol is present, illumination of this light denotes a regenerating salt warning level. 5 RINSE AID WARNING LIGHT (on some models only) Illumination of this light signals that rinse aid dispenser is empty. 6 QUICK TIME + EXTRA OPTION BUTTON (see “EXTRA OPTIONS” section) The button controls selection of the quick time programs. (see table). 7 QUICK TIME PROGRAM LIGHT Illuminates to indicate that one of the extra programs (see table) is going to be executed.
User instructions 10 8 ENERSAVE OPTION + EXTRA OPTION BUTTON (see “EXTRA OPTIONS” section) Press the button to enable/disable the option. 9 ENERSAVE OPTION LIGHT Illuminates to indicate that the function is activated. 10 HALF LOAD BUTTON Press this button to activate the half load wash option. 11 HALF LOAD LIGHT Illuminates to indicate that the function is activated. 12 3/1 OPTION (EXTRA OPTION) LIGHT Illuminates to indicate that the function is activated. 13 PROGRAM DELAY BUTTON Press this button to delay the start of the program. 14 INFORMATION DISPLAY (1 or 3 digits depending on model) N.B.: symbols and styling are guideline and may vary depending on the model or version of the dishwasher purchased. Information displayed no Scheduled program duration yes no Remaining program time yes 1 - 9 hours Delayed start 1 - 24 hours E Error message Err
User instructions 11 PROGRAMS TABLE The manual contains the programs table for several models. To find the table for your dishwasher, compare the program symbols at the top of the table with those on your control panel. SETTING THE WASHING PROGRAM AND SWITCHING ON After identifying the most suitable program with the aid of the programs table: • Press the ON/OFF button (1) and wait for the PROGRAM INDICATOR LIGHT (2) to illuminate; • Keep pressing the PROGRAM SELECTION button (3) until the indicator light corresponding to the desired program illuminates; • select the option required (if any and if the model provides options); • close the door; after about 2 the program will start LIGHT will flashing (indicating that the program is being executed). Some components are live even with the ON/OFF button in the OFF position. Before maintenance work on the appliance, remove the plug or turn off the power supply at the wall switch.
User instructions
12
PROGRAMS TABLE
PROGRAMME, NUMBER & SYMBOL
LOAD CROCKERY AND CUTLERY
PROGRAM PROGRESS
DURATION CONSUMPTION
MINUTES (1)
WATER LITRES
POWER KWh (1)
1 SOAK
Pans and dishes awaiting completion of the load. Cold prewash
15’ ***
3,5 0,02
2 LIGHT
Delicate dishes with normal dirt.
Wash at 45°C Cold rinse Rinse at 70°C Dry
65 ***
9,5 1,10
3 ECO (*)
EN 50242
Dishes with normal dirt, even with dried-on residues.
Cold prewash Wash at 50°C Cold rinse Rinse at 55°C Dry
**
** **
4 AUTO 60-70
IEC/DIN****
Pans and dishes with normal dirt, even with dried-on residues.
When the AUTO program is selected, the dishwasher recognises the type of dirt and automatically adjusts the washing parameters as appropriate.
5 SUPER
*****
Very dirty pans and dishes, even with dried-on residues.
Hot prewash Wash at 70°C Cold rinse (3) Rinse at 70°C Dry
155 ***
15,5 1,60
IMPORTANT: see “NOTES AND REFERENCES” table on the following pages.
The washing cycle will not take place if the dishwasher door is left open
or not properly closed.
User instructions 13 QUICK TIME PROGRAMS (see relevant section for explanation of functioning modes) PROGRAMME NUMBER E SYMBOL LOAD CROCKERY AND CUTLERY PROGRAM PROGRESS DURATION CONSUMPTION MINUTI (1) WATER LITRES POWER KWh (1) 6 RAPID 27’ + Dishes with light dirt, washed immediately after use Wash at 38°C Rinse at 50°C 27*** 6,5 0,70 7 ECO QUICK + Dishes with normal dirt, washed immediately after use. Cold prewash Wash at 55°C Cold rinse Rinse at 70°C 80’*** 12,5 1,25 8 DAILY + Dishes with normal dirt, washed immediately after use. Wash at 65°C Cold rinse Rinse at 70°C Dry 95’*** 11 1,25 9 STRONG and FAST + Mixed dishes with normal dirt without dried-on residues. Wash at 65°C Cold rinse Rinse at 70°C 55’*** 9,5 1,35 IMPORTANT: see “NOTES AND REFERENCES” table on the following pages. The washing cycle will not take place if the dishwasher door is left open or not properly closed.
User instructions 14 PROGRAMS TABLE PROGRAMME NUMBER & SYMBOL LOAD CROCKERY AND CUTLERY PROGRAM PROGRESS DURATION CONSUMPTION MINUTES (1) WATER LITRESPOWER KWh (1) 1 SOAK Pans and dishes awaiting completion of the load Cold prewash 15*** 3,5 0,02 2 GLASS Glass, china and mixed dishes with light dirt. Wash at 45°C Cold rinse Rinse at 70°C Dry 65*** 9,5 1,10 3 ECO (*) EN 50242 Dishes with normal dirt, even with dried-on residues Cold prewash Wash at 50°C Cold rinse Rinse at 55°C Dry ** ** ** 4 NORMAL IEC/DIN**** Dishes with normal dirt, even with dried-on residues Cold prewash Wash at 65°C Cold rinse Rinse at 70°C Dry 105’*** 13,5 1,35 5 ULTRA CLEAN ***** Very dirty pans and dishes, even with dried-on residues. Hot prewash Wash at 70°C Cold rinse (3) Rinse at 70°C Dry 160*** 15,5 1,70 IMPORTANT: see “NOTES AND REFERENCES” table on the following pages. The ULTRA CLEAN program terminate with an extra anti-bacteria rinse that ensures a further reduction in the bacteria level. If the temperature falls during this stage of the program (e.g. because the door is opened or due to a power blackout), the program lights flash to warn that the anti-bacteria effect is not guaranteed. If the dishwasher door is open or not properly closed, the washing cycle will not start.
