Smeg Se336ss5 User Manual

							
Contents  
 
1. INSTRUCTIONS FOR SAFE AND PROPER USE _______________ 28 
2. INSTALLATION _________________________________________ 30 
3. DESCRIPTION OF CONTROLS ____________________________ 34 
4. USE OF THE OVEN ______________________________________ 40 
5. AVAILABLE ACC ESSORIES _______________________________ 41 
6. COOKING HINTS ________________________________________ 42 
7. CLEANING AND MAINTENANCE ___________________________ 47 
8. ADDITIONAL MAINTENANCE ______________________________ 49 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
INSTRUCTIONS FOR THE INSTALLER:  these are intended for the 
qualified technician who must install the appl iance, set it functioning 
and carry out an inspection test. 
 
 
INSTRUCTIONS FOR THE USER: these contain user advice, 
description of the controls and the correct procedures for cleaning and 
maintenance of the appliance. 
27  
						

							
 Introduction 
 
1. INSTRUCTIONS FOR SAFE AND PROPER USE 
 
 
THIS MANUAL IS  AN INTEGRAL PART OF THE APPLIANCE AND 
THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE 
PLACE FOR THE WHOLE WORKING LIFE OF THE OVEN. WE ADVISE 
CAREFUL READING OF THIS MANUAL AND ALL THE INSTRUCTIONS 
THEREIN BEFORE USING THE OVEN. INSTALLATION MUST BE CARRIED 
OUT BY QUALIFIED PERSONNEL IN ACCORDANCE WITH THE 
REGULATIONS IN FORCE. THIS APPLIANCE IS INTENDED FOR DOMESTIC 
USES AND CONFORMS TO CURRENT  REGULATIONS IN FORCE. THE 
APPLIANCE HAS BEEN BUILT TO CARRY OUT THE FOLLOWING 
FUNCTIONS:  COOKING AND HEATING-UP OF FOOD . ALL OTHER USES 
ARE CONSIDERED IMPROPER. 
THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR IMPROPER 
USE.  
  
  
 
DO NOT LEAVE THE PACKING IN THE HOME ENVIRONMENT.  SEPARATE 
THE VARIOUS WASTE MATERIALS  AND TAKE THEM TO THE NEAREST 
SPECIAL GARBAGE COLLECTION CENTRE. 
  
  
 
IT IS OBLIGATORY FOR THE ELECTRICAL SYSTEM TO BE EARTHED  
ACCORDING TO THE METHODS REQUIRED BY SAFETY RULES. 
   
 
WHEN LINKING UP TO MAINS BY PLUG AND SOCKET, MAKE SURE THAT 
BOTH ARE COMPATIBLE AND CONNECT BY MEANS OF A POWER CABLE 
COMPLYING WITH APPLICABLE REGULATIONS. 
THE SOCKET MUST BE ACCESSIBLE AFTER THE APPLIANCE HAS BEEN 
BUILT IN. 
NEVER UNPLUG BY PULLING ON THE CABLE.   
   
DO NOT OBSTRUCT VENTILATION OUTLETS AND HEAT DISPERSAL SLITS. 
  
IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF INSPECTION 
TEST OF THE OVEN, FOLLOWING TH E INSTRUCTIONS BELOW. SHOULD 
THE APPLIANCE NOT FUNCTION, DISCONNECT IT FROM THE SUPPLY AND 
CALL THE NEAREST TECHNICAL ASSISTANCE CENTRE. 
NEVER ATTEMPT TO REPAIR THE APPLIANCE.  
28   
						

							
Introduction   
   
ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE “ZERO” (OFF) 
POSITION WHEN YOU FINISH USING THE OVEN. 
 
  
NEVER PUT INFLAMMABLE OBJECTS IN THE OVEN: THEY COULD BE 
ACCIDENTALLY CATCH LIGHT AND CAUSE FIRES. 
  
DURING USE THE APPLIANCE BECOMES VERY HOT. TAKE CARE NOT TO 
TOUCH THE HEATING ELEMENTS INSIDE THE OVEN. 
  
THE I.D. PLATE WITH TECHNICAL DATA, REGISTRATION NUMBER AND 
BRAND NAME IS POSITIONED VISIBLY ON THE OVEN DOOR FRAME. 
THE PLATE MUST NOT BE REMOVED.  
  
