Smeg Pgf64-4 Manual

							21
Contents
THESE INSTRUCTIONS ARE VALID ONLY FOR THE DESTINATION COUNTRIES
WHOSE IDENTIFYING SYMBOLS ARE INCLUDED ON THE COVER OF THIS
MANUAL.
INSTRUCTIONS FOR THE USER: these instructions contain user
recommendations, a description of the controls and the correct
procedures for cleaning and maintenance of the appliance.
INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified
technician who must install the appliance, set it functioning and carry out
an inspection test.
1. INSTRUCTIONS FOR USE .............................................................. 22
2. SAFETY PRECAUTIONS ................................................................. 24
3. ENVIRONMENTAL RESPONSIBILITY ............................................. 26
4. USING THE HOB.............................................................................. 27
5. CLEANING AND MAINTENANCE .................................................... 29
6. POSITION NEAR THE COUNTER TOP  ......................................... 30
7. ADAPTATION TO DIFFERENT TYPES OF GAS ............................ 36
8. FINAL OPERATIONS ....................................................................... 38 
						

							General instructions
22
1. INSTRUCTIONS FOR USE
THIS MANUAL CONSTITUTES AN INTEGRAL PART OF THE APPLIANCE. THIS
MANUAL CONSTITUTES AN INTEGRAL PART OF THE APPLIANCE. IT SHOULD BE
KEPT INTACT AND AT HAND FOR THE APPLIANCE’S ENTIRE LIFE CYCLE.
IT IS IMPORTANT TO CAREFULLY READ THIS MANUAL AND ALL THE
INSTRUCTIONS CONTAINED HEREIN BEFORE USING THE APPLIANCE.
INSTALLATION MUST BE CARRIED OUT BY QUALIFIED PERSONNEL AND COMPLY
WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS SPECIFIED FOR
DOMESTIC USE, AND COMPLIES WITH THE EEC DIRECTIVES CURRENTLY IN
FORCE. THE APPLIANCE IS MANUFACTURED IN ORDER TO PERFORM THE
FOLLOWING FUNCTIONS: COOKING FOOD; IT IS CONSIDERED UNSUITABLE FOR
ANY OTHER USE.
THE MANUFACTURER CANNOT BE HELD RESPONSIBLE FOR USES OTHER THAN
THOSE INDICATED. 
IF THE APPLIANCE IS INSTALLED ON BOATS OR IN CARAVANS, DO NOT USE IT AS
A ROOM HEATER.
NEVER USE THIS APPLIANCE TO HEAT YOUR ENVIRONMENT.
THIS APPLIANCE IS MARKED FOR IDENTIFICATION PURPOSES IN ACCORDANCE
WITH THE EUROPEAN DIRECTIVE 2002/96/EC ON WASTE ELECTRICAL AND
ELECTRONIC EQUIPMENT - WEEE).
THIS DIRECTIVE STATES THAT THE REGULATIONS FOR THE COLLECTION AND
RECYLING OF DISCARDED APPLIANCES ARE VALID WITHIN THE EUROPEAN
UNION.
BEFORE OPERATING THE APPLIANCE, IT IS MANDATORY TO REMOVE ALL
PROTECTIVE FILM.
SUITABLE HEAT-PROOF GLOVES SHOULD BE WORN FOR ALL OPERATIONS.
DO NOT USE STEEL SPONGES AND SHARP SCRAPERS AS THEY WILL
DAMAGE THE SURFACE.
USE NORMAL NON-ABRASIVE PRODUCTS, INCLUDING WOODEN OR
PLASTIC UTENSILS IF NECESSARY. RINSE THOROUGHLY AND DRY
USING A SOFT CLOTH OR A MICROFIBRE CLOTH.
DO NOT LEAVE THE APPLIANCE UNATTENDED DURING COOKING PROCESSES
WHERE FATS OR OILS COULD BE RELEASED.
FATS AND OILS MAY CATCH FIRE. 
						