User instructions 15 QUICK TIME PROGRAMS (see relevant section for explanation of functioning modes) PROGRAMME NUMBER E SYMBOL LOAD CROCKERY AND CUTLERY PROGRAM PROGRESS DURATION CONSUMPTION MINUTI (1) WATER LITRES POWER KWh (1) 6 RAPID 27’ + Dishes with light dirt, washed immediately after use Wash at 38°C Rinse at 50°C 27*** 6,5 0,70 7 ECO QUICK + Dishes with normal dirt, washed immediately after use. Cold prewash Wash at 55°C Cold rinse Rinse at 70°C 80’*** 12,5 1,25 8 DAILY + Dishes with normal dirt, washed immediately after use. Wash at 65°C Cold rinse Rinse at 70°C Dry 95’*** 11 1,25 9 STRONG and FAST + Mixed dishes with normal dirt without dried-on residues. Wash at 65°C Cold rinse Rinse at 70°C 55*** 9,5 1,35 If the dishwasher door is open or not properly closed, the washing cycle will not start.
User instructions
16
NOTES AND REFERENCES Only run the soak program with half loads. Options cannot be used with the soak program.
* Standard programme under EN 50242. If present, the ENERSAVE option must
be enabled.
** See information sheet provided
*** IEC/DIN reference programme. If present, the ENERSAVE option must be
enabled.
**** Reference program for laboratories: Detergent: 20g in the dispenser + 10g in the
door or tablet. Configuration: see photo in “Using the baskets”.
(1) The cycle duration and power consumption may vary according to the water and
room temperatures, and the type and amount of dishes.
(2) 1 or 2 cold rinses depending on the model.
REFERENCES for the ENERGY LABEL supplied with the dishwasher:
- Annual energy consumption is based on 280 standard wash cycles with cold
water and consumption of low-energy operating modes. Actual consumption
depends on the way in which the appliance is used.
- Water consumption is based on 280 standard wash cycles. Actual
consumption depends on the way in which the appliance is used.
- Information refers to the EN 50242 STANDARD programme (identified in the
programmes table), which is the most effective in terms of combined energy
and water consumption. The programme is recommended for dishes with a
normal level of dirt.
- Energy consumption in “sleep” mode = 0.02 W.
- Energy consumption in “on” mode = 1.5 W.
- Drying efficiency class on a scale from “G” (minimum efficiency) to “A”
(maximum efficiency).
User instructions 17 3.2 Washing programs Before starting a washing program make sure that: • The water supply tap is open. • The correct amount of detergent has been added to the dispenser. • The baskets have been correctly loaded. • The spray arms are able to rotate freely and without obstruction. • The dishwasher door is securely closed. QUICK TIME PROGRAMS Select this option together with any washing program (except the soak program) to SHORTEN the cycle by from a minimum of 10% to a maximum of 55%, depending on the cycle selected. To activate this option, press the QUICK TIME button (light comes on) after selecting the program required. The option is automatically deactivated at the end of the program. ENERSAVE This option can be selected with the wash programme of choice to further reduce energy consumption. Drying is aided by a special device that automatically releases the door, which opens slowly and smoothly by a few centimetres. This ensures perfect drying and greater control of rinsing temperatures, which can be kept at lower levels for significant energy saving. Once the door has opened, the dishwasher emits a short beep and programme lights nos. 4 and 5 (marked “end”) flash to indicate the end of the washing cycle. Enersav e is activated automatically every time a wash cycle is selected (except for programs that do not include the final drying phase; see programs table) and can be disabled before the program is started. When the function is activated, opening of the door must not be impeded in any way; do not leave anything in the space in front of the door necessary to allow it to open. Do not re-close the door during automatic opening as this would damage the mechanism. Wait for the pushers to retract before re-closing the door.
User instructions 18 SPREAD HALF LOAD Suitable when there are not many dishes to be washed, it saves energy and reduces the program duration. Place dishes in both baskets then load the detergent dispenser than less than the normal amount for a full load. EXTRA OPTIONS - “Flexi Tabs” BUTTON Press buttons 6 + 8 (QUICK TIME PROGRAMS button + ENERSAVE option button) simultaneously to activate the Flexi Tabs option; the respective light comes on to confirm the selection. The option is optimised for use of detergents which are complete with salt and rinse aid, known on the market as, triple action, etc. With this option activated, any salt and rinse aid If you wish to use detergents which already contain salt and rinse aid already in the dishwasher will not be used. N.B.: even with the Flexi Tabs option selected, the regenerating salt/rinse aid lights will still stay on if their containers are empty. IMPORTANT: the option continues to be active until it is deactivated by pressing buttons 6 + 8 simultaneously; the light will then go out. This products are not suitable for use with excessively hard water. Therefore, if the water hardness is set higher than H3, the Flexi Tabs OPTION light flashes to indicate a setting error. This does not prevent the use of the option, but the washing results might not be of the best. DELAYED START The start of the washing program can be delayed to program the dishwasher to operate at the preferred time of day (e.g. overnight). Press the PROGRAM DELAY button to activate the option and display a 1 hour delay. Keep pressing to select the delay required, which may be up to 9, 12 or 24 hours depending on the model. When the door is closed, the appliance will prewash the dishes, after which the program delay set will come into effect.