 
THE USE OF THIS APPLIANCE IS NOT PERMITTED TO PEOPLE (INCLUDING 
CHILDREN) OF REDUCED PHYSICAL AND MENTAL ABILITY, OR LACKING IN 
EXPERIENCE IN THE USE OF ELECTRICAL APPLIANCES, UNLESS THEY 
ARE SUPERVISED OR INSTRUCTED BY ADULTS OR PEOPLE 
RESPONSIBLE FOR THEIR SAFETY. 
 
 
THIS APPLIANCE IS MARKED ACCORDING TO THE EUROPEAN DIRECTIVE 
2002/96/EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT 
(WEEE). 
THIS GUIDELINE IS THE FRAME OF A EUROPEAN-WIDE VALIDITY OF 
RETURN AND RECYCLING ON WASTE ELECTRICAL AND ELECTRONIC 
EQUIPMENT. 
 
  
BEFORE THE APPLIANCE IS PUT INTO OPERATION, ALL THE LABELS AND 
PROTECTIVE FILMS APPLIED INSIDE OR OUTSIDE MUST BE REMOVED. 
 
 
 The manufacturer declin es all responsibility for damage to persons 
or things caused by non-observan ce of the above guidlines or by 
interference with any part of the appl iance or by the use of non-original 
spares.  
29  
						

							
 
 
Instructions for the installer 
 
30 
2. INSTALLATION 
 
2.1  Electrical connection 
 
Check that the mains voltage and power cable ratings are as per the 
information provided on the label attached to the oven door frame.   
This label must never be removed. 
 
 
It is obligatory for the electrical system to be earthed according to the 
methods required by safety rules. 
 
 
If a plug and socket connection is being used make sure that the plug 
and socket are compatible. Avoid use of adapters and shunts as these 
could cause overheating and risk of burns. 
 
 
If a fixed connection is being used fit cable line with an omnipolar circuit 
breaker with a contact opening gap equal to or greater than  3 mm in an 
easily accessible position in proximity to the oven. 
  
  
 
For operation on 220-240V ∼: use an 
H05RR-F / H05RN-F type three-core cable 
(3 x 1.5 mm2).  
 
The cable end to be connected to the 
appliance must be provided with an ground 
wire (yellow-green) at least 20 mm longer.  
 
 
2.1.1  Ovens with hob controls 
In the ovens with hob controls the  power cable is not supplied. Use a 
H05RR-F or H05RN-F rubber-sheathed cable making sure that it does 
not come into contact with any external metal parts of the oven when 
routing. 
 
Remove rear cover by loosening relevant screws to gain access to the 
terminal strip. If necessary change jumper configuration as shown in the 
diagram and then connect wires making  sure that the earth wire is at 
least 20 mm longer than the others. Secure power cable to oven by 
means of  an appropriate fitting. 
  
						

							
 
Instructions for the installer 
 
 
 31 
       
  
 For operation on 220-240V ∼: use an 
H05RR-F / H05RN-F type three-core cable 
(3 x 4 mm2). 
 
 
 
For operation on 380-415V2N∼: use an 
H05RR-F / H05RN-F type four-core cable 
(4 x 2.5 mm2). 
 
 
 
 
For operation on 380-415V3N∼: use an 
H05RRF / H05RN-F type five-core cable
(5 x 1.5 mm2). 
 
 
The cable end to be connected to the 
appliance must be provided with an earth 
wire (yellow-green) at least 20 mm longer.  
 
  
 
 The manufacturer declin es all responsibility for damage to persons 
or things caused by non-observance of the above guidelines or by 
interference with any part of the appliance.    
						

							
 
 
Instructions for the installer 
 
32 
2.2  Installing the oven 
The oven is designed for installation into any piece of furniture as long as 
it is heat-resistant. Proceed according to the dimensions shown in Figures 
1,  2 and 3 . For installing under a work top, follow the dimensions given in 
Figure  3. For installing under a work top beneath a hob with controls 
connected to the oven, ensure a minimum clearance from any side walls 
of at least 110 mm as shown in Figure  1.  
For installing in a column, follow the dimensions given in Figure  2 allowing for a 
clearance of 80 to 90 mm at the top and sides of the column. Tighten the four 
screws (ref. A) inside the frame  to secure (Fig. 1). 
For installing beneath a separate hob, allow for a rear and bottom 
clearance as shown in Figure  1 (ref. B ). See relevant inst ructions for fitting 
and securing the hob.
  