							General instructions
23
ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE  O (OFF) POSITION
WHEN YOU FINISH USING THE APPLIANCE 
NEVER PLACE PANS WITH BOTTOMS WHICH ARE NOT PERFECTLY FLAT AND
SMOOTH ON THE COOKING HOB PAN STANDS.
NEVER USE PANS OR GRIDDLE PLATES WHICH PROJECT BEYOND THE OUTSIDE
EDGE OF THE HOB. 
						

							General instructions
24
2. SAFETY PRECAUTIONS
REFER TO THE INSTALLATION INSTRUCTIONS FOR THE SAFETY REGULATIONS
FOR ELECTRIC OR GAS APPLIANCES AND VENTILATION FUNCTIONS.
IN YOUR INTERESTS AND FOR YOUR SAFETY THE LAW REQUIRES THAT THE
INSTALLATION AND SERVICING OF ALL ELECTRICAL APPLIANCES IS CARRIED
OUT BY QUALIFIED PERSONNEL IN ACCORDANCE WITH THE REGULATIONS IN
FORCE.
OUR APPROVED INSTALLERS GUARANTEE A SATISFACTORY JOB.
GAS OR ELECTRICAL APPLIANCES MUST ALWAYS BE DISCONNECTED BY
SUITABLY SKILLED PEOPLE.
BEFORE CONNECTING THE APPLIANCE TO THE POWER GRID, CHECK THE DATA
ON THE PLATE AGAINST THE DATA FOR THE GRID ITSELF.
THE IDENTIFICATION PLATE CONTAINING THE TECHNICAL DATA, SERIAL NUMBER
AND BRAND NAME IS IN A VISIBLE POSITION UNDER THE CASING. 
DO NOT REMOVE THIS PLATE ON THE CASING FOR ANY REASON.
BEFORE CONNECTING THE DEVICE, MAKE SURE THAT IT HAS BEEN REGULATED
FOR THE TYPE OF GAS THAT WILL FEED IT, CHECKING THE LABEL UNDER THE
CASING.
BEFORE CARRYING OUT INSTALLATION/MAINTENANCE WORK, MAKE SURE THAT
THE APPLIANCE IS NOT CONNECTED TO THE POWER GRID.
THE PLUG TO BE CONNECTED TO THE POWER SUPPLY CABLE AND ITS SOCKET
MUST BE OF THE SAME TYPE AND CONFORM TO THE REGULATIONS IN FORCE.
THE SOCKET MUST BE ACCESSIBLE AFTER THE APPLIANCE HAS BEEN BUILT IN.
NEVER DISCONNECT THE PLUG BY PULLING ON THE CABLE.
IF THE POWER SUPPLY CABLE IS DAMAGED, CONTACT THE TECHNICAL SUPPORT
SERVICE IMMEDIATELY AND THEY WILL REPLACE IT.
IT IS OBLIGATORY FOR ALL ELECTRICAL EQUIPMENT TO BE EARTHED
ACCORDING TO THE METHODS LAID DOWN BY SAFETY REGULATIONS.
IMMEDIATELY AFTER INSTALLATION, CARRY OUT A BRIEF INSPECTION TEST,
FOLLOWING THE INSTRUCTIONS BELOW. SHOULD THE APPLIANCE NOT
FUNCTION, DISCONNECT IT FROM THE ELECTRICITY SUPPLY AND CALL THE
NEAREST TECHNICAL SUPPORT CENTRE.
NEVER ATTEMPT TO REPAIR THE APPLIANCE.
DURING USE THE APPLIANCE BECOMES VERY HOT. MAKE SURE YOU DO NOT
TOUCH THE HEATING ELEMENTS. 
						

							General instructions
25
THIS APPLIANCE MAY NOT BE USED BY PEOPLE (INCLUDING CHILDREN) OF
REDUCED PHYSICAL AND MENTAL CAPACITY, OR LACKING IN EXPERIENCE IN
THE USE OF ELECTRICAL APPLIANCES, UNLESS THEY ARE SUPERVISED OR
INSTRUCTED BY ADULTS RESPONSIBLE FOR THEIR SAFETY.
DO NOT LET CHILDREN GO NEAR THE APPLIANCE WHEN IT IS IN OPERATION OR
PLAY WITH IT AT ANY TIME.
DO NOT INSERT POINTED METAL OBJECTS (CUTLERY OR UTENSILS) INTO THE
SLITS IN THE APPLIANCE.
DO NOT USE STEAM JETS FOR CLEANING THE APPLIANCE. 
THE STEAM COULD REACH THE ELECTRONICS, DAMAGING THEM AND CAUSING
SHORT-CIRCUITS.
DO NOT MODIFY THIS APPLIANCE.
DO NOT SPRAY ANY SPRAY PRODUCTS NEAR THE ELECTRICAL APPLIANCE
WHILE IT IS IN OPERATION.
DO NOT USE SPRAY PRODUCTS WHILE THE PRODUCT IS STILL HOT.
The manufacturer cannot be held liable for damage to persons or things caused by
failure to observe the above instructions, by interference with any part of the
appliance or by the use of non-original spare parts. 
						

							Instructions for disposal
26
3. ENVIRONMENTAL RESPONSIBILITY
3.1 Our environmental responsibility
Pursuant to Directives 2002/95/EC, 2002/96/EC and 2003/108/EC relating to
the reduction of the use of hazardous substances in electrical and electronic
appliances, as well as to the disposal of refuse, the crossed out bin symbol on
the appliance indicates that at the end of the useful life of the product, it must be
collected separately from other refuse. Therefore, at the end of the products
working life, the user must deliver it to the appropriate differentiated collection
centres for electrical and electronic waste, or deliver it back to the retailer when
purchasing an equivalent product, on a one-for-one basis. Adequate
differentiated collection for the subsequent forwarding of the decommissioned
product to recycling, processing and ecologically compatible disposal
contributes to avoiding possible negative effects on the environment and on
health, and promotes recycling of the appliances constituent materials. Illicit
disposal of the product by the user will lead to the application of administrative
sanctions.
The product does not contain substances in quantities sufficient to be
considered hazardous to health and the environment, in accordance with
current European directives.
3.2 Your environmental responsibility
Our products packing is made of non-polluting materials, which are therefore
compatible with the environment and recyclable. Please help by disposing of the
packaging correctly. You can obtain the addresses of collection, recycling and
disposal centres from your retailer or from the competent local organisations.
Do not discard the packaging or any part of it, or leave it unattended. It can
constitute a suffocation hazard for children, especially the plastic bags.
Your old appliance also needs to be disposed of correctly.
Important: hand over your appliance to the local agency authorised for the
collection of electrical appliances no longer in use. Correct disposal enables
intelligent recovery of valuable materials.
Before disposing of your appliance it is important to remove doors and leave
shelves in the same position as for use, to ensure that children cannot
accidentally become trapped inside during play. It is also necessary to cut the
connecting cable to the power grid, removing it along with the plug. 
						

							Instructions for the user
27
4. USING THE HOB
4.1 Lighting the hob burners
Before lighting the hob burners, check that the flame-spreader crowns are
correctly in place with their respective burner caps, making sure that the holes A
in the flame-spreaders are aligned with the igniters and thermocouples.
To prevent damage to the work top, the hob comes complete with a raised pan
stand H. This must be placed under pans with a diameter bigger than those
indicated in the table in paragraph 4.3 Pan diameters. In any case, pans with a
diameter greater than 28 cm must be used solely on the central burner.
The pan stand H can also be used with woks.
The burner controlled by each knob is shown next to the knob.
The appliance is equipped with an electrical ignition device.
Simply press the knob and turn it anti-clockwise to the
maximum flame symbol  , until the burner lights.
On valved models, once the burner is lit, keep the knob pressed for a few
seconds to give the thermocouple time to heat up. The burner may go out when
the knob is released: in this case, the thermocouple has not heated up
sufficiently.
Wait a few moments and repeat the operation keeping the knob pressed for
longer. This is not necessary on burners that are not equipped with a
thermocouple.
Once the burner is lit, the flame can be adjusted as required.
Always check that the control knobs are in the O (off) position when you finish
using the hob.
If the burners should go out accidentally, after about 20 seconds a safety device
will be tripped, cutting off the gas supply, even if the gas tap is open. Turn off the
control knob and wait at least 1 minute before trying to re-light the burner.
A
H
A 
						