   
						

							
 
Instructions for the installer 
 
 
 33  
  
 Never use the oven door to lever the oven into 
place when fitting. 
Avoid exerting too much pressure on the oven door 
when open. 
  
2.3 Connecting the hob to the oven 
Once installed, the hob must be connec ted to the oven. Install the oven 
allowing enough room for the following operations to take place.
 
•   Connect the earth wire (yellow-green)  of the hob to the earth terminal 
A  of the oven (see figure). 
•  Fit the hob connectors into the appropriate sockets in the top cover 
of the oven. Make sure that the colours and symbols of the 
connectors match those of the oven sockets. 
•  If the hob is equipped with a connector for the residual heat indicator, 
this must be fitted into the free socket on the right handside. 
The oven can now be fully mounted into the cabinet; make sure that the 
power cable is properly routed and does  not come into contact with parts 
which may become hot during operation. 
  
						

							
 
 
Instructions for the user 
 
34 
3. DESCRIPTION OF CONTROLS  
3.1  Front control panel 
All the oven controls are grou ped together on the front panel.  
  
 
 
The user has only to press the central key  for 1 - 2 seconds to enable 
use of the oven on first use or after a power blackout. 
 FUNCTION CONTROL KNOB  
Rotate the knob in either direction to select 
desired function from the following: 
 
  
NO FUNCTION SET   
  
UPPER AND LOWER  HEATING ELEMENT   
DEFROSTING 
  
GRILL ELEMENT 
  
UPPER AND LOWER 
HEATING ELEMENT + 
VENTILATION 
 
  
LOWER HEATING  ELEMENT   
FULL GRILL ELEMENT + 
VENTILATION 
 
UPPER AND LOWER 
HEATING ELEMENT + 
VENTILATED HEATING 
ELEMENT 
 
VENTILATED  HEATING ELEMENT 
 THERMOSTAT CONTROL KNOB  
Cooking temperature is selected by turning the 
knob clockwise to the desired setting, between 
50° and 250°C. 
 
  
						

							
 
Instructions for the user 
 
 
 35 
THERMOSTAT INDICATOR LIGHT (ORANGE) 
When this light comes on, the oven is heating up.  
When this light goes out, the preset heating 
temperature has been reached.  
When the light flashes, the temperature inside the 
oven is steady.  
 
PILOT LIGHT (GREEN) 
This light comes on when any of the oven elements 
is receiving power.  
  
HOB CONTROL KNOB 
Permits to adjust cook top heating. Rotate clockwise 
to set to desired value ( 2 to  12). 
  
HOB CONTROL KNOB  
WITH DUAL ZONES 
Used to select heating zone in plates 
with dual heating zones.  
   Rotating the knob clockwise from between  2 to 12 heats the inner zone 
within the small diameter. 
Setting knob to  or  and releasing it (knob returns to  12) causes both 
zones to be heated. To adjust heat in tensity, turn the knob anticlockwise 
to the desired value. 
To return to heating inside the inner zone only, set knob first to  0 and 
then to any value between  2 and  12 as desired.
 
  
						

							
 
 
Instructions for the user 
 
36 
3.2  Electronic Analogue Clock 
 
  
  LIST OF FUNCTIONS    
  
 MINUTE-MINDER BUTTON 
  
 AUTOMATIC SWITCH-OFF TIMING BUTTON 
  
 TIME SETTING AND RESET 
  
 VALUE DECREASE BUTTON 
 
 VALUE INCREASE BUTTON 
 
3.2.1  Setting the time 
When the oven is used for the first time, or after a power blackout, the 
display flashes on and off at regular intervals.  Press the 
 key for 1/2 
seconds to stop the display flashing a nd start setting of the current time. 
Press the value modification keys 
 or  to increase or decrease by 
one minute for each time a key is pressed. 
Press one of the two value modification keys until the current time 
appears. The clock will start from the time set 6/7 seconds after the last 
key is pressed. 
 
 
At the end of each programmed cook ing operation, the clock gives 8 
beeps, repeated 3/4 times at intervals of about 1 and a half minutes.  
The beeps can be stopped at any moment by pressing any key.