							Instructions for the user
28
4.2 Practical tips for using the burners
For better burner efficiency and to minimise gas consumption, use pans with a
flat, smooth base and a lid that have a suitable size for the burner, thus
preventing the flames reaching the sides of the pan (see paragraph “4.3 Pan
Diameter”). Once the contents come to the boil, turn down the flame far enough
to prevent the liquid from boiling over.  
To prevent burns or damage to the hob during cooking, all pans or griddles must
be placed inside the perimeter of the hob. 
Take the greatest care when using fats or oils since they may catch fire if
overheated.
4.3 Pan diameters
HOB BURNER
1  Auxiliary
2  Rapid
3  Ultra-rapidØ min. and max. 
(in cm)
12-16
18-24
22-26
4.3.1 Pan diameters with raised pan stand
HOB BURNER
1  Auxiliary
2  Rapid
3  Ultra-rapidØ min. and max. 
(in cm)
16-26
24-28
26-34 
						

							Instructions for the user
29
5. CLEANING AND MAINTENANCE
Before performing any operations requiring access to powered parts,
switch off the power supply to the appliance.
NEVER USE A STEAM JET FOR CLEANING THE APPLIANCE.
5.1 Cleaning stainless steel
To keep stainless steel in good condition it should be cleaned regularly
after use. Let it cool first.
5.1.1 Ordinary daily cleaning
To clean and preserve the stainless steel surfaces, use only specific products
that do not contain abrasives or chlorine-based acids.
How to use: pour the product onto a damp cloth and wipe the surface, rinse
thoroughly and dry with a soft cloth or chamois leather.
5.1.2 Food stains or residues
Never use metallic sponges or sharp scrapers as they will damage the
surface.
Use ordinary non-abrasive products for steel, with the aid of wooden
or plastic utensils if necessary.
Rinse thoroughly and dry with a soft cloth or chamois leather.
5.2 Cleaning the cooking hob parts
For easier cleaning the pan stands, burner caps, flame
spreader crowns and burners can all be removed; wash them
with warm water and a non-abrasive detergent making sure to
remove any encrustation, then wait until they are completely
dry. Replace the burner caps on their corresponding crowns,
making sure that the slots A are centred with the pins B on the
burners.
For correct operation, the igniters and thermocouples must
always be perfectly clean. Check them frequently and clean
them with a damp cloth if necessary. Remove any dry residues
with a wooden toothpick or a needle. 
						

							Instructions for the installer
30
6. POSITION NEAR THE COUNTER TOP
The following operation requires building and/or carpentry work so must be carried out by
a competent tradesman.
Installation can be carried out on various materials such as masonry, metal, solid wood or
plastic laminated wood as long as they are heat resistant (T 90°C).
6.1 Fixing to a support structure model with traditional casing
(fig. 1)
Create an opening with the
dimensions shown in the figure in the
work surface of the piece of furniture.
1)
A (mm)B (mm)C (mm)D (mm)E (mm)L (mm)X (mm)Y (mm)
min 150min 460min 75020÷50min 50620592488
Carefully position the supplied insulating
seal on the outer edge of the hole on the
top hob, as indicated in figure 2. Try and
make it stick to the whole surface by
applying light hand pressure. The front and
back sides of the seal must be touching the
hole. 
2)
Carry out this operation by supporting the
hob on the isolating seal and using screws
and clamping brackets (Fig. 3) to fix the
hob to the support structure, in order to
obtain the complete flatness. 
Trim any excess trimming from border A
with care (Fig.4). The quotes in figure 2 are
references for the hole on the inside of the
trimming. The small brackets in figure 3 are
only positioned after having mounted the
hob.  3)
 4)